Quick Start Guide A7000 dl 2xT1 Module (J8453A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-2104

ProCurve Secure Router dl 2xT1 Module

J8453A

SPECIFICATIONS

Operating

Modes

T1/FT1 Frame Relay, T1/FT1 PPP, T1/FT1 Multilink PPP,

T1/FT1 Multilink Frame Relay, T1/FT1 HDLC

T1/FT1

Interface

Supported Standards: AT&T TR 62411, AT&T TR 54016,

Bellcore TR 194, ANSI T1.403

Line Rate: 1.544 Mbps ±75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB

Connector: RJ-48C

DS0 Assignment: Programmable

Clock Source Network, internal, and through

Diagnostics Test pattern Generation and Detection: QRSS, 511,

- 1, 2

- 1, all ones, all zeros

Network loopbacks (local and remote); responds to both

inband and FDL loop codes

Alarm generation and detection

Network and user sets of performance data (15 minutes

and 24 hours)

Compliance FCC Part 15 Class A, EN 55022 Class A, EN 55024,

EN 61000-3-2, EN 61000-3-3

ACTA/FCC Part 68, IC CS-03

UL/CUL 60950, IEC 60950

Physical Dimensions: 6.99 cm (2.75 in) W x 10.80 cm (4.25 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing at

30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

INSTALLATION INSTRUCTIONS

Warning

For ProCurve Secure Router modules with outside plant

connections, ensure that all cables are removed from the

module before installing or removing it from the router

chassis.

1. Remove power from the unit.

2. Slide the ProCurve Secure Router dl 2xT1 Module into the option slot

until the module is firmly seated against the chassis.

3. Secure the screws at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete the installation of the base unit.

6. Restore power to the unit.

Note

For safety information for the routers and all modules,

please refer to the safety and ESD precautions in the

ProCurve Secure Router Installation Guide included in

your router shipment.

T1/1 AND T1/2 NETWORK (RJ-48C) CONNECTION PINOUT

Pin Name Description

1 R1 Receive data from the network - Ring 1

2 T1 Receive data from the network - Tip 1

3 — Unused

4 R Transmit data toward the network - Ring

5 T Transmit data toward the network - Tip

6-8 — Unused

Note

An optional backup module is required for backup

applications.

For a description of the backup connection pinouts, refer

to the Quick Start Guide included with your backup

module

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5991-2104 ProCurve Secure Router dl 2xT1 Module J8453A INSTALLATION INSTRUCTIONS Warning SPECIFICATIONS For ProCurve Secure Router modules with outside plant connections, ensure that all cables are removed from the module before installing or removing it from the router chassis. 1. Remove power from the unit. Operating Modes T1/FT1 Frame Relay, T1/FT1 PPP, T1/FT1 Multilink PPP, T1/FT1 Multilink Frame Relay, T1/FT1 HDLC 2.
PAGE 2
Quick Start Guide 5991-2104 ProCurve Secure Router dl 2xT1 Module J8453A 2XT1 MODULE COMMANDS clock source [line* | internal | through] Configures the source timing used for both T1 interfaces. line* Recovers clock from the primary circuit. internal Provides clocking using the internal oscillator. through Note Recovers clock from the circuit connected to the alternate interface. The 2xT1 module supports a single clock source for both T1 interfaces.