R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
26
interface-list: Specifies an Ethernet interface list, in the format of interface-type interface-number [ to
interface-type interface-number ] &<1-10>, where &<1-10> indicates that you can specify up to 10
interfaces or interface ranges.
Usage guidelines
Depending on the hardware structure of interface cards, some interfaces can operate only as Layer 2
Ethernet interfaces (in bridge mode), some can operate only as Layer 3 Ethernet interfaces (in route
mode), and others can operate as either Layer 2 or Layer 3 Ethernet interfaces (you can set the link mode
to bridge or route).
Configuring the port link-mode interface-list command in system view and configuring the port
link-mode command in Ethernet interface view lead to the same result. The difference is that the former
changes the link mode of multiple Ethernet interfaces in batch, and the latter changes the link mode of
one Ethernet interface at a time.
After you change the link mode of an Ethernet interface, all settings of the Ethernet interface are restored
to their defaults under the new link mode.
The link mode configuration for an Ethernet interface in system view and that in interface view supersede
each other, and the one configured last takes effect.
Examples
# Configure GigabitEthernet 4/0/1 through GigabitEthernet 4/0/5 to operate in bridge mode.
<Sysname> system-view
[Sysname] port link-mode bridge GigabitEthernet 4/0/1 to GigabitEthernet 4/0/5
# Configure GigabitEthernet 4/0/1 through GigabitEthernet 4/0/5 to operate in route mode.
<Sysname> system-view
[Sysname] port link-mode route gigabitethernet 4/0/1 to gigabitethernet 4/0/5
port-mode
Use port-mode to configure a 10-GE interface to operate in LAN or WAN mode.
Use undo port-mode to restore the default.
Syntax
port-mode { lan | wan }
undo port-mode
Default
A 10-GE interface operates in LAN mode.
Views
Ten-GigabitEthernet interface view
Default command level
2: System level
Parameters
lan: Configures the interface to operate in LAN mode. A port operating in LAN mode transmits Ethernet
packets and connects an Ethernet network.
wan: Configures the interface to operate in WAN mode. A port operating in WAN mode transmits SDH
packets and connects an SDH network. In addition, it supports only point-to-point packet transmission.