HP Designjet L25500 printer series Site preparation guide (Second edition)
Legal notices © 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Table of contents 1 Overview Introduction ............................................................................................................................. 1 Customer responsibility ............................................................................................................. 1 Installation time schedule ........................................................................................................... 1 2 Site preparation requirements Physical space requirements ........
iv ENWW
Overview Overview 1 Introduction This Site preparation guide should be used for HP Designjet L25500 printers, both 42 inch and 60 inch. Specifications and requirements are stated for both printer widths wherever necessary. Your printer is supplied ready to use after a few simple installation procedures described in detail in the Assembly instructions.
2 Site preparation requirements Physical space requirements Unloading route The route between the unloading area of the printer and the installation site, including any corridors and doorways through which the printer must be transported, is important to proper site preparation and must be checked before the arrival of the printer. This pathway must be clear when the printer arrives. Table 2-1 42-in printer physical specifications Printer Packaging Length 78 in (1.99 m) 87.91 in (2.23 m) Width 27.
Environmental specifications Requirements These environmental conditions must be kept within the specified ranges to ensure the correct operation of the printer. Failure to do so may cause print-quality problems or damage sensitive electronic components.
NOTE: Maintaining positive air pressure in the print production room will help prevent dust from entering the room. RIP workstation characteristics The RIP computer and RIP software must be provided by the customer. Each RIP has specific requirements. Check with your RIP vendor to find out the requirements for the PC that you'll be using for the RIP station. Make sure that the RIP station is fully functional and ready for installation.
Table 2-4 Single phase line specifications (continued) 60-in printer 60–in printer (Japan only) 42-in printer Maximum power consumption 4.8 kW (overall consumption for both power cords) 4.8 kW (overall consumption for both power cords) 3.5 kW (overall consumption for both power cords) Maximum load current (per power cord) 15 A 15 A 13 A Active power consumption 2.6 kW 2.6 kW 1.
Figure 2-1 Electrical configuration diagram Wall receptacles and power cords Two power cords are provided with your printer, according to the printer's electrical specifications. If those cords do not reach your PDU and/or UPS, a certified electrician must install suitable extension cables on the day of installation. To make sure you have the right wall socket outlets (wall receptacles) ready for installation, check the following: 1. The wall socket outlets must be suitable for printer input ratings.
Table 2-6 60 inch printer power cord specifications (continued) Country HP Part Number * Length Plug type Plug International 8120-6897 4.5 m IEC 60309, 240 V, 16 A, 2L+PE International – other 8120-6895 4.5 m Stripped end termination, 240 V, 1.5 mm² cross sectional area Requirements WARNING! A qualified electrician must attach a suitable plug according to local laws where the printer is installed, and to the printer's electrical requirements.
Table 2-7 42 inch printer power cord specifications (continued) Country HP Part Number * Length Plug type Continental Europe, Korea, Indonesia, Russia 8120-6352 2.5 m CEE 7-VII India 8121-1074 2.5 m IS 1293 Taiwan 8121-1033 4.5 m CNS 690 UK, Hong Kong, Singapore 8120–6898 4.5 m BS 1363/A (13A fused) Denmark 8121-1077 2.5 m DK 2-5A Israel 8121-1010 2.5 m SI 32 South Africa 8121-0915 2.5 m SABS 164 Switzerland, Liechtenstein 8120-6897 4.
NOTE: Place the wall receptacle close enough to the printer so the plug can be plugged and unplugged easily. Powerline disturbances ● In order to ensure optimum performance and reliability, your printer should be protected from variations in line voltage. Lightning, line faults or the switching of lighting or machinery can generate line transients that far exceed the peak value of the applied voltage. If not reduced, these microsecond pulses can disrupt system operation and damage the printer.
3 Site preparation checklist Safety requirements Yes No Comments Yes No Comments Is there an emergency exit in the print production area, with easy access and free from any obstruction? Electrical installation requirements Is the electrician aware of all requirements and specifications highlighted in this guide? (Required) Is the single-phase line voltage inside the specified voltage range? ● 42-in printer: 200–240 V~ (–10%, +6%) ● 60-in printer: 220–240 V~ (–10%, +6%) (Required) Specify nom
Electrical installation requirements Yes No Are the wall receptacles (wall sockets) placed close enough to the printer that the plugs can be plugged and unplugged easily? (Required) NOTE: The power cord length is 14.8 ft (4.5 m) for 60-in printers, and 8.2 ft (2.5 m) for 42-in printers.
