R3303-HP HSR6800 Routers Interface Command Reference
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- General Ethernet interface and subinterface configuration commands
- bandwidth
- combo enable
- description
- display counters
- display counters rate
- display interface
- display packet-drop interface
- display packet-drop summary
- duplex
- flag sdh
- flow-interval
- interface
- ip fast-forwarding
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- port-mode
- reset counters interface
- reset packet-drop interface
- shutdown
- speed
- sub-interface rate-statistic
- Layer 2 Ethernet interface and subinterface configuration commands
- broadcast-suppression
- display loopback-detection
- display port-group manual
- display storm-constrain
- flow-interval
- group-member
- jumboframe enable
- loopback-detection action
- loopback-detection control enable
- loopback-detection enable
- loopback-detection interval-time
- loopback-detection multi-port-mode enable
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- speed auto
- storm-constrain
- storm-constrain control
- storm-constrain enable log
- storm-constrain enable trap
- storm-constrain interval
- unicast-suppression
- virtual-cable-test
- Layer 3 Ethernet interface and subinterface configuration commands
- General Ethernet interface and subinterface configuration commands
- ATM interface configuration commands
- WAN interface configuration commands
- Common WAN interface configuration commands
- Serial interface configuration commands
- Basic CE1 interface configuration commands
- Alarm
- cable (CE1 interface)
- channel-set (CE1 interface)
- clock (CE1 interface)
- clock-change auto
- code (CE1 interface)
- controller e1
- crc
- data-coding (CE1 interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- frame-format (CE1 interface)
- idlecode (CE1 interface)
- itf (CE1 interface)
- loopback (CE1 interface)
- reset counters controller e1
- using (CE1 interface)
- Basic CT1 interface configuration commands
- alarm (CT1 interface)
- alarm-threshold
- bert (CT1 interface)
- cable (CT1 interface)
- channel-set (CT1 interface)
- clock (CT1 interface)
- code (CT1 interface)
- controller t1
- crc
- data-coding (CT1 interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- fdl
- frame-format (CT1 interface)
- idlecode (CT1 interface)
- itf (CT1 interface)
- loopback (CT1 interface)
- reset counters controller t1
- sendloopcode
- E1-F interface configuration commands
- T1-F interface configuration commands
- Basic CE3 interface configuration commands
- Basic CT3 interface configuration commands
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- link-delay
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- description
- display controller cpos
- display controller cpos e1
- display controller cpos e3
- display controller cpos t1
- display controller cpos t3
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- e3 set clock
- e3 set loopback
- e3 set national-bit
- e3 shutdown
- fe3
- flag
- flag vc-3
- flag vc-4
- frame-format
- ft3
- link-delay
- loopback
- multiplex mode
- ppp mp soft-binding
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- t3 set alarm
- t3 set bert pattern
- t3 set clock
- t3 set feac
- t3 set frame-format
- t3 set loopback
- t3 set mdl
- threshold
- using e3
- using t3
- E-CPOS interace configuration commands
- Loopback and null interface configuration commands
- Support and other resources
- Index
63
WAN interface configuration commands
Common WAN interface configuration commands
bandwidth
Use bandwidth to set the intended bandwidth for the interface.
Use undo bandwidth to restore the default.
Syntax
bandwidth bandwidth-value
undo bandwidth
Views
Serial interface view, E1-F interface view, T1-F interface view, CE3 interface view, CT3 interface view,
CE1 interface view, CT1 interface view
Default command level
2: System level
Parameters
bandwidth-value: Intended bandwidth for the interface, ranging from 1 to 4,294,967,295 kbps.
Usage guidelines
You can obtain the intended bandwidth of an interface by querying the ifspeed value of the MIB node
with third-party software.
The intended bandwidth is used for bandwidth monitoring of the network management, but does not
affect the actual bandwidth of the interface.
Examples
# Set the intended bandwidth to 50 kbps for interface Serial 2/1/1.
<Sysname> system-view
[Sysname] interface serial 2/1/1
[Sysname-Serial2/1/1] bandwidth 50
description
Use description to set the description for the interface.
Use undo description to restore the default.
Syntax
description text
undo description