HP StorageWorks LUN Configuration and Security Manager XP user guide for the XP12000/XP10000/SVS200 LUN Manager and Volume Manager Part number: T1714–96015 Seventh edition: September, 2007
Legal and notice information © Copyright 1999, 2007 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1 Overview of LUN Manager . . . . . . . . . . . . . . . . . . . . . 17 2 Preparing to use LUN Manager . . . . . . . . . . . . . . . . . . 57 Intended audience . . . . . . . Prerequisites . . . . . . . . . Related documentation . . . . . Document conventions and symbols HP technical support . . . . . . Subscription service . . . . . . HP websites . . . . . . . . . . Documentation feedback . . . . . . . . . . . . . . . .
WWN name table . . . . . . iSCSI name table . . . . . . LDEV table . . . . . . . . . . . Buttons . . . . . . . . . . . . . Port pane . . . . . . . . . . . . . . Package tree . . . . . . . . . . Fibre folder . . . . . . . . . iSCSI folder . . . . . . . . . NAS folder . . . . . . . . . Port table . . . . . . . . . . . . iSCSI Function box . . . . . . . . Change Port Mode box . . . . . . CHN list . . . . . . . . . . . . Buttons . . . . . . . . . . . . . Authentication pane . . . . . . . . . Port tree . . . . .
Using LUN security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabling LUN security . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disabling LUN security . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring arrays for using RAID Manager XP commands . . . . . . . . . . . . . . . Specifying logical devices as command devices . . . . . . . . . . . . . . . . . Protecting logical devices from RAID Manager XP commands . . . . . . . . . . . .
Volume Manager operations using a path-defined LDEV Overview of Custom Volume Size . . . . . . . . . . . . . CVS function . . . . . . . . . . . . . . . . . . . . Parity group configuration . . . . . . . . . . . . . . . Volume to Space function . . . . . . . . . . . . . . . Install CV function . . . . . . . . . . . . . . . . . . Calculating CV capacity for mainframe systems . . . Calculating CV capacity for open systems . . . . . . Volume Initialize and Make Volume functions . . . . . . SSID requirements . .
Volume to Space Confirmation pane . . . . . . . . . . . . . . Install CV pane (1) . . . . . . . . . . . . . . . . . . . . . . Install CV pane (1) for OPEN-V . . . . . . . . . . . . . . . Install CV pane (1) for other than OPEN-V . . . . . . . . . . Install CV pane (2) . . . . . . . . . . . . . . . . . . . . . . Install CV pane (3) . . . . . . . . . . . . . . . . . . . . . . Install CV pane (4) . . . . . . . . . . . . . . . . . . . . . . Make Volume pane . . . . . . . . . . . . . . . . . . . . .
Figures 1 ..Array integrating Fibre Channel, iSCSI, and NAS environments . . . . . . . . . . . . 18 2 ..LU path configuration in Fibre Channel environments . . . . . . . . . . . . . . . . 20 3 ..LU path configuration in iSCSI environments . . . . . . . . . . . . . . . . . . . . 22 4 ..LU path configuration in NAS environments . . . . . . . . . . . . . . . . . . . . 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6 ..Disabling LUN security . . . . . . . . . . . . . . . . . . . . .
38 ..Add New iSCSI Target pane (Option selected) . . . . . . . . . . . . . . . . . . . 86 39 ..Add New WWN dialog box (when registering a host that was previously connected to the array) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 40 ..Add New WWN dialog box (registering a host that has never been connected to the array) 88 41 ..Add New iSCSI name pane (registering a host that was previously connected to the array) 89 42 ..
78 ..Overview of Make Volume function . . . . . . . . . . . . . . . . . . . . . . . . 79 ..Parity group configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 144 80 ..Virtual CVS volume configuration . . . . . . . . . . . . . . . . . . . . . . . . . 144 81 ..Icons showing Unlocked status and View mode . . . . . . . . . . . . . . . . . . . 157 82 ..Mode changing confirmation message . . . . . . . . . . . . . . . . . . . . . . 157 83 ..Icons showing Locked status and Modify mode .
Tables 1 ..Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ..Available addresses for Fibre Channel ports . . . . . . . . . . . . . . . . . . . . 14 28 3 ..Port serial numbers and names (4-port channel adapters) . . . . . . . . . . . . . . 31 4 ..Port serial numbers and names (8-port channel adapter) . . . . . . . . . . . . . . . 34 5 ..Port serial numbers and names (16-port channel adapter) . . . . . . . . . . . . . . 38 6 ..
39 ..Set SSID tree icons (Install CV) . . . . . . . . . . . . . . . . . . . . . . . . . . 183 40 ..Set SSID tree icons (Make Volume) . . . . . . . . . . . . . . . . . . . . . . . . 191 41 ..Set SSID tree icons (Volume Initialize) . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about: • LUN Manager (Part 1) • Volume Manager (Part 2) Intended audience This guide is intended for customers and HP-authorized service providers with knowledge of: • Disk array hardware and software • Data processing and RAID storage subsystems and their basic functions and utilities NOTE: The functions described in this manual may be limited, depending on your assigned level of user access.
Document conventions and symbols Table 1 Document conventions Convention Element Blue text: Table 1 Cross-reference links and e-mail addresses Blue, underlined text: http://www.hp.
• Detailed questions Subscription service HP recommends that you register your product at the Subscriber's Choice for Business website: http://www.hp.com/go/e-updates After registering, you will receive e-mail notification of product enhancements, new driver versions, firmware updates, and other product resources. HP websites For additional information, see the following HP websites: • • • • http://www.hp.com http://www.hp.com/go/storage http://www.hp.com/service_locator http://www.hp.
About this guide
1 Overview of LUN Manager The XP12000/XP10000/SVS200 arrays integrate the following storage environments to provide advanced storage solutions: • Fibre Channel: Fibre Channel is a protocol that enables fast data transfers and can be used for configuring a storage area network (SAN). To use an array as SAN storage, you should attach host servers to the array's Fibre Channel ports.
Figure 1 Array integrating Fibre Channel, iSCSI, and NAS environments You can connect the array to open-system server hosts on different platforms (for example, UNIX and PC servers). To configure a system that includes open-system hosts and an array, you must use LUN Manager to configure logical volumes and ports. One of the important tasks with logical volume configuration is to define I/O paths from hosts to logical volumes.
Configuring LU paths in Fibre Channel environments After open-system hosts and the array are physically connected by cables, hubs, and so on, you must use LUN Manager to establish I/O paths between the hosts and logical volumes. This defines which host can access which logical volume. Logical volumes that open-system hosts can access are referred to as logical units (LUs). Paths between open-system hosts and LUs are referred to as LU paths.
Figure 2 LU path configuration in Fibre Channel environments Use LUN Manager to define paths between a single server host and multiple LUs. In Figure 2, both hosts in the hg-lnx host group can access the three LUs. Use LUN Manager to define paths between multiple server hosts and a single LU. In Figure 2, the LU identified by CU-LDEV number 00:00 is accessible from both hosts belonging to the hg-lnx host group. In Figure 2, LUs associated with the hg-lnx host group are addressed by numbers 0000 to 0002.
NOTE: • In Fibre Channel environments, you can define up to 1,024 LU paths for one host group and up to 1,024 LU paths for one port. • You cannot define LU paths to LUN On-Demand volumes. • You cannot define LU paths to volumes reserved by Auto LUN XP. • You can create up to 255 host groups for one Fibre Channel port. • You cannot define LU paths to journal volumes. • You cannot define LU paths to pool volumes.
Figure 3 LU path configuration in iSCSI environments Use LUN Manager to define paths between a single server host and multiple LUs. In Figure 3, both hosts in the hg-lnx iSCSI target can access the three LUs. Use LUN Manager to define paths between multiple server hosts and a single LU. In Figure 3, the LU identified by CU-LDEV number 00:00 is accessible from both hosts belonging to the hg-lnx iSCSI target. In Figure 3, LUs associated with the hg-lnx iSCSI target are addressed by numbers 0 to 2.
• Defining and viewing alternate paths For more information about LUN configuration, see Overview of Volume Manager and Custom Volume Size. NOTE: • In iSCSI environments, you can define up to 1,024 LU paths for one iSCSI target and up to 1,024 LU paths for one port. • You cannot define LU paths to LUN On-Demand volumes. • You cannot define LU paths to volumes reserved by Auto LUN XP. • You can create up to 64 iSCSI targets for one Fibre Channel port. • You cannot define LU paths to journal volumes.
Figure 4 LU path configuration in NAS environments Configuring LUN security To protect mission-critical data in the array from illegal access, you must apply security policies to logical volumes. Use LUN Manager to enable LUN security on ports to safeguard LUs from illegal access. NOTE: • You cannot apply LUN security to NAS ports. • If a port has the External attribute, you cannot apply LUN security to the port.
If LUN security is enabled, host groups affect which host can access which LUs. Hosts can only access LUs associated with the host group the hosts belong to. Hosts cannot access LUs associated with other host groups. For example, hosts in the hp-ux host group cannot access LUs associated with the Windows host group. Also, hosts in the Windows host group cannot access LUs associated with the hp-ux host group. In Figure 5, LUN security is enabled on port CL1-A.
By default, LUN security is disabled on each port. When you configure the system, you must enable LUN security on each port to which hosts are connected. For more information, see Using LUN security. Configuring LUs for use by RAID Manager XP System administrators can enter RAID Manager XP commands from open-system hosts to perform Continuous Access XP and Business Copy XP operations on logical devices. For example, administrators can enter RAID Manager XP commands to create or split pairs.
Figure 7 FC-AL and Point-to-point topologies When configuring the system, use the LUN Manager pane to specify whether the hosts and array are connected by a fabric switch. If you use a fabric switch, you must specify FC-AL or point-to-point in the LUN Manager pane (by default, FC-AL is specified). If you use a fabric switch, see the fabric switch's documentation to learn whether you should use FC-AL or point-to-point. Some fabric switches require that you specify point-to-point to get the system running.
Table 2 Available addresses for Fibre Channel ports Port address (AL-PA) Loop ID Port address (AL-PA) Loop ID Port address (AL-PA) Loop ID Port address (AL-PA) Loop ID EF 0 B2 32 72 64 3A 96 E8 1 B1 33 71 65 39 97 E4 2 AE 34 6E 66 36 98 E2 3 AD 35 6D 67 35 99 E1 4 AC 36 6C 68 34 100 E0 5 AB 37 6B 69 33 101 DC 6 AA 38 6A 70 32 102 DA 7 A9 39 69 71 31 103 D9 8 A7 40 67 72 2E 104 D6 9 A6 41 66 73 2D 105 D5 10 A5 42 65
ports where a larger amount of data is transferred, you can optimize system performance. If you set a slower data transfer speed for ports where a smaller amount of data is transferred, you can also optimize performance. For more information, see Specifying a Fibre Channel port's data transfer speed. Standard, High Speed, and Initiator/External MIX modes Channel adapter boards have built-in ports used for connecting hosts and an array.
