HP Comware 5 Debug Manual Vol 1

ManualsBrandsHP ManualsNetwork HardwareHP HSR68xx Configure-to-Order Router Solution

171

172

173

174

175

176

177

178

179

180

*Jan 4 09:30:09:642 2007 Sysname BFD/7/SCM:Interface of the session doesn't exist, create

*Jan 4 09:30:09:642 2007 Sysname BFD/7/SCM:Bfd-int[Dialer0], Oper: Create

*Jan 4 09:30:09:658 2007 Sysname BFD/7/SCM:Create session entry

*Jan 4 09:30:09:658 2007 Sysname BFD/7/SCM:Allocate global resource to a session

*Jan 4 09:30:09:658 2007 Sysname BFD/7/SCM:Add session to bfd interface

*Jan 4 09:30:09:658 2007 Sysname BFD/7/SCM:Add session to IP hash table

*Jan 4 09:30:09:658 2007 Sysname BFD/7/SCM:Send first echo packet to peer

// The session interface did not exist, so interface Dialer0 and the session entry were created first, and

global resources were assigned to the session, and then the first Echo packet was sent to the peer.

*Jan 4 09:32:43:804 2007 Sysname BFD/7/SCM:Sess[6.6.66.6/6.6.66.8,Dia0,Echo], Oper:

Delete application(STATIC)

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:No application in session, delete

session[6.6.66.6/6.6.66.8,Dia0,Echo]

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:Sess[6.6.66.6/6.6.66.8,Dia0,Echo], Oper:

Delete

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:Delete send-echo-packet timer

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:Delete session entry

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:Delete session from IP hash table

*Jan 4 09:32:43:820 2007 Sysname BFD/7/SCM:Delete session from bfd interface

*Jan 4 09:32:43:835 2007 Sysname BFD/7/SCM:No session under bfd-int[Dialer0] with default

configuration, delete bfd-if

*Jan 4 09:32:43:835 2007 Sysname BFD/7/SCM:Bfd-if[Dialer0], Oper: Delete

//The BFD session with source address 6.6.66.6, destination address 6.6.66.8, interface Dialer0, and

working mode Echo was deleted, and the Echo packet send timer and session entry were deleted.

debugging bfd timer

Use debugging bfd timer to enable BFD timer event debugging.

Use undo debugging bfd timer to disable BFD timer event debugging.

Syntax

debugging bfd timer

undo debugging bfd timer

Default

BFD timer event debugging is disabled.

Views

User view

Default command level

1: Monitor level

Examples

# Enable BFD timer event debugging on a BFD-capable device.

<Sysname> debugging bfd timer

*Jan 4 09:34:24:54 2007 Sysname BFD/7/TMR:Create send-echo-packet timer

*Jan 4 09:34:24:54 2007 Sysname BFD/7/TMR:Send-echo-packet timer[1000ms] of

session[6.6.66.6/6.6.66.8,Dia0,Echo] is created

174