HP iPAQ User’s Guide F8T064ukHP Bluetooth™ Hands-Free Headset
Contents Introduction .............................................................................................................................................. 1 Headset Features ..................................................................................................................................... 3 Charging the Headset .............................................................................................................................. 4 Wearing the Headset.......................
Introduction Congratulations on your purchase of the HP iPAQ Bluetooth Hands-Free Headset (the Headset). The Headset is quite light, weighing just about .35 ounces (10g). It has both Headset and Hands-Free profiles for more functions, and is compatible with more Bluetooth wireless technology mobile phones. Read this User’s Guide carefully before you start using the HP iPAQ Bluetooth Hands-Free Headset.
Bluetooth Wireless Technology Bluetooth wireless technology has revolutionized the personal connectivity market by providing seamless freedom from wired connections. It offers a small form-factor, low-cost radio solution providing links between mobile computers, mobile phones, and other portable and handheld devices, and connectivity to the Internet.
Headset Features 3 1. Talk Button: Switches the Headset on/off, answers/ends a call, pairs the Headset with a device, and is used for voice dialing. 2. Volume Up Button: Increases the speaker volume. 3. Volume Down Button: Decreases the speaker volume. 4. LED Indicator: Displays the status of the Headset. 5. Microphone: Picks up external audio. 6. Earpiece: Holds the Headset in the ear. 7. Speaker: Plays incoming audio. 8. Charging Port: Charges the battery.
Charging the Headset The Headset has a rechargeable battery. Before using the Headset for the first time, you have to charge the Headset battery for approximately two hours in order to get a full charge. A fully charged battery provides up to seven hours of talk time and over one week of standby time. When the battery is low, the LED indicator flashes red. The low-battery-warning indication will begin three minutes of talk time before the Headset runs out of power.
To charge the Headset: 1. Connect the retractable USB cable into the car charger or any USB computer, and then plug the other end to the charging base. 2. Place the Headset into the charging base. 3. During charging, the red indicator light on the charging base illuminates. 4. When the battery is fully charged, the indicator light on the charger turns green. 5. You can now remove the Headset from the charging base.
Wearing the Headset The Headset can be worn either on the right or left ear. The earpiece is adjustable, and the 90-degree, rotatable design ensures a snug yet comfortable fit in your ear. To put on the Headset, please follow the instructions as below: 1. Directly put the earpiece into your outer ear canal. 2. Adjust the Headset to fit your ear. 3. The microphone should be positioned toward your mouth. The ear cushion supplied with the Headset provides additional comfort and a better fit.
To attach the ear cushion: 7 1. Hold the Headset firmly. 2. Cover the earpiece with the ear cushion. 3. The ear cushion is attached to the ready-to-wear Headset.
Putting on the Headset 1. Put on the Headset with the earhook behind your ear. 2. Make sure the microphone is pointing toward your mouth.
Switching the Headset On/Off To switch the headset on: 1. Press the “Talk” button for about five seconds until you hear a low tone followed by a high tone. The LED indicator flashes blue four times. 2. The Headset switches on and enters standby mode. The LED indicator continuously flashes blue every three seconds. To switch the headset off: 9 1. Press the “Talk” button for about one second until you hear a high tone followed by a low tone. The LED Indicator flashes red four times. 2.
Pairing the Headset Before using the Headset, you must first pair it with a Bluetooth wireless-technology-enabled device, such as a Bluetooth mobile phone. Pairing is necessary for two Bluetooth devices to connect to each other wirelessly. After creating a paired link, you do not need to repeat the pairing process and the Headset automatically links to the mobile phone when both devices are switched on.
To initiate pairing between the Headset and a Bluetooth mobile phone in close proximity: 11 1. Turn off the Headset. 2. Make certain the mobile phone is switched on. 3. Press the “Talk” button to switch on the Headset and keep the “Talk” button pressed for seven seconds until the LED indicator alternates between blue and red. The Headset is now ready for pairing with the mobile phone. 4. Perform a device discovery from the mobile phone.