Figure 8 Ports in High Speed or Initiator/External MIX mode If High Speed mode is applied to the four ports in a port block, only two of the ports can be used for connecting the host. These two ports can exclusively use channel processors and fibre optic processors (FOPs) that would otherwise be reserved for the other two ports. Therefore, system performance improves. By balancing workloads on processors, you can expect a greater improvement in system performance.
NOTE: • Sometimes Standard, High Speed, and Initiator/External MIX modes are collectively referred to as Fibre PCB modes. PCB is an acronym for printed circuit board. The array documentation sometimes uses the term PCB when referring to a channel adapter, which is a printed circuit board used for connecting hosts and an array. • Storage partition administrators cannot apply High Speed or Initiator/External MIX mode.
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 29 – – 157 – – 30 – – 158 – – 31 – – 159 – – 32 CL1-J CL1-J 160 CL2-J CL2-J 33 CL3-J CL3-J [1-J 2nd] 161 CL4-J CL4-J [2-J 2nd] 34 – – 162 – – 35 – – 163 – – 36 – – 164 – – 37 – – 165 – – 38 – – 166 – – 39 – – 167 – – 40 CL1-L CL1-L 168 CL2-L CL2-L 41 CL3-L CL3-L [1-L 2nd] 169
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 65 CLB-A CLB-A [9-A 2nd] 193 CLC-A CLC-A [A-A 2nd] 66 – – 194 – – 67 – – 195 – – 68 – – 196 – – 69 – – 197 – – 70 – – 198 – – 71 – – 199 – – 72 CL9-C CL9-C 200 CLA-C CLA-C 73 CLB-C CLB-C [9-C 2nd] 201 CLC-C CLC-C [A-C 2nd] 74 – – 202 – – 75 – – 203 – – 76 – – 204 – – 77 – – 20
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 101 – – 229 – – 102 – – 230 – – 103 – – 231 – – 104 CL9-L CL9-L 232 CLA-L CLA-L 105 CLB-L CLB-L [9-L 2nd] 233 CLC-L CLC-L [A-L 2nd] 106 – – 234 – – 107 – – 235 – – 108 – – 236 – – 109 – – 237 – – 110 – – 238 – – 111 – – 239 – – 112 CL9-N CL9-N 240 CLA-N CLA-N 113 CLB-N CLB-N [9
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 5 – – 133 – – 6 – – 134 – – 7 – – 135 – – 8 CL1-C CL1-C 136 CL2-C CL2-C 9 CL3-C CL3-C [1-C 2nd] 137 CL4-C CL4-C [2-C 2nd] 10 CL5-C CL5-C 138 CL6-C CL6-C 11 CL7-C CL7-C [5-C 2nd] 139 CL8-C CL8-C [6-C 2nd] 12 – – 140 – – 13 – – 141 – – 14 – – 142 – – 15 – – 143 – – 16 CL1-E CL1-E 144
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 41 CL3-L CL3-L [1-L 2nd] 169 CL4-L CL4-L [2-L 2nd] 42 CL5-L CL5-L 170 CL6-L CL6-L 43 CL7-L CL7-L [5-L 2nd] 171 CL8-L CL8-L [6-L 2nd] 44 – – 172 – – 45 – – 173 – – 46 – – 174 – – 47 – – 175 – – 48 CL1-N CL1-N 176 CL2-N CL2-N 49 CL3-N CL3-N [1-N 2nd] 177 CL4-N CL4-N [2-N 2nd] 50 CL5-N CL5-N 178
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 77 – – 205 – – 78 – – 206 – – 79 – – 207 – – 80 CL9-E CL9-E 208 CLA-E CLA-E 81 CLB-E CLB-E [9-E 2nd] 209 CLC-E CLC-E [A-E 2nd] 82 CLD-E CLD-E 210 CLE-E CLE-E 83 CLF-E CLF-E [D-E 2nd] 211 CLG-E CLG-E [E-E 2nd] 84 – – 212 – – 85 – – 213 – – 86 – – 214 – – 87 – – 215 – – 88 CL9-G CL9-G
Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 Port serial number Standard mode1 High Speed or Initiator/External MIX mode1 113 CLB-N CLB-N [9-N 2nd] 241 CLC-N CLC-N [A-N 2nd] 114 CLD-N CLD-N 242 CLE-N CLE-N 115 CLF-N CLF-N [D-N 2nd] 243 CLG-N CLG-N [E-N 2nd] 116 – – 244 – – 117 – – 245 – – 118 – – 246 – – 119 – – 247 – – 120 CL9-Q CL9-Q 248 CLA-Q CLA-Q 121 CLB-Q CLB-Q [9-Q 2nd] 249 CLC-Q CLC-Q [A-Q 2nd] 122 CLD-Q CL
Port serial number Standard mode High Speed or Initiator/External MIX mode Port serial number Standard mode High Speed or Initiator/External MIX mode 17 CL3-E CL3-E [1-E 2nd] 145 CL4-E CL4-E [2-E 2nd] 18 CL5-E CL5-E 146 CL6-E CL6-E 19 CL7-E CL7-E [5-E 2nd] 147 CL8-E CL8-E [6-E 2nd] 20 CL1-F CL1-F 148 CL2-F CL2-F 21 CL3-F CL3-F [1-F 2nd] 149 CL4-F CL4-F [2-F 2nd] 22 CL5-F CL5-F 150 CL6-F CL6-F 23 CL7-F CL7-F [5-F 2nd] 151 CL8-F CL8-F [6-F 2nd] 24 CL1-G CL1-G
Port serial number Standard mode High Speed or Initiator/External MIX mode Port serial number Standard mode High Speed or Initiator/External MIX mode 53 CL3-P CL3-P [1-P 2nd] 181 CL4-P CL4-P [2-P 2nd] 54 CL5-P CL5-P 182 CL6-P CL6-P 55 CL7-P CL7-P [5-P 2nd] 183 CL8-P CL8-P [6-P 2nd] 56 CL1-Q CL1-Q 184 CL2-Q CL2-Q 57 CL3-Q CL3-Q [1-Q 2nd] 185 CL4-Q CL4-Q [2-Q 2nd] 58 CL5-Q CL5-Q 186 CL6-Q CL6-Q 59 CL7-Q CL7-Q [5-Q 2nd] 187 CL8-Q CL8-Q [6-Q 2nd] 60 CL1-R CL1-R
Port serial number Standard mode High Speed or Initiator/External MIX mode Port serial number Standard mode High Speed or Initiator/External MIX mode 89 CLB-G CLB-G [9-G 2nd] 217 CLC-G CLC-G [A-G 2nd] 90 CLD-G CLD-G 218 CLE-G CLE-G 91 CLF-G CLF-G [D-G 2nd] 219 CLG-G CLG-G [E-G 2nd] 92 CL9-H CL9-H 220 CLA-H CLA-H 93 CLB-H CLB-H [9-H 2nd] 221 CLC-H CLC-H [A-H 2nd] 94 CLD-H CLD-H 222 CLE-H CLE-H 95 CLF-H CLF-H [D-H 2nd] 223 CLG-H CLG-H [E-H 2nd] 96 CL9-J CL9-J
Port serial number Standard mode High Speed or Initiator/External MIX mode Port serial number Standard mode High Speed or Initiator/External MIX mode 125 CLB-R CLB-R [9-R 2nd] 253 CLC-R CLC-R [A-R 2nd] 126 CLD-R CLD-R 254 CLE-R CLE-R 127 CLF-R CLF-R [D-R 2nd] 255 CLG-R CLG-R [E-R 2nd] 42 Overview of LUN Manager
Table 6 Port serial numbers and names (XP10000/SVS200) Port serial number Standard mode High Speed or Initiator/External MIX mode Port serial number Standard mode High Speed or Initiator/External MIX mode 64 CL1-A CL1-A 192 CL2-A CL2-A 65 CL3-A CL3-A[1-A 2nd] 193 CL4-A CL4-A[2-A 2nd] 66 CL5-A CL5-A 194 CL6-A CL6-A 67 CL7-A CL7-A[5-A 2nd] 195 CL8-A CL8-A[6-A 2nd] 68 CL1-B CL1-B 196 CL2-B CL2-B 69 CL3-B CL3-B[1-B 2nd] 197 CL4-B CL4-B[2-B 2nd] 70 CL5-B CL5-B 198 CL
iSCSI port and iSNS server settings You must make settings on iSCSI ports (and iSNS servers, if necessary) when configuring iSCSI environments. Use LUN Manager to specify the following items when configuring iSCSI environments. For instructions, see Defining LU paths and Making settings on iSCSI ports and iSNS servers. • IP address: You must specify the iSCSI port's IP address when configuring iSCSI environments. In LUN Manager, the initial value of the iSCSI port's IP address is 192.168.0.
• Whether to register iSCSI ports in iSNS servers: The iSNS server is a server computer on which an iSNS service is installed. iSNS is an acronym for Internet Storage Name Service. This server manages IP addresses and iSCSI names of iSCSI ports. Using iSNS servers is optional. If you configure and use iSNS servers, iSCSI ports are easily discovered and managed. NOTE: For more information about configuring iSNS servers, see the iSNS-related documentation.
requires authentication of the host, authentication is performed for the host. When the host is successfully authenticated, processing goes to the next phase. After authentication of the host succeeds, if the host requires user authentication for the host group that is connection target, the authentication of host groups phase starts. In this way, host groups and hosts authenticate with each other, that is, mutual authentication. In the authentication of host groups phase.
Figure 9 Authentication of hosts (Fibre Channel environments) Case A to Case D in Figure 9 is explained as follows: • Case A through Case C: When performing authentication of host groups • Case A: If the host's user information is registered on the host group, and authentication of the host is enabled The host group authenticates the user information sent from the host.
The host connects to the array without authentication of the host regardless of whether or not the host is configured for authentication by host groups with CHAP. In this case, although you do not need to register the host's user information on the host group, you can register the user information. NOTE: You should register the user information for all hosts to be connected to a host group that performs authentication of hosts.
Host B's user information is also registered on host group 1, but the authentication setting is disabled. Therefore, Host B can connect to the array without authentication. Host C's user information is not registered on host group 1. Therefore, when Host C tries to connect to the array, authentication fails and the connection request is denied regardless of Host C's setting. Host D is attached to host group 2, which does not perform authentication of hosts.
• When the Fibre Channel switch is not configured for mutual authentication, the Fibre Channel switch connects to the array. If the port's Fibre Channel switch is not configured for authentication with CHAP, the authentication fails and the Fibre Channel switch cannot connect to the array. • Case B: If the Fibre Channel switch's user information is registered on the port, but authentication of the Fibre Channel switch is disabled Each port does not perform authentication of the Fibre Channel switch.
• Settings for authentication of hosts • On the array: Use LUN Manager to specify whether authentication of hosts is performed on each iSCSI target. On an iSCSI target that performs authentication, register user information (iSCSI name, user name, and secret) of hosts allowed to connect to the iSCSI target. A secret is a password used in CHAP authentication. When registering user information, you can also enable or disable authentication on a host basis.
