User's Manual
Table Of Contents
- HP 3PAR VMware ESX Implementation Guide
- Contents
- 1 Introduction
- 2 Configuring the HP 3PAR StoreServ Storage for Fibre Channel
- 3 Configuring the HP 3PAR StoreServ Storage for iSCSI
- 4 Configuring the HP 3PAR StoreServ Storage for FCoE
- 5 Configuring the Host for a Fibre Channel Connection
- Installing the HBA and Drivers
- Installing Virtual Machine Guest Operating System
- Multipath Failover Considerations and I/O Load Balancing
- Performance Considerations for Multiple Host Configurations
- ESX/ESXi 4.1, ESXi 5.x Additional Feature Considerations
- Storage I/O Control
- vStorage APIs for Array Integration (VAAI)
- HP 3PAR VAAI Plugin 1.1.1 for ESXi 4.1
- HP 3PAR VAAI Plugin 2.2.0 for ESXi 5.x
- UNMAP (Space Reclaim) Storage Hardware Support for ESXi 5.x
- Out-of-Space Condition for ESX 4.1 and ESXi 5.x
- Additional New Primitives Support on ESXi 5.x
- VAAI and New Feature Support Table
- VAAI Plugin Verification
- VMware All Paths Down
- 6 Configuring the Host as an FCoE Initiator Connecting to a FC target or an FCoE Target
- 7 Configuring the Host for an iSCSI Connection
- Setting Up the Switch, iSCSI Initiator, and iSCSI target ports
- Installing iSCSI on VMware ESX
- Installing Virtual Machine Guest Operating System
- Creating a VMkernel Port
- Configuring a Service Console Connection for the iSCSI Storage
- Configuring the VMware iSCSI Initiator
- iSCSI Failover Considerations and Multipath Load Balancing
- Performance Considerations for Multiple Host Configurations
- ESX/ESXi Additional Feature Considerations
- 8 Allocating Storage for Access by the ESX Host
- 9 Booting the VMware ESX Host from the HP 3PAR StoreServ Storage
- 10 Support and Other Resources
- 11 Documentation feedback
3. Issue the HP 3PAR OS CLI showport -iscsi command to check the current settings of the
iSCSI ports:
# showport -iscsi
N:S:P State IPAddr Netmask Gateway TPGT MTU Rate DHCP iSNS_Prim iSNS_Sec
iSNS_Port
0:1:1 offline 0.0.0.0 0.0.0.0 0.0.0.0 11 1500 n/a 0 0.0.0.0 0.0.0.0.0
3205
1:1:1 offline 0.0.0.0 0.0.0.0 0.0.0.0 12 1500 n/a 0 0.0.0.0 0.0.0.0.0
3205
0:1:1 offline 0.0.0.0 0.0.0.0 0.0.0.0 111 1500 n/a 0 0.0.0.0 0.0.0.0.0
3205
1:1:1 offline 0.0.0.0 0.0.0.0 0.0.0.0 112 1500 n/a 0 0.0.0.0 0.0.0.0.0
3205
4. Issue the HP 3PAR OS CLI controliscsiport command to set up the IP address and
netmask address of the iSCSI target ports.
# controliscsiport addr 10.1.1.100 255.255.255.0 -f 0:1:1
# controliscsiport addr 10.1.1.102 255.255.255.0 -f 0:1:1
# controliscsiport addr 10.1.1.101 255.255.255.0 -f 0:1:2
# controliscsiport addr 10.1.1.103 255.255.255.0 -f 0:1:2
NOTE: Make sure the IP switch ports where the HP 3PAR StoreServ Storage iSCSI target
port(s) and iSCSI initiator host are connected are able to communicate with each other by
using the vmkping command on the ESX host. (The VMware ESX host iSCSI initiator must be
configured to perform this operation in accordance with “Configuring the Host for an iSCSI
Connection” (page 65).)
To verify that the ESX host can see the HP 3PAR StoreServ Storage, use the vmkpingcommand:
# vmkping 10.1.1.100
To verify that the HP 3PAR StoreServ Storage can see the ESX host, issue the following
command:
# controliscsiport ping 10.1.1.10 0:1:1
NOTE: A maximum of 64 host iSCSI initiator ports can be connected to any one HP 3PAR
StoreServ Storage target port.
NOTE: When the host initiator port and the HP 3PAR OS target port are in different IP
subnets, the gateway address for the HP 3PAR OS port should be configured in order to avoid
unexpected behavior.
Creating the iSCSI Host Definition on an HP 3PAR StoreServ Storage Running HP 3PAR
OS 3.1.x and OS 2.3.x
Create a host definition that ties all of the connections from a single host to a host name. Prior to
creating a host definition using the following steps, the HP 3PAR StoreServ Storage iSCSI target
ports must have been set up and an iSCSI connection/session must be established. The iSCSI
connection/session is established by following the steps in “Setting Up the Ports for an iSCSI
Connection” (page 18) and the steps in “Configuring the Host for an iSCSI Connection” (page 65)
through “Configuring the VMware iSCSI Initiator” (page 72) (ESX host setup).
Software iSCSI Support 19