Brocade iSCSI Gateway Service Administrator's Guide (53-1000603-01, October 2007)

iSCSI Gateway Service Administrator’s Guide 41
53-1000603-01
Creating an iSCSI FC zone
4
You should add all virtual initiators for each blade to the zone. (The nsShow command example
continues on the following page.)
(The nsShow example continued)
N 012b00; 3;50:06:06:9e:00:15:63:18;50:06:06:9e:00:15:63:19; na
FC4s: FCP
PortSymb: [23] "iSCSI Virtual Initiator"
NodeSymb: [51] "IPAddr: 30.0.127.33 Slot/Port: 3/ge3 Logical pn: 43"
Fabric Port Name: 00:00:00:00:00:00:00:00
Permanent Port Name: 50:06:06:9e:00:15:63:18
Port Index: 43
Share Area: No
Device Shared in Other AD: No
N 012c00; 3;50:06:06:9e:00:15:63:20;50:06:06:9e:00:15:63:21; na
FC4s: FCP
PortSymb: [23] "iSCSI Virtual Initiator"
NodeSymb: [51] "IPAddr: 30.0.127.34 Slot/Port: 3/ge4 Logical pn: 44"
Fabric Port Name: 00:00:00:00:00:00:00:00
Permanent Port Name: 50:06:06:9e:00:15:63:20
Port Index: 44
Share Area: No
Device Shared in Other AD: No
N 012d00; 3;50:06:06:9e:00:15:63:28;50:06:06:9e:00:15:63:29; na
FC4s: FCP
PortSymb: [23] "iSCSI Virtual Initiator"
NodeSymb: [51] "IPAddr: 30.0.127.35 Slot/Port: 3/ge5 Logical pn: 45"
Fabric Port Name: 00:00:00:00:00:00:00:00
Permanent Port Name: 50:06:06:9e:00:15:63:28
Port Index: 45
Share Area: No
Device Shared in Other AD: No
N 012e00; 3;50:06:06:9e:00:15:63:30;50:06:06:9e:00:15:63:31; na
FC4s: FCP
PortSymb: [23] "iSCSI Virtual Initiator"
NodeSymb: [51] "IPAddr: 30.0.127.36 Slot/Port: 3/ge6 Logical pn: 46"
Fabric Port Name: 00:00:00:00:00:00:00:00
Permanent Port Name: 50:06:06:9e:00:15:63:30
Port Index: 46
Share Area: No
Device Shared in Other AD: No
N 012f00; 3;50:06:06:9e:00:15:63:38;50:06:06:9e:00:15:63:39; na
FC4s: FCP
PortSymb: [23] "iSCSI Virtual Initiator"
NodeSymb: [51] "IPAddr: 30.0.127.37 Slot/Port: 3/ge7 Logical pn: 47"
Fabric Port Name: 00:00:00:00:00:00:00:00
Permanent Port Name: 50:06:06:9e:00:15:63:38
Port Index: 47
Share Area: No
Device Shared in Other AD: No
The Local Name Server has 11 entries }
To display the FC target WWNs for switches other than the Brocade 48000, telnet into that
switch and run the nsShow command.