Quick Start Guide A7000 dl 1xADSL2+ Annex B Module (J8759A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-2146

ProCurve Secure Router dl 1xADSL2+ Annex B Module

J8759A

ADSL2+ INTERFACE MODULE COMMANDS

retrain

Forces the modem to retrain.

snr-margin [showtime monitor l training monitor] <margin>

Enables monitoring and sets the minimum signal-to-noise (SNR) ratio during

training and showtime. Use the no form of this command to disable monitoring.

showtime monitor Enables margin monitoring to retrain the ADSL interface

if the specified minimum margin is violated during

showtime.

training monitor Enables margin monitoring to retrain the ADSL interface

if the specified minimum margin is violated during

training.

<margin> Sets the minimum SNR margin in dB. Range is

1 to 15.

training-mode [G.DMT | Multi-Mode]

Configures the ADSL training mode. Additional training modes listed for this

module (G.LITE, T1.413, ADSL2, ADSL2+, READSL2) are for future

implementation. These training modes are currently supported for ADSL over

POTS.

G.DMT Specifies ITU G.992.1 Annex B mode.

Multi-Mode Specifies auto detect mode. This selection defaults to

G.DMT (only valid training-mode for the module).

ATM COMMANDS

snmp trap link-status

Controls the SNMP variable, ifLinkUpDownTrapEnable (RFC2863) to enable the

interface to send SNMP traps when there is an interface status change. Use the

no form of this command to disable this trap.

Note

This command list is an illustration of available

commands. For complete command descriptions and

default values, refer to the SROS Command Line

Interface Reference Guide provided on your

ProCurve SROS Documentation CD.

ATM SUB-INTERFACE COMMANDS

access-policy <policyname>

Applies a specified access policy (previously created using the

(config)# ip policy-class command) to the inbound traffic received on the

interface. Use the no form of this command to remove an access policy

association.

<policyname> Alphanumeric descriptor for identifying the configured

access policy (all access policy descriptors are case-

sensitive). Access policies are created using the

ip policy-class command and descriptors are limited to

255 alphanumeric characters (spaces are not valid).

dynamic-dns [dyndns | dyndns-custom | dyndns-static] <hostname>

Configures Dynamic DNS service provided by Dynamic Network Services, Inc.

(www.dyndns.org).

dyndns Allows you to alias a dynamic IP address to a static

hostname in various domains. This service is provided for

up to five hostnames.

dyndns-custom Gives complete control over an entire domain name. A

Web-based interface provides two levels of control (basic

or advanced) over your domain. Custom DYNDNS can be

used with both static and dynamic IPs.

dyndns-static Allows a hostname such as yourname.dyndns.org to point

to your IP address. This service is provided for up to five

hostnames.

encapsulation [aal5mux | aal5snap]

Configures the encapsulation type for the ATM Adaption Layer (AAL) of the ATM

Protocol Reference Model.

aal5mux Encapsulation type for multiplexed virtual circuits. Specify

the data protocol on the circuit as ip or ppp.

aal5snap Encapsulation type that supports LLC/SNAP protocols.

oam-pvc managed <frequency>

Enables end-to-end F5 Operation, Administration, and Maintenance (OAM)

loopback cell generation and OAM management for an ATM interface.

<frequency> Time delay between transmitting OAM loopback cells.

Range is 0 to 600 seconds.

oam retry <up-count> <down-count> <retry-frequency>

Configures parameters related to OAM management for an ATM interface.

<up-count> Specifies number of consecutive end-to-end F5 OAM

loopback cell responses that must be received in order to

change a PVC connection state to up. Range is 1 to 255.

<down-count> Specifies number of consecutive end-to-end F5 OAM

loopback cell responses that are not received in order to

change a PVC state to down. Range is 1 to 255.

<retry-frequency> Specifies frequency (seconds) that end-to-end F5 OAM

loopback cells are transmitted when a change in the up/

down state of a PVC is being verified. Range is 1 to 600.