R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
10
Field Description
Last clearing of counters
Time when the reset counters interface command was last used to clear
statistics on the subinterface.
If the command was never used since the device was started, this field
displays Never.
Input Input packet statistics.
Output Output packet statistics.
# Display detailed information about Layer 2 interface GigabitEthernet 4/0/1.
<Sysname> display interface gigabitethernet 4/0/1
GigabitEthernet4/0/1 current state: UP
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 0000-000f-0007
Description: GigabitEthernet4/0/1 Interface
Loopback is not set
Media type is twisted pair
port hardware type is 1000_BASE_T
100Mbps-speed mode, half-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 1536
Broadcast MAX-ratio: 100%
Unicast MAX-ratio: 100%
Multicast MAX-ratio: 100%
Allow jumbo frame to pass
PVID: 999
Mdi type: auto
Port link-type: access
Tagged VLAN ID : none
Untagged VLAN ID : 999
Port priority: 0
Last clearing of counters: Never
Peak value of input: 0 bytes/sec, at 2003-09-16 16:25:33
Peak value of output: 0 bytes/sec, at 2003-09-16 16:25:33
Last 300 seconds input: 0 packets/sec 74 bytes/sec 0%
Last 300 seconds output: 0 packets/sec 12 bytes/sec 0%
Input (total): 21322 packets, 1748554 bytes
- unicasts, - broadcasts, - multicasts, - pauses
Input (normal): 21322 packets, - bytes
1268 unicasts, 7560 broadcasts, 12494 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, - throttles
0 CRC, - frame, - overruns, - aborts
- ignored, - parity errors
Output (total): 1502 packets, 138924 bytes
- unicasts, 2 broadcasts, 406 multicasts, 0 pauses
Output (normal): - packets, - bytes
1094 unicasts, - broadcasts, - multicasts, - pauses
Output: 3 output errors, - underruns, - buffer failures