Figure 12 Authentication of hosts (iSCSI environments) Case A to Case D in Figure 12 are explained as follows: • Case A through Case C: When connecting via an iSCSI target that performs authentication of hosts • Case A: If the host's user information is registered on the iSCSI target, and authentication of the host is enabled The iSCSI target authenticates the user information sent from the host.
Regardless of the setting on the host, the iSCSI target performs authentication of the host, but results in a failure. The host cannot connect to the array. • Case D: When connecting via an iSCSI target that does not perform authentication of hosts The host connects to the array without authentication of the host regardless of whether or not the host is configured for authentication by iSCSI targets with CHAP.
Figure 13 Example of authentication of hosts (iSCSI environments) In Figure 13, iSCSI target 1 performs authentication of hosts, but iSCSI target 2 does not. Host A's user information is registered on iSCSI target 1, and the authentication setting is enabled. Therefore, if authentication of the host succeeds, Host A can connect to the array (or processing goes to the authentication of the iSCSI target).
For more information about configuring hosts, see the documentation for the operating system and iSCSI driver in your environment. Authentication of iSCSI targets (performing mutual authentication) When authentication of a host succeeds, the host performs authentication of the iSCSI target in reverse if the host requires (mutual authentication).
Overview of LUN Manager
2 Preparing to use LUN Manager System requirements To use LUN Manager, you need: • XP12000/XP10000/SVS200 array • LUN Manager optional program • WWW client computer connected to the array via a LAN To use LUN Manager, you must use the WWW client computer to log on to the SVP. When you are logged on, Command View XP or XP Remote Web Console, which is a Java® applet, is downloaded to the WWW client computer. You can perform LUN Manager operations in Command View XP or XP Remote Web Console.
Preparing to use LUN Manager
3 LUN Manager panes When you start LUN Manager, the Command View XP or XP Remote Web Console main pane displays the LUN Manager, Port, and Authentication panes. This chapter describes these panes. LUN Manager pane When you click the icon in the Command View XP or XP Remote Web Console main pane, LUN Manager starts and the LUN Manager pane appears. Use the LUN Manager pane to define LU paths and apply LUN security to logical volumes.
Figure 15 LUN Manager pane (icon under iSCSI folder selected) LU Path tree Use this tree to find information about LU paths. When you select a host group from this tree, the table on the right displays information about LU paths associated with the selected host group. The Subsystem folder is located at the top of the tree. The Fibre, NAS, and iSCSI folders appear below the Subsystem folder. Fibre folder If you double-click the Fibre folder, Fibre Channel ports in the array appear as icons.
Figure 16 Fibre folder Table 7 Fibre Channel port icons Icon Status Port in Standard mode. LUN security is disabled on the port. Port in Standard mode. LUN security is enabled on the port. Port in High Speed mode. LUN security is disabled on the port. Port in High Speed mode. LUN security is enabled on the port Port in Initiator/External MIX mode. LUN security is disabled on the port. Port in Initiator/External MIX mode. LUN security is enabled on the port.
Figure 17 NAS folder Table 8 NAS port icons Icon Status You can assign paths from this NAS port to logical volumes. You cannot assign paths from this NAS port to logical volumes because of a hardware failure or another reasons. When you double-click a NAS port, the following host groups appear: • NAS-Sys: When selected, information about paths to system LUs appears in the list on the right. The list contents are grayed out and cannot be changed. The group number (G-ID) of this host group is 00.
Figure 18 iSCSI folder Table 9 iSCSI port icons Icon Status LUN security is not applied to the port. LUN security is applied to the port When you double-click an iSCSI port in the tree, a list of iSCSI targets ( ) appears. The iSCSI target's group number (G-ID), name, and host mode appear on the right of this icon. For more information about host modes, see Table 16.
Table 10 LUN status icons Icon Status Logical volume to which an LU path is defined Expanded LU Command device Command device security Remote command device LUN to which no LU path is defined • CU:LDEV: CU image numbers appear on the left of the colon. LDEV numbers appear on the right of the colon. The combination of a CU image number and an LDEV number is used to identify a logical volume. If an LDEV number ends with #, the logical volume is an external LU.
Figure 19 WWN name table • Port: List of ports. The port's fibre address appears on the right of the port name. • Host Group: Host groups that are used to classify server hosts connected to the array. You must create host groups in the LUN Manager pane. • Name: Host bus adapter's nickname. You can specify nicknames in the LUN Manager pane. • WWN: Host bus adapter's World Wide Name. iSCSI name table Lists host bus adapters connected to the iSCSI ports on the array.
Table 11 LDEV status icons Icon Status Normal logical volume Expanded LU (that is, a LUSE volume) Volume the Customized Volume feature is applied to (that is, a CVS volume) Command device Command device security Remote command device If an LDEV number ends with #, the logical volume is an external LU. If an LDEV number ends with V, the logical volume is a virtual volume. • Emulation: Logical volume's emulation type. For CV volumes, CVS appears on the right of the emulation type.
NOTE: If you select an item related to Fibre Channel or NAS ports, you cannot use the Add iSCSI name button. • Add LU Path: Defines LU paths to logical volumes. Before using this button, you must select LUNs in the LU Path tree and select logical volumes in the LDEV table. • Apply: Applies settings in the pane to the array. • Cancel: Cancels settings in the pane. Port pane When you click the icon in the Command View XP or XP Remote Web Console main pane, LUN Manager starts.
Figure 22 Port pane (icon under iSCSI folder selected) Figure 23 Port pane (icon under NAS folder selected) Package tree Use this tree to select the port to be operated on. The Fibre, NAS, and iSCSI folders appear under the Subsystem folder at the top of the tree. Fibre folder When you double-click the Fibre folder, the folder opens and lists Fibre Channel channel adapters (CHAs). When you double-click a channel adapter, port blocks appear below the channel adapter. The following icons are used.
Table 12 Channel adapter and port block icons (Fibre folder) Icon Status Channel adapter package. All ports in this channel adapter package are in Standard mode. Channel adapter package. All or some ports in this channel adapter package are in High Speed mode. Channel adapter package. All or some ports in this channel adapter package are in Initiator/External MIX mode. Port block in a channel adapter package. Ports in this port block are in Standard mode. Port block in a channel adapter package.
• Type: Port‘s type. Fibre indicates a Fibre Channel port, which is used for connecting open-system hosts. • Host Speed: Fibre Channel port's data transfer speed. The unit is Gbps (gigabits per second). • Addr (Loop ID): Port‘s address. • Fabric: Indicates if a fabric switch is used. • Connection: Topology. The default is FC-AL. However, you must be aware that some fabric switches require you to specify the point-to-point topology.
iSCSI Function box Use this box to perform iSCSI-related operations. Figure 26 iSCSI Function box • Ping: Issues a ping command from an iSCSI port to a host. • Register: Registers information about iSCSI ports in the iSNS server. • Delete: Removes information about iSCSI ports from the iSNS server. Change Port Mode box This box appears when you select an icon under the Fibre folder in the Package tree. Use this box to change information in the Port table.
NOTE: If you are using a 2 Gbps HBA and switch, set the CHF port's transfer speed to 2 Gbps. If you are using a 1 Gbps HBA and switch, set the CHF port's transfer speed to 1 Gbps. If the Auto Negotiation setting is required, the linkup might be incorrect at server reboot. Check the channel lamp. If it is blinking, remove and re-insert the cable to perform the signal synchronization and linkup. • Fibre Addr.: The text box on the left displays the selected port's address.
• Set: Applies settings in the Change Port Mode box to the Port table. CHN list This list appears if you select an icon under the NAS folder in the Package tree. CHN is the channel adapter for NAS. The CHN list displays all NAS channel adapters. When you select a channel adapter in the Package tree, the CHN list displays information of the selected channel adapter. Information displayed in the CHN list is shown in Figure 29. Figure 29 CHN list (NAS channel adapters) • CHN Name: NAS channel adapter's name.
Authentication pane When you click the icon in the Command View XP or XP Remote Web Console main pane, LUN Manager starts. The LUN Manager pane includes the Authentication pane, which you can use to make settings for user authentication. User authentication can be performed in Fibre Channel and iSCSI environments. NOTE: The storage partition administrators can display information or perform the operation within only the allocated SLPR.
Figure 31 Authentication pane (port icon under Fibre folder selected) Figure 32 Authentication pane (icon under iSCSI folder selected) Port tree Use this tree to find information about user authentication on each port. When you select a port from this tree, the Authentication information (Target) list on the right displays user information for hosts registered on the port. In addition, the Authentication information (Host) list displays the selected port's user information.
Fibre folder If you double-click the Fibre folder, Fibre Channel ports in the array appear as icons. If you double-click a Fibre Channel port, host groups appear as icons. The host group name appears on the right of each icon. When the icon appears, the host group performs authentication of hosts. When the appears, the host group does not perform authentication of hosts. By default, the for all host group icons.
Figure 34 iSCSI folder Table 15 iSCSI port and iSCSI target status icons Icon Status iSCSI port. CLX-Y iSCSI name iSCSI name iSCSI target performs authentication of hosts. iSCSI target does not perform authentication of hosts. Port Information list • Port Name: Fibre Channel port name. For more information, see Table 3, Table 4, Table 5, and Table 6. • Time out: Period of time between authentication sessions to the same port.
• Authentication: Specifies if authentication for the host is performed. If the host is a target of user authentication, Enable appears. If the host is not a target of user authentication, Disable appears. iSCSI folder Displays user information for iSCSI targets allowed to connect to the port or iSCSI target selected in the tree. • Target Name: iSCSI target's iSCSI name. • User Name: iSCSI target's user name. When a user name is not defined for an iSCSI target, this column is blank.
4 LUN Manager operations This chapter describes how to start LUN Manager and various LUN Manager operations, such as defining LU paths. Starting LUN Manager 1. Start the Web browser. 2. Enter the following URL in the Web browser, and press Enter. The Storage Device List appears. http://IP-address-of-main-SVP (Web server)/cgi-bin/utility/sjc0000.cgi NOTE: If you are unsure of the IP address of the main SVP (Web server), ask the system administrator. 3. In the Storage Device List, click the SVP to log onto.
Creating host groups NOTE: If you are configuring a NAS environment, you do not need to follow the procedures described in this section. For instructions on defining LU paths in NAS environments, see Associating host groups or iSCSI targets to logical volumes. Creating host groups (when configuring Fibre Channel environments) You can connect multiple server hosts of different platforms to one port on the array. When configuring the system, you must group server hosts connected to the array by host groups.
CAUTION: Do not select Reserve from the list. Reserve indicates that the host mode is not currently supported. 5. If necessary, click Option, and select the host mode options. For more information about host mode options, see Table 17. Figure 36 Add New Host Group pane (Option selected) 6. Click OK. If a message appears, click OK. The host group name and host mode appear in blue. 7. Click Apply. A confirmation message appears. 8. Click OK. Settings are applied to the array.
