HP Comware 5 Debug Manual Vol 1
// LSPM deleted an LSP.
*0.92036640 PE1 LSPM/8/LSPM POLICY:
Route Doesnot Satisfy Policy!. Sig Prot is informed.
// The route did not satisfy the policy. LSPM notified the signaling module.
*0.92036640 PE1 LSPM/8/LSPM POLICY:
Calling Signalling protocol for VRF:0 Dst Addr:0x8c030303 Dst Mask:0xffffffff NextHop:
0x8c0c0102 If Index: 0x300010 Event: 13
// LSPM called the signaling protocol.
*0.92036640 PE1 LSPM/8/LSPM POLICY:
Route Doesnot Satisfy Policy!. Sig Prot is informed.
// The route did not satisfy the policy. LSPM notified the signaling module.
*0.92036640 PE1 LSPM/8/LSPM POLICY:
Calling Signalling protocol for VRF:0 Dst Addr:0x8c020202 Dst Mask:0xffffffff NextHop:
0x8c0c0102 If Index: 0x300010 Event: 13
// LSPM called the signaling protocol.
#Dec 23 10:12:23:365 2005 PE1 LDP/5/SessionUp: Session(140.2.2.2:0. public Instance)'s
state change to Up
// The session came up again.
*0.92041801 PE1 LSPM/8/LSPM POLICY:
Received Route Add message, VRF:0 Destination: 0x8c010101 Destination mask: 0xffffffff
Nexthop: 0x7f000001 IfIndex:1376256.
// LSPM received a route ADD message.
*0.92041801 PE1 LSPM/8/LSPM POLICY:
Calling Signalling protocol for VRF:0 Dst Addr:0x8c010101 Dst Mask:0xffffffff NextHop:
0x7f000001 If Index: 0x150000 Event: 1
// LSPM called the signaling protocol for processing.
*0.92041801 PE1 LSPM/8/LSPM POLICY:
Route added successfully
// LSPM added the route successfully.
*0.92042024 PE1 LSPM/8/LSPM POLICY:
LSP added, VRF:0 Destination: 0x8c010101 Destination mask: 0xffffffff Nexthop:0x7f000001
IfIndex:0x150000 LSPIndex:0x2446.
// LSPM added an LS P.
*0.92066067 PE1 LSPM/8/LSPM POLICY:
LSP added, VRF:0 Destination: 0x8c020202 Destination mask: 0xffffffff Nexthop:0x8c0c0102
IfIndex:0x300010 LSPIndex:0x2447.
// LSPM added an LS P.
*0.92066083 PE1 LSPM/8/LSPM POLICY:
LSP added, VRF:0 Destination: 0x8c030303 Destination mask: 0xffffffff Nexthop:0x8c0c0102
IfIndex:0x300010 LSPIndex:0x2448.
// LSPM added an LS P.
# Enable debugging for MPLS management process on one router (PE 1, in this example). When MPLS
LDP is reset on the other router, output similar to the following example is generated:
<PE1> debugging mpls management process
<PE1>
152