Quick Configuration Guide for A7000 1xT1 or 1xT1 + DSX-1 Modules 2005-04

ManualsBrandsHP ManualsComputer AccessoriesHP 1-port T1 + DSX-1 dl Module

1

2

3

4

5

6

7

8

9

61195863L1-42B www.procurve.com 1

ProCurve Secure Router

(with 1xT1 or 1xT1 + DSX-1 Modules)

Quick Configuration Guide 5991-2115 April 2005

• Category 5 - UTP cable for connecting the system to the existing network.

• VT100 terminal or PC with VT100 emulation software.

• Serial cable (5184-1894) supplied with the router. This is the console cable used in other

ProCurve switches such as the 5300xl series. The console port is a DB-9 DTE male

connector.

Frame Relay Diagram

PPP over Fractional T1 Connection Diagram

Equipment Required

Note

This quick configuration guide provides step-by-step instructions for configuring

your application. The configuration script is available at the end of this document.

The configuration parameters used in the example outlined in this document are

for instructional purposes only. Please replace all underlined entries (example

)

with your specific parameters to configure your application.

Network Diagrams

Branch Office Corporate HQ

Gateway Router

LAN IP: 10.10.10.1 /24

192.168.72.2 /30

eth 0/1

LAN IP: 10.10.20.7 /24

Network IP: 10.10.20.0

Network IP: 10.10.10.0

DLCI 16

Annex D Signaling

192.168.72.1 /30

FR 1.x

Router

FT1 1-10 (64 kbps)

ProCurve Secure

Router 7102dl/7203dl

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

12

Bkp Bkp

Tx Tx

Rx Rx

Stat

3

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

dl

wide

Branch Office Corporate HQ

Gateway Router

LAN IP: 10.10.10.1 /24

eth 0/1

LAN IP:

t1 1/2

t1 1/1

10.10.20.7 /24

Network IP: 10.10.20.0

Network IP: 10.10.10.0

LAN IP: 192.168.72.2 /30

Router

Point-to-Point T1

DS0s 1-10 Data, 21-24 Voice

PBX

ProCurve Secure

Router 7102dl/7203dl

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

12

Bkp Bkp

Tx Tx

Rx Rx

Stat

3

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

dl

wide

PPP Signaling

RIP V2

192.168.72.1 /30

PPP 1

Summary of content (12 pages)

PAGE 1
ProCurve Secure Router (with 1xT1 or 1xT1 + DSX-1 Modules) Quick Configuration Guide 5991-2115 April 2005 Equipment Required • Category 5 - UTP cable for connecting the system to the existing network. • VT100 terminal or PC with VT100 emulation software. • Serial cable (5184-1894) supplied with the router. This is the console cable used in other ProCurve switches such as the 5300xl series. The console port is a DB-9 DTE male connector.
PAGE 2
Configure the Unit The ProCurve Secure Router may be initially accessed and managed via a console session. Refer to Initiate a Console Session for console session instructions. Initiating a Telnet session requires using a hub and two Ethernet cables (one for the PC and one for the unit). Refer to Configure Telnet Access on page 6 to configure Telnet session settings. Initiate a Console Session 1.
PAGE 3
Configure the T1 Network Interface The following steps specifies the clock source for the T1 network interface(s). Note The 1xT1 + DSX-1 Module supports a single clock source for both interfaces. 1. At the (config)# prompt, enter interface t1 1/1 to activate the interface configuration mode for the T1 network interface. 2. Enter clock source line to configure the router to recover clocking from the T1 network connection.
PAGE 4
Configure the Frame Relay Virtual Interface The following steps outline configuring a Frame Relay virtual interface (labeled 1) using a single DLCI back to the corporate router (defined as DLCI 16). Skip to Configure the Virtual PPP Interface if you are using PPP. 1. At the (config)# prompt, enter interface fr 1 to create a Frame Relay virtual interface labeled 1. 2.
PAGE 5
Configure Static Routes Routes may be assigned either statically or dynamically. Continue with this section to create a static route. Refer to the next section for information on configuring RIP and OSPF dynamic route assignments. Note These examples are based on the network diagrams on page 1. Depending on your network setup, configure static routing on your unit in one of the following ways.
PAGE 6
Scenario 2: Dynamic Routing via RIP 1. At the (config)# prompt, enter router rip to activate the RIP configuration mode. Your prompt should now display (config-rip)#. 2. Enter version 2 to globally define RIP version 2 on all interfaces. 3. Specify the networks: Corporate HQ Router (config-rip)#network 10.10.10.0 255.255.255.0 (config-rip)#network 192.168.72.0 255.255.255.252 Branch Office Router (config-rip)#network 10.10.20.0 255.255.255.0 (config-rip)#network 192.168.72.0 255.255.255.252 4.
PAGE 7
Save the Configuration 1. Verify that the prompt of your unit displays (config)#. 2. Enter exit to leave configuration mode. 3. Enter copy running-config startup-config to save the current configuration to memory. This command may be abbreviated as copy run start. 4. Enter exit to close the configuration session. Complete the Installation The ProCurve Secure Router is now configured and operational. Complete the installation by connecting the appropriate cables to the T1 and Ethernet networks.
PAGE 8
! ! Configure the t1 interface to recover clocking from the T1 ! network connection. clock source line ! ! Create a tdm group (labeled 1) on the T1 interface containing ! 10 DS0s (1-10). tdm group 1 timeslots 1-10 ! ! Activate the interface to pass data. no shutdown ! ! Exit back to the global configuration mode. exit ! ! DSX-1 INTERFACE CONFIGURATION !************************************************************************! ! Enter the interface configuration mode for the DSX-1 port.
PAGE 9
! PVC CONFIGURATION !*************************************************************! ! Create a Frame Relay PVC (with DLCI 16) under Frame Relay ! virtual interface 1. interface fr 1.16 ! ! Your prompt should now display Router(config-fr1.16)#. ! ! Now assign DLCI 16 to the pvc. frame-relay interface-dlci 16 ! ! Next, assign an IP address to this pvc. ip address 192.168.72.1 255.255.255.252 ! ! Activate the interface to pass data. no shutdown ! ! Exit back to the global configuration mode.
PAGE 10
! CONFIGURING STATIC ROUTES - CORP HQ ROUTER - DEFAULT ROUTE !************************************************************************************************! ! Configures the default gateway to the internet router. ! ! Enter the default gateway ip address to the route table. ! This is the address of the internet router. ip route 0.0.0.0 0.0.0.0 10.10.10.
PAGE 11
!*************************************************************! ! Enter the RIP configuration mode. router rip ! ! Your prompt should now display (config-rip)#. ! ! Define RIP version 2. version 2 ! ! Specify the Corp HQ networks. network 10.10.10.0 255.255.255.0 network 192.168.72.0 255.255.255.252 ! ! Specify the Branch Office networks. network 10.10.20.0 255.255.255.0 network 192.168.72.0 255.255.255.252 ! ! Exit back to the global configuration mode.
PAGE 12
! SAVE THE CONFIGURATION !*************************************************************! ! Exit the global configuration mode. exit ! ! Your prompt should now display Router>. ! ! Save the current configuration to memory. copy running-config startup-config ! ! Exit to close the configuration session. exit ! ! End script Copyright 2005 Hewlett-Packard Development Company, LP. The information contained herein is subject to change without notice.