Table 16 Host modes for host groups Host mode1 When to select this mode 00 Standard When registering Red Hat Linux or IRIX server hosts in the host group 03 HP When registering HP-UX server hosts in the host group 04 Sequent When registering DYNIX/ptx server hosts in the host group 05 OpenVMS When registering OpenVMS server hosts in the host group 07 Tru64 When registering Tru64® server hosts in the host group 09 Solaris When registering Solaris® server hosts in the host group 0A NetWare When
NOTE: If you register Windows server hosts in a host group, you need to ensure that the host mode of the host group is 0C: Windows, 2C: Windows Extension or 6C: Windows Extension 2. If you are thinking about creating LUSE volumes (i.e., expanded LUs), you should consider setting the host mode 2C: Windows Extension or 6C: Windows Extension 2 to the host group. If the host mode of a host group is 2C: Windows Extension or 6C: Windows Extension 2 and an LU path is defined, you can create an LUSE volume (i.e.
Table 17 Host mode options No. Host mode option When to select this option 2 VERITAS Database Edition/Advanced Cluster When VERITAS Database Edition/Advanced Cluster for Real Application Clusters or VERITAS Cluster Server 4.
The following procedure describes how to create iSCSI targets. The procedure for registering hosts to an iSCSI target is described in Registering hosts in host groups. 1. Start LUN Manager. The LUN Manager pane (Figure 15) appears. 2. Right-click the port for which you want to create an iSCSI target, and select Add New iSCSI Target. The Add New iSCSI Target pane appears. Figure 37 Add New iSCSI Target pane 3. In the Target name box, enter the iSCSI target name.
Figure 38 Add New iSCSI Target pane (Option selected) NOTE: After you click Option, the pane expands to display a list of host mode options. The No. column indicates option numbers. Select the check box for the option you want to specify. 7. Click OK. If a message appears, click OK. The iSCSI target name and host mode appear in blue. 8. Click Apply. A confirmation message appears. 9. Click OK. Settings are applied to the array.
NOTE: • A nickname can consist of up to 32 ASCII characters (letters, numerals, and symbols). However, you cannot use the following characters for nicknames: \ / : , ; * ? " < > | • You cannot use spaces for the first or last character in nicknames. • Nicknames are case-sensitive. For example, hp and HP are different nicknames. 1. Start LUN Manager. The LUN Manager pane (Figure 14) appears. 2.
NOTE: You cannot add WWNs to host groups for initiator ports. Figure 40 Add New WWN dialog box (registering a host that has never been connected to the array) b. In the WWN list, select the host bus adapter. If the list does not include the host bus adapter, enter the WWN in the WWN box. c. If necessary, enter a nickname for the host bus adapter. d. Click OK. If a message appears, click OK. The specified WWN and nickname appear below the selected host group. 4. Click Apply.
a. In the iSCSI name table, select the port to which the host is connected from the Port list. b. In the iSCSI name list, select the host bus adapter. From the tree, select an iSCSI target, and click Add iSCSI name. Figure 41 Add New iSCSI name pane (registering a host that was previously connected to the array) • In this list, only iSCSI names of hosts that issued login commands to ports appear.
Figure 42 Add New iSCSI name pane (registering a host that has never been connected to the array) b. In the iSCSI name list, select the host bus adapter. If the list does not include the host bus adapter, enter the iSCSI name in the iSCSI name box. c. If necessary, enter a nickname for the host bus adapter. d. Click OK. The specified iSCSI name and nickname appear below the selected iSCSI target. 4. Click Apply. A confirmation message appears. 5. Click OK.
Figure 43 Information about LU paths to be defined (Fibre Channel environment) Figure 44 Information about LU paths to be defined (iSCSI environment) 5. Click OK. Settings are shown in the LU Path table, but not applied to the array yet. 6. Click Apply. A confirmation message appears. 7. Click OK. Settings are applied to the array, and LU paths are defined. Changing or viewing LU path settings Deleting LU paths CAUTION: • Do not remove LU paths when host I/O is in progress.
3. In the tree, select a host group or iSCSI target. The LU Path table displays information about LU paths associated with the selected host group or iSCSI target. 4. In the LU Path table, select one or more LUNs to which volumes are assigned. (If a volume is assigned to a LUN, columns on the right of the LUN column are not empty.) 5. Right-click the selection, and select Release LU Path. A confirmation message appears.
Changing a host group's name and host mode NOTE: • You cannot perform this operation on host groups for initiator ports. • You cannot perform this operation on host groups for NAS ports. CAUTION: Before changing a host group's host mode, HP recommends that you first back up data on the port the host group belongs to. The operation for changing the host mode should not be destructive, but data integrity cannot be guaranteed without a backup. 1. Start LUN Manager. The LUN Manager pane (Figure 14) appears. 2.
Figure 48 Change Host Group dialog box (Option selected) NOTE: After you click Option, the pane expands to display a list of host mode options. The No. column indicates option numbers. Select the check box for the option you want to specify. 5. Click OK. Changes are indicated in blue in the table. 6. Click Apply. A confirmation message appears. 7. Click OK. Changes to the host group name and host mode are applied to the array.
Figure 49 Change iSCSI Target pane 3. To change the iSCSI target's name, enter a new name in the Target name box. To change the alias, enter a new alias in the Target alias box. iSCSI target aliases can include letters, numbers, periods (.), hyphens (-), and colons (:); but cannot include double-byte characters. iSCSI target aliases are case-sensitive. An iSCSI target alias can consist of up to 32 characters To change the host mode (see Table 16), select the new host mode from the Host Mode list. 4.
1. Start LUN Manager. The LUN Manager pane (Figure 14) appears. 2. In the tree, right-click the desired group, and select Delete Host Group. A confirmation message appears. 3. Do either of the following: • To delete all WWNs and the host group, click Yes. • To delete the host group but not the WWNs in the host group, click No. 4. Click Apply. A confirmation message appears. 5. Click OK. Settings are applied to the array. Deleting iSCSI targets NOTE: You cannot delete iSCSI target 0 (zero).
Initializing iSCSI target 0 (zero) If you follow the procedure below, iSCSI target 0 (zero) is set to its initial state. This procedure removes all LU paths related to iSCSI target 0. This procedure also changes iSCSI target 0's host mode to Standard and initializes the iSCSI target name. After this procedure, the iSCSI target's name changes to its default name. 1. Start LUN Manager. The LUN Manager pane (Figure 15) appears. 2.
NOTE: The change in the pane does not affect any port that satisfies one of the following conditions: • The resulting nickname is already used as the nickname of a host bus adapter connected to the port. • The resulting WWN exists in the port. 7. Click OK. If a confirmation message appears, click OK. Changes appear in blue in the tree. NOTE: If you select Apply this change to other ports, too, and click OK, the Check WWNs dialog box appears and lists the host bus adapters to be changed.
Figure 53 Change iSCSI name & Nickname pane 4. To change the iSCSI name, enter a new iSCSI name or select another iSCSI name in the iSCSI name list. To change the nickname, enter a new nickname in the Nickname box. 5. If necessary, select Apply this change to other ports, too. If this check box is selected, the change in the pane also affects other ports. For example, suppose the same host bus adapter (that is, the same iSCSI name) is located below ports CL1-A and CL2-A in the tree.
Figure 54 Check iSCSI names dialog box 7. Click Apply. A confirmation message appears. 8. Click OK. Changes are applied to the array. Deleting host bus adapters from host groups NOTE: You cannot perform this operation on host groups for NAS ports. 1. Start LUN Manager. The LUN Manager pane (Figure 14) appears. 2. In the tree, right-click a host bus adapter ( appears. ), and select Delete WWN. A confirmation message 3. Click Yes. 4. Click Apply. A confirmation message appears. 5. Click OK.
Deleting unneeded WWNs from the WWN name table If you disconnect a host that was connected via a cable to the array, the host's WWN remains in the WWN name table on the LUN Manager pane. 1. Start LUN Manager. The LUN Manager pane (Figure 14) appears. 2. In the WWN name table, locate WWNs that are not registered in any host group. (If the Host Group column is blank, the WWN is not registered in any host group.) From these WWNs, right-click the WWN you want to delete, and select Erase WWN. 3. Click Apply.
Figure 55 Concatenation List pane • If the Concatenation List command does not appear, the logical volume is not dispersed across parity groups. Defining and viewing alternate paths Use LUN Manager to define alternate paths. If an LU path fails, you can switch to its alternate path. To create an alternate path, you must copy the original path from one port to another.
b. Right-click the copy destination port, and select Paste. If a confirmation message appears, click OK. NOTE: You cannot paste paths to initiator port. 4. To copy one or more (but not all) LU paths defined to a host group or iSCSI target, complete the following steps: a. In the tree, select the host group or iSCSI target. b. In the LU Path table, select one or more LUNs to which volumes are assigned. (If a volume is assigned to a LUN, columns on the right of the LUN column are not empty.) c.
1. Start LUN Manager, and display the LUN Manager pane (Figure 14 or Figure 15). 2. To specify the LU paths you want to copy: a. In the tree, double-click a Fibre Channel or iSCSI port (copy source port), and select a host group or iSCSI target. The LU Path list displays information about LU paths. b. In the list, select one or more LUNs to which volumes are assigned. If a volume is assigned to a LUN, columns on the right of the LUN column are not empty. c. Right-click the selection, and select Copy Paths.
NOTE: If nothing appears in the table cells to the right of a LUN, no path is defined to the LU. Therefore, no alternative path is defined to the LU. • In the LDEV table, right-click a logical volume (that is, an LDEV), and select Alternate Paths. NOTE: If nothing appears in the Paths column for a row in the LDEV list, no alternate paths are defined to the LDEV corresponding to that table row. When you finish the operation, the Alternate Paths pane appears and displays a list of alternate paths.
NOTE: • You cannot apply LUN security to NAS ports. • If a port has the External attribute, you cannot apply LUN security to the port. Enabling LUN security NOTE: • You cannot apply LUN security to NAS ports. • If a port has the External attribute, you cannot apply LUN security to the port. 1. Start LUN Manager. The LUN Manager pane (Figure 14 or Figure 15) appears. 2. In the tree, locate the port. 3. See the text on the right of the port name to find the LUN security status.
Configuring arrays for using RAID Manager XP commands The system administrator can enter RAID Manager XP commands from open-system hosts to perform Continuous Access XP and Business Copy XP operations on logical devices. For example, use RAID Manager XP commands to create and split pairs. To enable the system administrator to enter RAID Manager XP commands from open-system hosts, you must specify at least one logical device as the command device.
NOTE: • If nothing appears in the LU Path table, select a host group ( ) in the tree. • The icon indicates a logical volume to which command device security is already applied. icon does not indicate any logical device. • The 3. Select Cmd. Dev. Security: Disable -> Enable. A confirmation message appears. 4. Click OK. 5. Click Apply. A confirmation message appears. 6. Click OK. Settings are applied to the array.
