HP EliteDisplay E190i LED Backlit IPS Monitor User Guide
© 2013 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
About This Guide This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
iv About This Guide
Table of contents 1 Product Features ............................................................................................................................................ 1 HP LCD Monitors ................................................................................................................................. 1 2 Setting Up the Monitor ...................................................................................................................................
vi
1 Product Features HP LCD Monitors The LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) panel. The monitor's features include: ● EliteDisplay E190i model, 47.99 cm (18.
2 ● Intelligent Management AssetControl ● Compliant with the following regulated specifications (for additional certifications and agency notices, refer to the HP LCD Monitors Reference Guide on the disc included with this monitor): ◦ European Union CE Directives ◦ Swedish TCO Requirements Chapter 1 Product Features
2 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. Attaching the Stand to the Monitor 1. Lift the monitor from its box and place it face down on a flat surface. 2. Attach the base to the stand. 3. Tighten the screw on the bottom of the stand by hand.
Rear Components 4 Component Function 1 AC Power Connector Connects the AC power cord to the monitor 2 DisplayPort Connects the DisplayPort cable to the monitor (select regions only) 3 DVI-D Connects the DVI-D cable to the monitor 4 VGA Connects the VGA cable to the monitor 5 USB Upstream Connector Connects the USB hub cable to the monitor's USB hub connector and to a host USB port/hub 6 USB Downstream Connectors (2) Connects optional USB devices to the monitor Chapter 2 Setting Up the
Connecting the Cables 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Remove the cable management clip from the pedestal by pulling outward on the two sides of the clip (1) then lifting the clip off the pedestal (2). 3. Connect a VGA signal cable, DVI-D signal cable, or DisplayPort signal cable. NOTE: The monitor is capable of supporting either analog or digital input. The video mode is determined by the video cable used.
5. Connect one end of the power cord to the AC power connector on the back of the monitor, and the other end to an electrical wall outlet. WARNING! To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
Front Panel Controls Table 2-1 Monitor Front Panel Controls Control Function 1 Menu Opens, selects or exits the OSD menu. 2 Minus If the OSD menu is on, press to navigate backward through the OSD menu and decrease adjustment levels. 3 Plus/Input If the OSD menu is on, press to navigate forward through the OSD menu and increase adjustment levels.
Adjusting the Monitor NOTE: 8 Your monitor model may look different than the model in the following illustrations. 1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. 2. Swivel the monitor to the left or right for the best viewing angle.
3. Adjust the monitor’s height to a comfortable position for your individual workstation. The monitor’s top bezel edge should not exceed a height that is parallel to your eye height. A monitor that is positioned low and reclined may be more comfortable for users with corrective lenses. The monitor should be repositioned as you adjust your working posture throughout the work day. NOTE: The monitor stand ships with the display head locked in the lowest height position.
NOTE: To view information on the screen in portrait mode, you can install the HP Display Assistant software included on the software and documentation disc. The position of the OSD menu can also be rotated to portrait mode. To rotate the OSD menu, access the OSD menu by pressing the Menu button on the front panel, select OSD Control from the menu, then select Rotate OSD. Turning on the Monitor 1. Press the power button on the computer to turn it on. 2.
NOTE: You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0 ports on the monitor. Refer to Step 4 in Connecting the Cables on page 5. Removing the Monitor Pedestal Base You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm, or other mounting fixture. CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and the power and signal cables are both disconnected.
Mounting the Monitor The monitor panel can be attached to a wall, swing arm, or other mounting fixture. NOTE: 1. This apparatus is intended to be supported by UL or CSA Listed wall mount bracket. Remove the monitor panel from the pedestal base. Refer to Removing the Monitor Pedestal Base on page 11. CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are required.
Installing a Cable Lock You can secure the monitor to a fixed object with an optional cable lock available from HP.
3 Finding More Information Reference Guides Refer to the HP LCD Monitors Reference Guide included on the disc with your monitor for additional information on: ● Optimizing monitor performance ● Safety and maintenance guidelines ● Installing software from the disc ● Using the OSD menu ● Downloading software from the Web ● Agency regulatory information ● Troubleshooting and recommended solutions to common problems For information on theft deterrence, refer to the HP Display Assistant User Guid
A Technical Specifications NOTE: All specifications represent the typical specifications provided by HP's component manufacturers; actual performance may vary either higher or lower. EliteDisplay E190i Table A-1 EliteDisplay E190i Specifications Display Type LED Backlit IPS Viewable Image Size 47.99 cm diagonal Aspect Ratio 5:4 Tilt -5 to 25° Swivel -180 to 180° Pivot 90° Maximum Weight (Unpacked) 4.8 kg 10.58 lbs Height (highest position) 48.64 cm 19.
Table A-1 EliteDisplay E190i Specifications (continued) Measured Power Consumption: Full Power 28.0 watts Typical Settings 26.0 watts Sleep <0.5 watts Switch Off <0.5 watts Input Terminal One VGA connector, one DVI connector, and one DisplayPort connector (cables included) NOTE: For the latest specifications or additional specifications on this product, go to http://www.hp.com/go/productbulletin/ and search for your specific display model to find the modelspecific QuickSpecs.
Energy Saver Feature The monitors support a reduced power state. The reduced power state will be entered into if the monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and the power light is turned amber. When the monitor is in the reduced power state, the monitor will utilize .5 watts of power.
