Quick Start Guide A7000 dl 1xT1 + DSX-1 Module (J8452A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5990-8893

ProCurve Secure Router dl 1xT1 + DSX-1 Module

J8452A

INSTALLATION INSTRUCTIONS

Warning

For ProCurve Secure Router modules with outside plant

connections, ensure that all cables are removed from the

module before installing or removing it from the router

chassis.

1. Remove power from the unit.

2. Slide the ProCurve Secure Router dl 1xT1 + DSX-1 Module into the

option slot until the module is firmly seated against the chassis.

3. Secure the screws at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete the installation of the base unit.

6. Restore power to the unit.

Note

For safety information for the routers and all modules, please

refer to the safety and ESD precautions in the ProCurve

Secure Router Installation Guide included in your router

shipment.

T1 NETWORK (RJ-48C) CONNECTION PINOUT

Pin Name Description

1 R1 Receive data from the network

2 T1 Receive data from the network

3 — Unused

4 R Transmit data toward the network

5 T Transmit data toward the network

6-8 — Unused

DSX-1 NETWORK (RJ-48C) CONNECTION PINOUT

Pin Name Description

1 R Transmit data toward the DTE

2 T Transmit data toward the DTE

3 — Unused

4 R1 Receive data from the DTE

5 T1 Receive data from the DTE

6-8 — Unused

SPECIFICATIONS

Operating

Modes

T1/FT1 Frame Relay, T1/FT1 PPP, T1/FT1 Multilink PPP,

T1/FT1 Multilink Frame Relay, T1/FT1 HDLC

T1/FT1

Interface

Supported Standards: AT&T TR 62411, AT&T TR 54016,

Bellcore TR 194, ANSI T1.403

Line Rate: 1.544 Mbps ±75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized (multiples of 56/64 kbps)

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB (long), 0 to 655 ft (short)

Connector: RJ-48C

DS0 Assignment: Programmable

DSX-1

Interface

Supported standards: DSX-1 per ANSI T1.102

Line Rate: 1.544 Mbps

DSX Receiver Input Range: -10 dBdsx to +6 dBdsx

Capacity: 1 to 24 DS0s

Line Codes: AMI, B8ZS

DSX-1 interface to PBX

Framing: D4 (SF) or ESF

Line Length: 0 to 655 ft and -7.5 dB

Connector: RJ-48C

Clock Source Network, internal, and through

Diagnostics Test Pattern Generation and Detection: QRSS, 511,

all ones, all zeros

Network loopbacks (local and remote); responds to both

inband and FDL loop codes (T1 interface only)

Alarm generation and detection

Network and user sets of performance data (15 minutes

and 24 hours)

Compliance FCC Part 15 Class A, EN 55022 Class A

ACTA/FCC Part 68, IC CS-03, UL/CUL 60950, IEC 60950

Physical Dimensions: 6.99 cm (2.75 in) W x 10.80 cm (4.25 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing at

30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5990-8893 ProCurve Secure Router dl 1xT1 + DSX-1 Module J8452A INSTALLATION INSTRUCTIONS For ProCurve Secure Router modules with outside plant connections, ensure that all cables are removed from the module before installing or removing it from the router chassis. Warning SPECIFICATIONS 1. Remove power from the unit. Operating Modes T1/FT1 Frame Relay, T1/FT1 PPP, T1/FT1 Multilink PPP, T1/FT1 Multilink Frame Relay, T1/FT1 HDLC 2.
PAGE 2
Quick Start Guide 5990-8893 ProCurve Secure Router dl 1xT1 + DSX-1 Module J8452A 1XT1 + DSX-1 MODULE COMMANDS clock source [line* | internal | through] Configures the source of the clock for the module. The 1xT1 + DSX-1 module supports a single clock source for both T1 interfaces. Use the no form of this command to return to the default value. loopback remote payload Sends a loopback code to the remote unit to initiate a payload loopback. Use the no form of this command to deactivate the loopback.