NOTE: You cannot configure Fibre Channel ports and perform operations related to NAS channel adapters at the same time. Therefore, when you perform operations on a NAS channel adapter first in the Port pane, you cannot configure Fibre Channel ports. Click Apply once to apply changes to the array, and then configure the Fibre Channel port. Specifying Fibre Channel topologies The term topology refers to how devices are connected to each other. For more information, see Fibre Channel topologies. 1.
5. Click Set. A confirmation message appears. 6. Click OK. Settings are applied to the Port table, but not to the array. Changes are indicated in blue. 7. Click Apply. A confirmation message appears. 8. Click OK. Settings are applied to the array. Specifying a Fibre Channel port's data transfer speed You can adjust the data transfer speed for Fibre Channel ports to optimize system performance. For more information, see Data transfer speed for Fibre Channel ports. 1.
A confirmation message appears. 5. Click OK. 6. Click Apply. A confirmation message appears. 7. Click OK. Settings are applied to the array. NOTE: Storage partition administrators cannot apply High Speed or Initiator/External MIX mode. Making settings on iSCSI ports and iSNS servers Use the Port pane (Figure 22) to configure iSCSI ports in the array. You can also use this pane to make settings on iSNS servers and modify settings when the system is operating. Making settings on iSCSI ports 1.
Figure 57 Register Ports to iSNS Server pane Figure 58 Delete Ports from iSNS Server pane 3. From the iSCSI Ports list, select an iSCSI port. iSCSI port information appears in the Ports to be Registered or Ports to iSNS Deleted list. Use Add or Delete to move information between the lower and upper lists. 4. Click OK. The Result of Registration to iSNS Server or Result of Deletion from iSNS Server pane appears.
Figure 59 Result of Registration to iSNS Server pane Figure 60 Result of Deletion from iSNS Server pane Checking the status of the connection between hosts and the array (iSCSI environments only) In iSCSI environments, use LUN Manager to issue a ping command from an array port to a host. The ping command checks whether the host and array can communicate with each other. If the host responds to the ping command, the host and array can communicate with each other. 1.
Figure 61 Ping pane 3. From the From (Subsystem Port) list, select an iSCSI port. 4. In To (IP Address) box, enter the host's IP address. 5. Click OK. A ping command is issued from the iSCSI port to the host five times. After the ping command is issued five times, the Ping Status pane appears and displays the results of the first to fifth attempts at issuing the ping command. The results appear in the order attempts were made. Figure 62 Ping Status pane 6.
Setting user authentication (Fibre Channel environments) When configuring Fibre Channel environments, use the Authentication pane (Figure 30 and Figure 31) to set user authentication on host groups, Fibre Channel ports, and Fibre Channel switches of the array. For an overview of user authentication, see User authentication (Fibre Channel environments). NOTE: The hosts to be connected must also be configured for authentication by host groups (and for authentication of host groups by the host, if required).
3. Right-click any point in the Authentication Information (Host) list, and select Add New User Information. The Add New User Information (Host) pane appears. Figure 63 Add New User Information (Host) pane Specify the following user information for the host you want to allow to connect: • Group Name: Host bus adapter's group name. Select one from the list. All group names of host bus adapters connected to the selected port by the cable appear in the list.
2. In the Port tree, expand the Fibre folder, and select a port or host group on which the user information you want to change is registered. All user information for hosts registered on the selected port or host group appears in the Authentication Information (Host) list. 3. In the User Information (Host) list, right-click the user information item you want to change, and select Change User Information. The Change User Information (Host) pane appears. Figure 64 Change User Information (Host) pane 4.
Figure 65 Delete Authentication Information pane 4. Click OK. 5. Click Apply. A confirmation message appears. 6. Click OK. Settings are applied to the array. Specifying a host group's user information (when performing mutual authentication) To perform mutual authentication, you must specify user information for host groups on array's ports. Specify unique user information for each host group. You can change the specified user information for host groups the same way you specified them initially. 1.
• User Name: Host group's user name, up to 16 characters. You can use specified alphanumeric characters. User names are case-sensitive. • Secret: Secret (that is, a password used in CHAP authentication) between 12 to 32 characters. You can use alphanumeric characters, spaces, and the following symbols in a secret: . - + @ _ = : / [ ] , ~ • Re-enter Secret: Specify the secret, again, for confirmation. 4. Click OK.
Table 18 Combinations of port settings and connection results (Fibre Channel environments) Port settings Host settings Connection results Authentication: at host group Host's user information Enable Registered Registered Connected if the authentication of the host succeeded Enable Registered Not registered Failed to be authenticated and cannot be connected Enable Not registered Registered Failed to be authenticated and cannot be connected Disable — 1 — 1 Connected without authenticatio
Specifying a Fibre Channel port's information To perform user authentication in Fibre Channel environments, you must specify information for the Fibre Channel ports of the array. 1. Start LUN Manager, and display the Authentication pane (Figure 30). 2. In the Port tree, double-click the Subsystem folder. If the array contains Fibre Channel adapters, the Fibre folder appears below the Subsystem folder. The port's information appears in the Port Information list. 3.
Figure 68 Default Setting(User Name/Secret) pane Specify the following user information: • User Name: Fiber Channel's user name, up to 16 characters. You can use alphanumeric characters in a user name. User names are case-sensitive. • Secret: Secret (that is, a password used in CHAP authentication) between 12 to 32 characters. You can use alphanumeric characters. • Re-enter Secret: Specify the secret, again, for confirmation. 5. Click OK. 6. Click Apply. A confirmation message appears. 7. Click OK.
• Secret: Secret (that is, a password used in CHAP authentication) between 12 to 32 characters. You can use alphanumeric characters. • Re-enter Secret: Specify the secret, again, for confirmation. 5. Click OK. 6. Click Apply. A confirmation message appears. 7. Click OK. Settings are applied to the array. Clearing a Fibre Channel switch's user information 1. Start LUN Manager, and display the Authentication pane (Figure 30). 2. In the Port tree, double-click the Subsystem folder.
6. Click OK. Settings are applied to the array. To return the Fibre Channel setting, perform the same operation, except select Authentication bi-directional->unidirectional in step 4. Specifying whether a Fibre Channel switch can perform authentication To enable Fibre Channel switches to authenticate hosts, you must enable the Fibre Channel switch's user authentication settings. By default, Fibre Channel switch authentication is disabled. To enable a Fibre Channel switch to authenticate hosts: 1.
If you double-click an iSCSI port, iSCSI target appears as an icon. The iSCSI name appears on the appears, the iSCSI target performs authentication of hosts. When right of each icon. When appears, the iSCSI target does not perform authentication of hosts. By default, for all iSCSI targets. 4. Right-click an iSCSI target displayed with target's icon changes to appears , and select Authentication Disable -> Enable. The iSCSI , and the port name appears in blue. 5. Click Apply.
Figure 71 Add New User Information (Host) pane NOTE: You should register user information for all hosts to be connected to an iSCSI target that performs authentication of hosts. To allow a specific host to connect to such an iSCSI target without authentication, configure the iSCSI target and the host as follows: • On the host: It does not matter whether or not you configure the host for authentication by ports with CHAP.
NOTE: You cannot change iSCSI names when you change user information. 1. Start LUN Manager, and display the Authentication pane (Figure 30). 2. In the Port tree, double-click the iSCSI folder, and select the port or iSCSI target on which the user information you want to change is registered. All user information for hosts registered on the selected port appears in the Authentication information (Host) list. 3.
Figure 73 Delete Authentication Information pane 4. Click OK. 5. Click Apply. A confirmation message appears. 6. Click OK. Settings are applied to the array. Specifying an iSCSI target's user information (when performing mutual authentication) To perform mutual authentication, you must specify user information for iSCSI targets on the array's ports. Specify unique user information for each iSCSI target.
Figure 74 Specify Authentication Information pane Specify the following user information for the port or iSCSI target selected in the Port tree: • Target Name: Selected port's iSCSI name. You cannot change the iSCSI name. • User Name: iSCSI target's user name up to 128 characters. You can use alphanumeric characters, spaces, and the following symbols in a user name: . - + @ _ = : / [ ] , ~ User names are case-sensitive. For example, port1 and Port1 represent different user names.
• Whether or not the user information for the host that attempts to connect is registered on the iSCSI target Table 20 shows the relationship between combinations of iSCSI target settings and connection results in authentication of hosts. Regardless of whether or not the host is configured for authentication by ports with CHAP, the connection results are as follows, unless otherwise noted.
When the reboot starts, BUSY (Shutdown) appears in the OS Status column. If the OS restarted, UP appears. NOTE: You can stop the OS by right-clicking the channel adapter in the Package list and selecting Reboot instead of using the Reboot button. Stopping a NAS channel adapter's OS 1. Start LUN Manager, and display the Port pane (Figure 23). 2. In the Package tree, select the NAS folder or a NAS channel adapter. • If you select the NAS folder, the CHN list displays the NAS channel adapters in the array.
NOTE: You can start the OS by right-clicking the channel adapter in the Package list and selecting Boot instead of using the Boot button.
5 Troubleshooting LUN Manager Troubleshooting For troubleshooting information on the array, see the array's documentation. You are responsible for the operation and normal maintenance of the Command View XP computer or XP Remote Web Console. The following are some guidelines for troubleshooting the Command View XP computer or XP Remote Web Console: • Check the cabling and LAN: Verify that both the computer and LAN cabling are firmly attached, and the LAN is operating properly.
Table 21 Troubleshooting LUN Manager Error Condition Recommended Action The program on the SVP is updated. Exit all Web browsers on the Command View XP computer, and restart the browsers. If in doubt, exit and restart the browsers. The Command View XP computer experiences an error. Save the Java log file on the Command View XP computer, and report to your HP account support representative. For Windows 2000, the Java log file is in the following place: c:\Documents and Settings\login user ID\plugin131.
6 Finding an open-system host's World Wide Name (WWN) If you are configuring a Fibre Channel environment, you must verify that the fibre adapters and Fibre Channel device drivers are installed on the open-system hosts. Next, you must find the World Wide Name (WWN) of the host bus adapter used in each open-system host. The WWN is a unique identifier for a host bus adapter in a open-system host, consisting of 16 hexadecimal digits. This chapter describes how to find a host's WWN.
Figure 75 LightPulse Utility/NT pane If you do not have a shortcut to the Utility, do the following: a. Go to the Start menu, select Find, and choose Files and Folders. The Find pane opens. b. In the Named field, enter lputilnt.exe. In the Look in box, choose the hard drive containing the Emulex mini-port driver. c. Click Find Now to search for the LightPulse Utility. NOTE: If you cannot find the LightPulse Utility, contact Emulex technical support. d. In the Find: Files named list box, select lputilnt.
# 4. Verify that the listed Fibre Channel adapters are correct, and record the listed WWNs. Finding WWNs in AIX, SGI Irix, or Sequent environments To find WWNs in AIX, SGI Irix, or Sequent environments, use the fibre switch connected to the host. The method for finding the WWN of the connected server on each port using the fibre switch depends on the type of switch. For instructions on finding the WWN, see the fibre switch's documentation. Finding WWNs in HP-UX environments 1.
