R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
259
If you specify the null keyword, this command displays information about interface Null 0 with or without
the 0 keyword, because the device supports only one null interface.
Examples
# Display detailed information about null interface Null 0.
<Sysname> display interface null 0
NULL0 current state :UP
Line protocol current state :UP (spoofing)
Description : NULL0 Interface
The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
Physical is NULL DEV
Last clearing of counters: Never
Last 300 seconds input: 0 bytes/sec, 0 bits/sec, 0 packets/sec
Last 300 seconds output: 0 bytes/sec, 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 drops
0 packets output, 0 bytes, 0 drops
# Display brief information about interface Null 0.
<Sysname> display interface null 0 brief
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Main IP Description
NULL0 UP UP(s) --
See Table 33 for the display interface null command output.
Related commands
interface null
interface loopback
Use interface loopback to create a loopback interface or enter loopback interface view.
Use undo interface loopback to remove a loopback interface.
Syntax
interface loopback interface-number
undo interface loopback interface-number
Views
System view
Default command level
2: System level
Parameters
interface-number: Specifies a loopback interface by its number in the range of 0 to 1023.
Examples
# Create interface loopback 5.