HP Integrity Virtual Server Manager 6.2 User Guide
Table Of Contents
- HP Integrity Virtual Server Manager 6.2 User Guide
- Contents
- 1 Introduction
- 2 Installing Integrity Virtual Server Manager
- 3 Accessing and Navigating Integrity Virtual Server Manager
- 4 Using Integrity Virtual Server Manager views and tabs
- 5 Using Integrity Virtual Server Manager menus
- 6 Working with VMs or vPars
- Working with VMs
- Planning VMs
- Creating VMs
- Modifying VMs
- Starting VMs
- Stopping VMs
- Restarting VMs
- Deleting VMs
- Migrating VMs
- Suspending VMs
- Resuming VMs
- Moving suspend files
- Creating virtual switches
- Starting, stopping, and deleting virtual switches
- Deleting network or storage devices
- Opening iLO console
- Opening virtual iLO remote console
- Deleting virtual iLO remote console
- Deleting DIOs
- Adding DIOs
- Replacing DIO H/W path
- Replacing DIO MAC address
- Working with vPars
- Creating vPars
- Modifying vPars
- Booting vPars
- Stopping vPars
- Resetting vPars
- Creating virtual switches
- Starting, stopping, and deleting virtual switches
- Deleting network or storage devices
- Deleting vPars
- Opening iLO console
- Opening virtual iLO remote console
- Deleting virtual iLO remote console
- Adding DIOs
- Replacing DIO H/W path
- Replacing DIO MAC address
- Deleting DIOs
- Working with VMs
- 7 Collecting and viewing utilization data
- 8 Viewing logs and version information
- 9 Support and other resources
- Information to collect before contacting HP
- How to contact HP
- Security bulletin and alert policy for non-HP owned software components
- Subscription service
- Registering for software technical support and update service
- How to use your software technical support and update
- HP authorized resellers
- New and changed information in this edition
- Related information
- Typographic conventions
- 10 Documentation feedback
- A Error messages, status indicators, and troubleshooting
- Glossary
- Index
reboots a vPar that is already booted, while the Boot function does not (it leaves the booted vPar
as it is).
You can use the Reset function instead of the Boot function when you have several vPars that you
want newly booted, some of which are already booted and some currently stopped. The Reset
function resets all the vPars. However, if you do not want the already booted partitions rebooted,
in other words, you just want the stopped partitions booted, use the Boot function instead.
To reset one or more vPars:
1. Click the Virtual Servers tab.
The vPars are listed in this tab.
2. Select one or more vPars by selecting the check box against each required vPar.
3. Select Tools→Reset Virtual Partition from the vPars menu bar.
The Reset Virtual Partition screen is displayed.
Figure 78 Reset vPars
The General Preview area shows the vPars that are going to be reset. The Real Command
area displays the commands that the vPar Manager will execute to reset the selected vPars.
4. Select the How to reset option to set the reset method. The following reset options are available:
• TOC reset: The Transfer of Control (TOC) reset using the -t option does a soft reset of
the selected vPar. The -t option is the default operation of the vparreset command.
For a proper shutdown of the vPar, use the -h option.
• Hard reset: The hard reset or the -h option performs a hard reset of the selected vPar.
The -h option is equivalent to the RS command in the management processor.
5. Click OK to reset the selected vPars.
Creating virtual switches
Create virtual switches menu is applicable for VMs and vPars. For more information about creating
virtual switches, see “Creating virtual switches” (page 102).
Starting, stopping, and deleting virtual switches
For details about starting, stopping, and deleting virtual switches, see “Starting, stopping, and
deleting virtual switches” (page 105).
116 Working with VMs or vPars