Using the Headset Before using the Headset, make sure that (1) the Headset is switched on and connected to a paired Bluetooth mobile phone; (2) the Headset is within 33 feet (10m) of the phone; and (3) the phone’s Bluetooth feature is on (see your phone’s user’s guide). NOTE: The Headset supports both Headset and Hands-Free profiles. Some mobile phones do not support all the functions listed below. Please consult your phone’s user’s guide.
Rejecting a Call When a call comes and you do not want to answer it, you can press the “Talk” button for two seconds to reject the call. Making a Call You can make a call through: A. Voice activation To use voice activation, the mobile phone must support voice dialing. For details on voice dialing, please see your phone’s user’s guide. 13 1. Press the “Talk” button once on your Headset. 2.
B. Dialing a phone number from your mobile phone 1. Dial the phone number from the mobile phone’s keypad. 2. Press the “Talk” button to send the call from your phone. 3. The call automatically transfers to the Headset.
Redialing the Last Number To redial the last phone number, press and hold down the “Volume Down” button for three seconds. Volume Control During a call, you can adjust the Headset speaker volume. An audio tone is played for each volume up and volume down step. To increase the volume, press the “Volume Up” button repeatedly until you reach the desired level. To decrease the volume, press the “Volume Down” button repeatedly until you reach the desired level.
Mute Function To mute the Headset sound during a call, press the “Volume Up” button and the “Volume Down” button for two seconds; you will hear one tone repeated every 20 seconds. Upon activating the mute function, the person on the other side won’t hear you, but you can hear all sound generated from the other side. To turn off the mute function, press the “Volume Up” button or the “Volume Down” button once.
Charging-Base Indicator Status Red LED Charging in process On Green LED Charging complete On Audio Tones Switching on Quick series of 2 tones, low to high Switching off Quick series of 2 tones, high to low Pairing mode 1 tones Incoming call A ring tone at a 2-second interval Mute 1 tone repeated every 20 seconds Turn off mute Single tone Low battery 5 rapid tones every 20 seconds in standby mode NOTE: When using Nokia mobile phones, all sounds generated by the mobile phone automatically
Specifications Standard Compliant with Bluetooth specification v1.1 / v1.2 Chipset BlueCore2-Audio single chipset Profiles Supported Bluetooth Headset & Hands-free profiles Radio Frequency 2402 MHz ~2480 MHz Transmitter Power Class 2 (max 4dBm) Transmission Range Up to 10 meters Receiver Sensitivity -78 dBm Charger Power Supply 5VDC / 200 mA Temperature Operating: -20º C–60º C; Storage: -20º C–60º C; Charging: 0º C–45º C Operation Voltage 3.
Information Users are advised not to make changes or modify the device in any way. Changes or modifications not expressly approved by HP will void the warranty. FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Belkin Corporation Limited 2-Year Product Warranty What this warranty covers. Belkin Corporation warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship. What the period of coverage is. Belkin Corporation warrants the Belkin product for two years. What will we do to correct problems? Product Warranty.
How to get service. To get service for your Belkin product you must take the following steps: 1. Contact Belkin Ltd., Express Business Park, Shipton Way, Rushden, NN10 6GL, United Kingdom, Attn: Customer Service, or call 00 800 2 2355460, within 15 days of the Occurrence. Be prepared to provide the following information: a. The part number of the Belkin product. b. Where you purchased the product. c. When you purchased the product. d. Copy of original receipt. 2.
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN CORPORATION, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
© 2006 HP Corporation. All rights reserved. The product is marketed and supported by Belkin Corporation. For warranty support or technical support, go to www.belkin.com or call Belkin at 00 800 2 2355460. The Bluetooth name and the Bluetooth trademarks are owned by Bluetooth SIG, Inc., and are used by Belkin Corporation under license.
