Quick Start Guide A7000 dl 1xADSL2+ Annex B Module (J8759A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-2146

ProCurve Secure Router dl 1xADSL2+ Annex B Module

J8759A

INSTALLATION INSTRUCTIONS

Warning

For ProCurve Secure Router modules with outside

plant connections, ensure that all cables are removed

from the module before installing or removing it from

the router chassis.

1. Remove power from the unit.

2. Slide the ProCurve Secure Router dl 1xADSL2+ Annex B Module into

the option slot until the module is firmly seated against the chassis.

3. Secure the screws at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete the installation of the base unit.

6. Restore power to the unit.

ADSL2+ (RJ-11C) PINOUT

Pin Name Description

1-2 — Unused

3 R ADSL Ring

4 T ADSL Tip

5-6 — Unused

Note

An optional backup module is required for backup

applications.

For a description of the backup connection pinouts,

refer to the Quick Start Guide included with your

backup module

SPECIFICATIONS

ADSL2+ Interface

ADSL over ISDN

Supported Standards:

ITU G.992.1 – Annex B (G.dmt)

Connector: RJ-11C (6-pin jack, inner pair)

ATM

Multiple Protocol over AAL5 (RFC2684)

ATM Forum UNI 3.1/4.0 PVC

Up to 16 Virtual Circuits

ATM Class of Service (UBR)

PPP over ATM (RFC2364)

PPP over Ethernet (RFC2516)

ATM F5 OAM

Compliance

FCC Part 15 Class A, EN 55022 Class A, EN 55024,

EN 61000-3-2, EN 61000-3-3

EN 60950, IEC 60950

Physical

Dimensions: 6.99 cm (2.75 inch) W x 10.80 cm

(4.25 inch) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing

at 30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to

158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

Note

For safety information for the routers and all modules,

please refer to the safety and ESD precautions in the

ProCurve Secure Router Installation Guide included

in your router shipment.

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5991-2146 ProCurve Secure Router dl 1xADSL2+ Annex B Module J8759A INSTALLATION INSTRUCTIONS Warning For ProCurve Secure Router modules with outside plant connections, ensure that all cables are removed from the module before installing or removing it from the router chassis. SPECIFICATIONS 1. Remove power from the unit. ADSL2+ Interface 2. Slide the ProCurve Secure Router dl 1xADSL2+ Annex B Module into the option slot until the module is firmly seated against the chassis.
PAGE 2
Quick Start Guide 5991-2146 ProCurve Secure Router dl 1xADSL2+ Annex B Module J8759A ADSL2+ INTERFACE MODULE COMMANDS ATM SUB-INTERFACE COMMANDS retrain Forces the modem to retrain. snr-margin [showtime monitor l training monitor] Enables monitoring and sets the minimum signal-to-noise (SNR) ratio during training and showtime. Use the no form of this command to disable monitoring.