NOTE: When an A5158 Fibre Channel adapter is used, enter the following for the device name at the command line prompt: /usr/sbin/ioscan -fnC fc 6. Record the Fibre Channel device file name (for example, /dev/td0). NOTE: When the A5158 Fibre Channel adapter is used, enter the following to list the WWN for the device with the device file name: /opt/fcms/bin/fcmsutil 7. Record the WWN and repeat the above steps for each Fibre Channel device you want to use.
7 Overview of Volume Manager and Custom Volume Size Volume Manager and Custom Volume Size (CVS) are functions for open systems and mainframe systems. To use these functions, you need the software called HP StorageWorks LUN Configuration and Security Manager XP. This chapter describes Volume Manager and CVS. Overview of Volume Manager This section describes the Volume Manager function and configuration of LUSE volumes (expanded LUs).
Figure 76 LUSE configuration Volume Manager guidelines The following are the specifications and restrictions on LDEVs used to configure a LUSE volume: • Open volumes (OPEN-3, OPEN-8, OPEN-9, OPEN-E, OPEN-L, and OPEN-V) are supported. • The number of LDEVs combined into a LUSE volume must be within the range of 2 to 36. NOTE: The number of expanded LUs (LDEVs) should not exceed 36, even if the LUSE volume contains another LUSE volume.
• The maximum capacity of a LUSE volume is 60 TB. NOTE: When a host accesses a LUSE volume, the host can only access less than 2 TB of the LUSE volume's address area. • • • • • Combining command devices and Just In Time volumes into a LUSE volume is not supported. The access attribute must be set to Read/Write. Combining internal LUs, external LUs, and virtual volumes (V-VOLs) is not supported. During online, the host mode must not be 0x0C [Windows].
CAUTION: Note the following points when you perform a Volume Manager operation using a path-defined LDEV: • If a path is defined from a Windows 2000, Windows Server 2003, or AIX 5.2 host to an LDEV, you can use the LDEV for Volume Manager operations using a path-defined LDEV. However, if a path is defined from a host running another operating system to an LDEV, you cannot use the LDEV for Volume Manager operations using a path-defined LDEV.
Figure 77 Overview of Volume Initialize function Figure 78 Overview of Make Volume function Parity group configuration One parity group consists of a maximum of 16 VDEVs. For RAID-5 (7D + 1P) or RAID-6 (6D + 2P) levels, a maximum of 512 fixed-size volumes (FVs) and a certain amount of free space are available in one VDEV. For other RAID levels, a maximum of 256 FVs and a certain amount of space are available in one VDEV.
Figure 79 Parity group configuration As the result of CVS operations, a VDEV contains FVs, CVs, and free spaces that are delimited in logical cylinders. Sequential free spaces are combined into a single free space (see Figure 80). Figure 80 Virtual CVS volume configuration Volume to Space function This function converts one or more LDEVs (FVs or CVs) into free space, which deletes the selected LDEVs from that VDEV.
• • • • • The The The The The LDEV LDEV LDEV LDEV LDEV must be read/write-enabled. or LUSE volume must not be a pool volume (pool-VOL). must not be a journal volume. must not be a remote command device. must not contain extents. Install CV function This function defines and installs one or more CVS volumes under an existing volume (free space in a VDEV).
Table 23 CVS specifications Parameter Mainframe systems Open systems Track format 3380, 3390 OPEN-3, OPEN-8, OPEN-9, OPEN-E OPEN-V Emulation type 3380-3, 3380-3A, 3380-3B, 3380-3C, 3380-F*, 3380-K*, 3380-KA*, 3380-KB*, 3380-KC* 3390-3, 3390-3A, 3390-3B, 3390-3C, 3390-3R, 3390-9, 3390-9A, 3390-9B, 3390-9C, 3390-L, 3390-LA, 3390-LB, 3390-LC, 3390-M, 3390-MA, 3390-MB, 3390-MC NF80-F*, NF80-K*, NF80-KA*, NF80-KB*, NF80-KC* OPEN-3, OPEN-8, OPEN-9, OPEN-E OPEN-V Ability to intermix emulation types Dep
Table 24 CV capacity by emulation type (mainframe systems) Emulation type Minimum CV capacity (Cyl) Maximum CV capacity (Cyl) Number of control cylinders (Cyl) 3380-3 1 3,339 7 3380-3A 1 3,339 7 3380-3B 1 3,339 7 3380-3C 1 3,339 7 3380-F 1 3,983 22 3380-K 1 2,655 7 3380-KA 1 2,655 7 3380-KB 1 2,655 7 3380-KC 1 2,655 7 3390-3 1 3,339 6 3390-3A 1 3,339 6 3390-3B 1 3,339 6 3390-3C 1 3,339 6 3390-3R 1 3,339 6 3390-9 1 10,017 25 3390-9A 1 10,017
Table 25 CV capacity by emulation type (open systems) Emulation type Minimum CV capacity (CYL) Maximum CV capacity (CYL) Number of control cylinders (Cyl) OPEN-V 48,000 KB 3,019,898,880 KB (2.
NOTE: • Round up the value enclosed by two up arrows (↑) to the nearest whole number. • The user-specified CV capacity is expressed in megabytes. To calculate the CV's entire capacity, use the following formula. The resulting entire capacity is expressed in megabytes: ↑ user-area-capacity ÷ boundary-value ↑ × boundary-value ÷ 1024 NOTE: • Round up the value enclosed by two up arrows (↑) to the nearest whole number. • The user area capacity is expressed in kilobytes.
NOTE: • Round up the value enclosed by two up arrows (↑) to the nearest whole number. • The user-specified CV capacity is expressed in blocks. • The boundary value is expressed in kilobytes. The boundary value depends on volume emulation types and RAID levels (see Table 28). If the emulation type is other than OPEN-V • If the CV capacity unit is MB (megabytes): To calculate the CV's user area capacity, use the following formula. The resulting user area capacity is expressed in kilobytes.
NOTE: • Round up the value enclosed by two up arrows (↑) to the nearest whole number. • The user-specified CV capacity is expressed in blocks. • The management area capacity is expressed in kilobytes. The management area capacity depends on volume emulation types (see Table 27). • The boundary value is expressed in kilobytes. The boundary value depends on volume emulation types and RAID levels (see Table 28).
Table 28 Boundary value for RAID levels Emulation type Boundary value for RAID1 (2D+2D) Boundary value for RAID5 (3D+1P) Boundary value for RAID5 (7D+1P) Boundary value for RAID6 (6D+2P) 3380-xx 768 1,152 2,688 2,304 3390-xx 928 1,392 3,248 2,784 OPEN-xx (except for OPEN-V) 768 1,152 2,688 2,304 OPEN-V 1,024 1,536 3,584 3,072 NOTE: • The xx is a variable indicating one or more numbers or letters. • Boundary values are expressed in kilobytes.
Table 30 Settings for the Make Volume operation (OPEN-V only) No. Setting CVS volumes to be created 1 Specify the capacity and number of variable-sized volumes (CVs) under a CVS volume. A CVS volume that has the specified number of CVs of the specified capacity is created. This is the same as the Install CV operation. 2 Specify the number of variable-sized volumes (CVs). A CVS volume that has the specified number of CVs is created (the VDEV is divided by the specified number).
Table 31 SSID requirements Controller emulation type SSID requirement CVS support 3990-6, 3990-6E (0104)x - (FFFD)x 3390-3, 3390-3A, 3390-3B, 3390-3C, 3390-9, 3390-9A, 3390-9B, 3390-9C, OPEN-3, OPEN-8, OPEN-9, OPEN-E, and OPEN-V volumes 2105-F20 (0104)x - (FFFD)x 3380-3, 3380-3A, 3380-3B, 3380-3C, 3390-3, 3390-3A, 3390-3B, 3390-3C, 3390-3R 3390-9, 3390-9A, 3390-9B, 3390-9C, 3390-L, 3390-LA, 3390-LB, 3390-LC, 3390-M, 3390-MA, 3390-MB, 3390-MC, OPEN-3, OPEN-8, OPEN-9, OPEN-E, and OPEN-V volumes Requi
8 Preparing to use Volume Manager or Custom Volume Size This chapter describes the environment you must prepare to operate Volume Manager or Custom Volume Size (CVS). System requirements To operate Volume Manager or CVS, you need the following: • XP12000/XP10000/SVS200 array • Command View XP computer or XP Remote Web Console • Licensed Volume Manager and/or CVS software NOTE: To use the Volume Manager or CVS function, you need the software called HP StorageWorks LUN Configuration and Security Manager XP.
guide for XP Disk Arrays or the HP StorageWorks XP Remote Web Console user guide for XP12000/XP10000/SVS200. 2. From the option buttons on the left of the Command View XP or XP Remote Web Console main pane ). The Volume for activating the array's features, click the Volume Manager button ( Manager main pane appears and enables you to operate Volume Manager or CVS. 3. The Volume Manager pane is the initial pane that appears. To operate CVS, click the Customized Volume tab.
Figure 81 Icons showing Unlocked status and View mode Figure 82 Mode changing confirmation message Figure 83 Icons showing Locked status and Modify mode HP StorageWorks LUN Configuration and Security Manager XP user guide for the XP12000/XP10000/SVS200 157
Preparing to use Volume Manager or Custom Volume Size
9 Volume Manager operations This chapter describes Volume Manager operations. Volume Manager panes This section describes components of the Volume Manager panes. Volume Manager main pane To open the Volume Manager pane, click the Volume Manager button ( ). Figure 84 Volume Manager pane The Volume Manager pane has the following features. LDEV Information tree This tree is on the upper-left of the Volume Manager pane.
Table 32 LDEV status icons Icon LDEV status Normal LDEV Variable-sized volume (CV) Expanded (LUSE) volume LDEV Information table This table is in the upper-right of the Volume Manager pane, and displays data for the LDEV you select in the LDEV Information tree. The LDEV Information table displays detailed information for all open-system LDEVs in the selected CU. If you select a normal LDEV, the information in this table is for the top LDEV.
• Paths: Number of paths set for the LDEV. If this column displays the number of paths for an LDEV, you can use the LDEV as the top LDEV of a LUSE volume (see Volume Manager operations using a path-defined LDEV). • Access Attribute: Access attribute set for the LDEV. • IO Suppression Mode: Displays Disable when I/O requests from hosts are suppressed, or Enable if I/O requests from hosts are not suppressed.
NOTE: The RAID level is left unspecified with a hyphen (-) when the LDEV is an external LU or virtual volume (V-VOL). • PG: Combination of the disk group and parity group. If the LDEV extends over two or more parity groups, the smaller parity group number appears. NOTE: If a parity group number starts with E (for example, E1-1), the parity group consists of one or more external LUs.
