R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
162
Field Descri
p
tion
Receiver alarm state
Type of the received alarm: none, LOS, LOF, RAI, or AIS.
If a LOS, LOF, AIS was received, RAI would be sent and the screen
displayed "Transmitter is sending RAI" instead.
MDL state MDL state.
No message is sent now.
No MDL message is being sent. If an MDL message, path or
idle-signal for example, was being sent, the screen would display
"Message sent now: path. idle signal."
Message data elements MDL data elements.
EIC: line, LIC: line, FIC: line, UNIT: line
EIC, LIC, FIC, and UNIT are four elements present in all types of MDL
messages. Their values are user configurable and default to line.
FI: line, PORT_NO: line, GEN_NO: line
FI is found in MDL path messages, PORT_NO in MDL idle signal
messages, and GEN_NO in MDL test signal messages. Their values
are user configurable and default to line.
Periodical detection
State of periodical detection of MDL, disabled by default at the
startup of the router.
When the function is enabled, the screen displays:
Periodical detection is enabled.
No message was received.
When MDL messages are detected, the screen displays:
Message received now: path.idle signal.
EIC: line, LIC: line, FIC: line, UNIT: line.
path/FI: line.
idle Signal/PORT_NO: line .
FEAC state FEAC state.
No code is sent now. DS3 Line Loop
Back Deactivate was last sent.
No FEAC signal is sent. The FEAC signal sent last time is DS3 Line
Loop Back Deactivate.
Periodical detection is enabled, no
code received now.
Periodical detection of FEAC is enabled. This is the default applied
at the startup of the router.
No FEAC signal is received now.
DS3 Line Loop Back Deactivate last
received.
The FEAC signal received last time is DS3 Line Loop Back
Deactivate.
BERT state:(stopped, not completed) BERT state: completed, stopped (not completed), or running.
Test pattern: 2^7, Status: Not Sync,
Sync Detected: 0
Test pattern in use (such as 2^7, 2^11, 2^15, and QRSS), 2^7 in
this sample output; synchronization state, and the number of
detected synchronizations.
Time: 0 minute(s), Time past: 0 minute(s)
Duration of the BERT test and time that has elapsed.
Bit errors (since test started): 0 bits Number of bit errors received since start of the BERT test.
Bits received (since test started) Number of bits received since start of the BERT test.
Bit errors (since latest sync) Number of bit errors received since last synchronization.
Bits received (since latest sync) Number of bits received since last synchronization.