R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
145
BERT state:(stopped)
E3 2/0/0 CE1 5 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 6 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 7 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 8 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 9 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 10 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 11 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 12 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 13 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 14 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 15 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none
BERT state:(stopped)
E3 2/0/0 CE1 16 is up
Frame-format NO-CRC4, clock slave, loopback not set
Receiver alarm state is none