Displays the Set LUSE confirmation pane (Figure 86). You can confirm whether or not you want to continue the operation to create a LUSE volume. For more information, see Creating LUSE volumes. • Release LUSE Volume Displays the Release LUSE confirmation pane (Figure 87). You can confirm whether or not you want to continue the operation to release a LUSE volume. For more information, see Releasing LUSE volumes. • Reset LUSE Volume Displays the Reset LUSE confirmation pane (Figure 88).
• Emulation: LDEV's emulation type. • Capacity: LDEV's capacity. • OK: Creates the LUSE volume and sets the LUSE volume configuration to have LDEVs in the LUSE components list. LDEVs registered as components of the LUSE volume appear in blue bold italics in the LDEV Information table. • Cancel: Cancels the operation to create a LUSE volume using LDEVs in the list. Release LUSE Confirmation pane When you select Release LUSE Volume, the Release LUSE Confirmation pane appears.
• Cancel: Cancels the release Volume Manager operation. Reset LUSE Confirmation pane When you select Reset LUSE Volume from the Volume Manager operation shortcut menu, the following pane appears. You can confirm the LDEV that is still not registered to the array as a LUSE volume and whether or not you want to reset this unregistered LUSE volume to the state it was in before it was created.
Figure 89 Concatenation List pane NOTE: If a parity group number starts with E (for example, E1-1), the parity group consists of one or more external LUs. Volume Manager operations This section provides instructions for performing Volume Manager operations. Preparing to use Volume Manager Before starting a Volume Manager operation on a selected array, unmount the open system volumes, and remove the LU paths to the open volumes. For instructions, see Deleting LU paths.
NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU. For more information about external LUs, see the HP StorageWorks External Storage XP user guide. NOTE: If an LDEV number ends with V (for example, 00:01V), the LDEV is a virtual volume (V-VOL). For more information about V-VOLs, see the HP StorageWorks Snapshot XP user guide. Viewing concatenated parity groups 1. From the Volume Manager pane, select a CU number in the LDEV Information tree.
a. To add more LDEVs to the Expanded LDEVs list, select normal LDEVs, CVS volumes, or LUSE volumes in the Free LDEVs table, and click Add. b. To delete LDEVs from the Expanded LDEVs list, select the LDEVs in the Expanded LDEVs list, and click Delete. 4. Click Set. A pane appears.
b. To perform a Volume Manager operation that affects more than one SLPR or CLPR, click OK. A confirmation pane appears. Go to step 6. If you do not want to perform a Volume Manager operation that affects more than one SLPR or CLPR, click Cancel. The previous pane appears, and you can retry the operation. c. If the Set LUSE Confirmation pane appears, go to step 6. 6. Click OK (or Cancel). NOTE: New settings appear on the pane in blue bold italics are not yet registered to the array.
Releasing LUSE volumes CAUTION: Releasing LUSE volumes is a destructive operation. Move and/or back up data before proceeding. Delete all SCSI paths to the LUSE volume you want released. 1. In the Volume Manager pane, select the CU number from the LDEV Information tree. The LDEV Information table displays all LDEVs in the selected CU. 2. In the LDEV Information table, right-click a LUSE volume, and select Release LUSE Volume. The Release LUSE Confirmation pane appears. 3.
3. Click OK. The setting of the selected LUSE volume that is not registered yet is reset to the state it was in before this LUSE volume was created, and the LUSE volumes or LDEVs constituting the selected LUSE volume that has just been reset appear in the LDEV Information table.
Volume Manager operations
10 Custom Volume Size operations This chapter describes Custom Volume Size (CVS) operations. Custom Volume Size panes This section describes components of the Customized Volume pane. Customized Volume pane To open the Customized Volume pane: 1. Click the Volume Manager button ( ). The Volume Manager pane appears. 2. Click the Customized Volume tab. The Customized Volume pane appears. Figure 90 Customized Volume pane Parity Group - LDEV tree Displays the hierarchical structure of an array.
NOTE: If a parity group number starts with V (for example, V1-1), the parity group consists of one or more virtual volumes (V-VOLs). NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU. For more information about external LUs, see the HP StorageWorks External Storage XP user guide. NOTE: The RAID level is left unspecified with a hyphen (-) when the LDEV is an external LU. The following icons indicate parity group status.
NOTE: When free spaces appear in the Parity Group - LDEV table, you can convert any of them into a customized volume (CV). To convert free spaces, right-click a free space, and select Install CV. For more information, see Creating CVS volumes (Install CV operation). NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU. For more information about external LUs, see the HP StorageWorks External Storage XP user guide.
Table 36 Volume status Status Description Normal Volume is in a normal status. Blocked Volume is in a blocked status. Hosts cannot access the blocked volume. Warning Volume has a problem. Format Volume is being formatted. Correction Access Volume's access attribute is being changed. Copying Volume's data is being copied. Read Only Hosts can only read the volume. Hosts cannot write data to a volume in Read Only status. Shredding Shredding operation is in progress.
Figure 91 Volume to Space Confirmation pane • VDEV information table: Displays information about volumes that will be converted to space areas. • VDEV: Set of a disk group, parity group, and VDEV number. NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the parity group consists of one or more external LUs. • CU:LDEV: CU and LDEV numbers. NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU.
Figure 92 Install CV pane (1) for OPEN-V The Install CV pane (1) has the following features: • Parity Group: Selected free space's VDEV number. The VDEV number indicates the parity group where the VDEV belongs. For example, if VDEV number 1-1-(1) appears, the VDEV belongs to parity group number 1-1. NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs.
• • • • • • • • • • Block: Blocks. This unit is used for specifying the capacity of external LUs. For more information about external LUs, see the HP StorageWorks External Storage XP user guide. Specify capacity and number: Capacity and number of CVs in the CVS volume you want to create. • Capacity: CVS volume's capacity in the unit selected in the Capacity Unit list. The available capacity range (minimum - maximum) is shown on the right (for example, 46 - 6720 MB, 50 - 7168 Cyl, or 315 - 8513 blocks).
Figure 93 Install CV pane (1) for other than OPEN-V This pane has the following features: • Parity Group: Selected free space's VDEV number. NOTE: If a parity group number starts with E (for example, E1-1), the parity group consists of one or more external LUs. NOTE: If a VDEV number starts with V (for example, V1-1-(1)), the VDEV belongs to a parity group that consists of one or more virtual volumes (V-VOLs). • Emulation Type: Emulation type.
Install CV pane (2) This pane displays the CVS volumes to be created in the table on the top. You can specify the CVS volume's CU and LDEV numbers. Figure 94 Install CV pane (2) This pane has the following features: • CVS volume-setting information table: On the upper right of the pane, displays detailed information about the CVS volumes to be created. • Parity Group: Number of the VDEV to which the CVS volume belongs. The VDEV number indicates the parity group where the VDEV belongs.
• CU:LDEV: CU and LDEV numbers for the CVS volume to be created. The default is blank. NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU. For more information about external LUs, see the HP StorageWorks External Storage XP user guide. • Select LDEV No. area: Used to set LDEV numbers for the CVS volumes you are creating. • Select CU No.: Select a CU number from the drop-down list. The default is CU 00.
• If the selected LDEV number's boundary area does not have an SSID, the Install CV pane (3) for setting an SSID appears. • If the selected LDEV's boundary area has an SSID, the Install CV pane (4) appears. • Cancel: Cancels the LDEV's settings, and returns to the Customized Volume pane. • Clear: Removes a CU:LDEV number that is already assigned. To remove a CU:LDEV number, right-click the CVS volume number corresponding to the CU:LDEV number you want to remove, and select Clear.
• LDEV Boundary: Boundary area of an LDEV number with no SSID. • SSID: Specified SSID. The default is blank. • Input SSID: Used to select or enter the desired SSID. You can enter the SSID only when you log in as a storage administrator. • SSID number of another SLPR is used: When selected, you can select the number of an SSID that does not exist in the SLPR to which the parity group does not belong. When cleared, you can only select the number of an SSID in the SLPR to which the parity group belongs.
NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs. NOTE: If a VDEV number starts with V (for example, V1-1-(1)), the VDEV belongs to a parity group that consists of one or more virtual volumes (V-VOLs). • Emulation: Emulation type of the CVS volume to be created. • Capacity: CVS volume's capacity displayed in the unit selected from the Capacity Unit list in the Install CV pane (1).
Figure 97 Make Volume pane (1) for OPEN-V This pane has the following features: • Parity Group: VDEV number of the CVS volume to be initialized. The VDEV number indicates the parity group where the VDEV belongs. For example, if VDEV number 1-1-(1) appears, the VDEV belongs to parity group number 1-1. NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs.
• Specify capacity and number: Used to specify the capacity and the number of CVs in the CVS volume you want to create. • Capacity: CVS volume's capacity in the unit selected in the Capacity Unit list. The available capacity range (minimum - maximum) is shown below Capacity Unit (for example, 46 - 6720 MB, 50 - 7168 Cyl, or 315 - 8513 blocks). • Number: Number of volumes of that size. The available range is shown on the right to the box (for example, 1 - 489).
Figure 98 Make Volume pane (1) for other than OPEN-V This pane has the following features: • Parity Group: Selected free space's VDEV number. The VDEV number indicates the parity group where the VDEV belongs. For example, if VDEV number 1-1-(1) appears, the VDEV belongs to parity group number 1-1. NOTE: If a parity group number starts with E (for example, E1-1), the parity group consists of one or more external LUs.
• Cancel: Cancels the selected settings, and returns to the Customized Volume pane. Make Volume pane (2) Use this pane to assign CU and LDEV numbers for the CVS volumes to be created. Figure 99 Make Volume pane (2) This pane has the following features: • CVS volume-setting information table: On the upper right of the pane, displays detailed information about the CVS volumes to be created. • Parity Group: Number of the VDEV to be initialized.
NOTE: If an LDEV number ends with # (for example, 00:01#), the LDEV is an external LU. For more information about external LUs, see the HP StorageWorks External Storage XP user guide. NOTE: If an LDEV number ends with V (for example, 00:00V), the LDEV is a virtual volume (V-VOL). For more information about virtual volumes, see the HP StorageWorks Snapshot XP user guide. • Select LDEV No. area: Used to set LDEV numbers for the CVS volumes you are creating. • Select CU No.: CU number. The default is CU 00.
• If the selected LDEV number's boundary area does not have an SSID, the Make Volume pane (3) for setting an SSID appears. • If the selected LDEV number's boundary area has an SSID, the Make Volume pane (4) appears. • Cancel: Cancels the settings for the LDEV, and returns to the Customized Volume pane. • Clear: Removes a CU:LDEV number that is already assigned. To remove a CU:LDEV number, right-click a CVS volume number corresponding to the CU:LDEV number you want to remove, and select Clear.
• LDEV Boundary: Boundary area of an LDEV number with no SSID. • SSID: Specified SSID. The default is blank. • Input SSID: Used to select or enter the SSID. You can enter the SSID only when you log in as a storage administrator. • SSID number of another SLPR is used: When selected, you can select the number of an SSID that does not exist in the SLPR to which the parity group does not belong. When cleared, you can select only the number of an SSID in the SLPR to which the parity group belongs.
NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs. NOTE: If a VDEV number starts with V (for example, V1-1-(1)), the VDEV belongs to a parity group that consists of one or more virtual volumes (V-VOLs). • Emulation: Emulation type of the CVS volume to be created (OPEN-V). • Capacity: CVS volume's capacity displayed in the unit selected from the Capacity Unit list in the Make Volume pane (1).
• Normal volume-setting information table: On the upper right of the pane, displays detailed information about the CVS volumes to be initialized. • Parity Group: Number of the VDEV to be initialized. The VDEV number indicates the parity group where the VDEV belongs. For example, if VDEV number 1-1-(1) appears, the VDEV belongs to parity group number 1-1. NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs.
• CU number of another SLPR is used: When selected, you can select the number of an LDEV that does not exist in the SLPR to which the parity group does not belong. When cleared, you can only select the number of an LDEV in the SLPR to which the parity group belongs. NOTE: The CU number of another SLPR is used check box appears only when you log in as a storage administrator and when there are two or more SLPRs.
Table 41 Set SSID tree icons (Volume Initialize) Icon Description CU number is not extracted. CU number is extracted. LDEV boundary area. • Set SSID table: Used to set the SSID boundary area. • CU: CU number containing an LDEV boundary with no SSID. • LDEV Boundary: Boundary area of an LDEV number with no SSID. • SSID: Specified SSID. The default is blank. • Input SSID: Used to select or enter the SSID. You can enter the SSID only when you log in as a storage administrator.
Figure 104 Volume Initialize pane (3) for confirming Volume Initialize settings This pane has the following features: • CVS volume-setting information table: Displays a list of the CVS volumes to be initialized. • VDEV: VDEV number for the CVS volume to be initialized. NOTE: If a VDEV number starts with E (for example, E1-1-(1)), the VDEV belongs to a parity group that consists of one or more external LUs.
Concatenation List pane In the array, data can be written to an LDEV that extends over concatenated parity groups. Concatenation of parity groups enables faster access to data. The Concatenation List pane displays concatenated parity groups. Figure 105 Concatenation List pane • Parity Group: Displays concatenated parity groups. NOTE: If a parity group number starts with E (for example, E1-1), the parity group consists of one or more external LUs.
Figure 106 Format All pane CAUTION: The Format All panel does not display virtual volumes. • Parity Group Type: Used to specify volumes to be formatted. • All Type: Blocked volumes in all parity groups in the local and external arrays are formatted. • Internal PG: Blocked volumes in all parity groups in the local array are formatted. • External PG: Blocked volumes in all parity groups in the external array are formatted. • List: Displays information about volumes to be formatted.
Figure 107 Write to Control Blocks pane • Target ExG: External LU groups containing volumes to be made usable. • ExG: External LU group numbers. • External Storage: Information about external arrays. • Add: Moves external LU groups selected in the Candidate ExG list to the Target ExG list. • Delete: Moves external LU groups selected in the Target ExG list to the Candidate ExG list. • Candidate ExG: List of external LU groups. • ExG: External LU group numbers.
• Viewing VDEV and LDEV configuration information You can view configuration information for VDEVs and LDEVs on the Customized Volume pane (Figure 90). This pane shows an outline of group numbers, parity group numbers, RAID levels, and VDEV numbers and a table of CU:LDEV numbers, emulation types, LDEV capacities, and path settings of VDEVs selected in the tree.
NOTE: To select two or more adjacent LDEVs, select the LDEVs while pressing the Shift key. To select two or more discrete LDEVs, select the LDEVs while pressing the Ctrl key. 5. Right-click the selected LDEVs, and select Volume to Space. The Volume to Space Confirmation dialog box appears. 6. If the listed volumes are correct, click OK. The change is not yet implemented in the array, but the following changes appear on the Customized Volume pane: • Selected LDEVs are listed as Free.
• • • • Specify capacity and number Divide free space by number Divide free space by capacity Set remaining space as volume. NOTE: If there are two or more free spaces in the VDEV, Divide free space by number, Divide free space by capacity, and Set remaining space as volume are not available. c. Specify the CVS volume's capacity or the number of CVs according to the selected method.
7. Select one or more CVS volume numbers to assign CU and LDEV numbers. 8. In the Select CU No. list, select a CU number. 9. In the Select LDEV No. table, select an LDEV number from the white LDEV numbers. Gray indicates LDEV numbers that are not selectable, white indicates unused LDEV numbers, and blue indicates available LDEV numbers. The CU and LDEV numbers appear in the CU:LDEV field of the CVS volume-setting information table.
Deleting CVS volumes To delete an individual CVS volume within a VDEV, use the Volume to Space operation (see Converting logical volumes to space ). Converting CVs back to FVs (Volume Initialize operation) CAUTION: The Volume Initialize function is a destructive operation. Data on the CVS volume being converted is lost when the operation is complete. You are responsible for backing up data as needed before performing this operation.
If the selected LDEV number's boundary area does not have an SSID, the SSID setting pane appears. Go to step 8. If the selected LDEV number's boundary area has an SSID, go to step 10. 6. On the SSID setting pane, select the CU number. 7. In the Input SSID list, select a new SSID. NOTE: When you log in as a storage administrator and the SSID number of another SLPR is used check box is selected, you can also enter an SSID in the Input SSID list. 8. Click Set.
1. On the upper right of the XP Remote Web Console main pane, select a CU group from the drop-down list. 2. From the Customized Volume pane, select the LDEV folder in the Parity Group - LDEV tree to display a list of VDEVs, and select a VDEV for OPEN-V. The LDEV Information table displays detailed information about the LDEVs.
c. Click Set to display the setting in the LDEV information table. To remove CVS volume settings displayed in the LDEV information table, do the following: • To remove a setting, select the CVS volume, and click Delete. When a confirmation message appears, select OK. • To remove all settings, click Clear. When a confirmation message displays, click OK. d. To create other CVS volumes, repeat step 5a through step 5c. After setting all CVS volumes, go to step 6. 6. Click Next.
NOTE: Setting changes are not yet implemented in the array. You cannot manipulate VDEVs denoted by blue icons until you click Apply to apply the changes to the array or Cancel to cancel them, but you can initialize additional CVS volumes in VDEVs denoted by red icons. 18. To apply changes to the array, click Apply (or Cancel to cancel them). NOTE: If desired, you can make settings on the Volume Initialize function (see Converting CVs back to FVs (Volume Initialize operation)) before clicking Apply.
• To format all blocked internal LUs, right-click LDEV at the top of the tree, and select Format All. In the Format All pane, select Internal PG from the Parity Group Type list. Confirm that the list displays internal LUs to be formatted, and click OK. • To format all blocked external LUs, right-click LDEV at the top of the tree, and select Format All. In the Format All pane, select External PG from the Parity Group Type list. Confirm that the list displays external LUs to be formatted, and click OK. 9.
To overwrite control blocks in volumes in an external LU group: 1. On the upper right of the XP Remote Web Console main pane, select a CU group from the drop-down list. 2. From the Customized Volume pane, right-click the LDEV folder at the top of the tree, and select Write to Control Blocks. 3. In the Write to Control Blocks pane, select the desired external LU group from the Candidate ExG list, and click Add. The selected external LU group moves to the Target ExG list.
Custom Volume Size operations
11 Troubleshooting Volume Manager and Custom Volume Size • For troubleshooting information about an array, see the array's documentation. • For troubleshooting information about Command View XP or XP Remote Web Console, see the HP StorageWorks Command View XP user guide for XP Disk Arrays or the HP StorageWorks XP Remote Web Console user guide for XP12000/XP10000/SVS200.
Troubleshooting Volume Manager and Custom Volume Size
Index Symbols 16-port channel adapters, serial numbers and names, 38 4-port channel adapters, serial numbers and names, 31 8-port channel adapters, serial numbers and names, 34 A Add iSCSI name button, 66 Add LU Path button, 67 Add WWN button, 66 addresses, Fibre Channel ports, 27, 109 AIX environments server host modes, 82 WWNs, findings, 137 AL-PA addresses, 27 alternate paths defining, 102 limitations, 57 viewing, 104 arbitrated loop physical address (AL-PA), 27 audience, 13 authentication Port Inform
deleting CVS volumes, 205 host bus adapters, 100 host groups, 95 iSCSI names, 101 iSCSI targets, 96 LU paths, 91 WWNs, 101 disabling LUN security, 24, 106 document conventions, 14 prerequisites, 13 related documentation, 13 documentation HP website, 13 providing feedback, 15 DYNIX host modes, 82 E emulation types CV capacities, 147 CVS specifications, 146 groups, 182 management area capacities, 151 slot capacities, 152 SSID requirements, 153 enabling LUN Manager, 57 LUN security, 24, 105 expanded LDEVs, 1
host groups associating to logical volumes, 90 authentication, enabling and disabling, 115 clearing user information, 119 configuring, 19 creating, 80 deleting, 95 deleting host bus adapters, 100 initializing group 0, 96 mode, changing, 93 name, changing, 93 registering hosts in, 86 registering user information, 115 Host list, 78 host user information, Fibre Channel environments changing, 116 deleting, 117 specifying, 118 host user information, iSCSI environments changing, 126 clearing, 129 deleting, 127 re
LDEVs associating host groups to logical volumes, 90 command devices, 26, 107 Concatenation List pane, 165, 198 expanded, 162, 167, 168, 169 formatting, 209 free, 161, 167, 168, 169 Information table, 159 Information tree, 159 LUN Path table, 64 LUSE volume capacity, changing, 170 LUSE volumes, creating with LDEV Information table, 169 Select an LDEV list, 168 Volume Count list, 167 parity group tree, 173 path-defined, 141 releasing a LUSE volume, 170 resetting an unregistered volume, 170 restrictions, 140
overwriting control blocks, 211 P Package tree, 68 parity groups concatenated, 101, 167, 201 Concatenation List pane, 165, 198 configuration, 143 Format All pane, 198 status icons, 173 pinging iSCSI hosts, 45, 71 point-to-point topology, 26 Port Information list, 77 Port pane, 67 port serial numbers 16-port channel adapters, 38 4-port channel adapters, 31 8-port channel adapters, 34 XP10000/SVS200, 43 port statuses Fibre Channel, 60 iSCSI, 63 NAS, 61 Port table, 69 ports alternate paths, defining, 102 Cha
status channel adapter packages, 69 Fibre Channel ports, 60 iSCSI connection, 45, 113 iSCSI ports, 63 LDEVs, 65, 175 LUN icons, 63 NAS channel adapters, 55 NAS ports, 61 parity groups, 174 VDEV, 174 volume, 176 Subscriber's Choice, HP, 15 Sun Solaris, finding WWNs, 136 switch authentication, Fibre Channel environments, 49, 77, 120, 122 system requirements CVS and Volume Manager, 155 LUN Manager, 57 T Target list, authentication, 77 targets, creating iSCSI, 84 technical support HP, 14 service locator websi