Wireless/Redundant Edge Services xl Module Management and Configuration Guide WS.02.xx and greater

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Switch xl Access Controller Module

651

652

653

654

655

656

657

658

659

660

Table Of Contents

ProCurve Wireless Edge Services xl Module and ProCurve Redundant Wireless Services xl Module
Title Page
Copyright and Disclaimer Notices
Table of Contents
1. Introduction
- Contents
- ProCurve Wireless Edge Services xl Module
- Radio Ports
- Redundancy Groups
- Layer 2 and Layer 3 Roaming Between RPs and Modules
2. Configuring the ProCurve Wireless Edge Services xl Module
- Contents
- Management Interfaces
- Radio Port Adoption
- System Maintenance
- SNMP Traps and Error Reporting
- Radio Port Licenses
- Setting System Information-Name, Time, and Country Code
- Enabling Secure Network Time Protocol (NTP)
- Digital Certificates
3. Radio Port Configuration
- Contents
- Overview
- Country-Code and Regulatory Procedures
- Configuring Radio Settings
  - Creating a Radio Adoption Default Configuration
  - Creating a Radio Configuration for a Particular Radio
- Considerations for Enabling Client Roaming
- Quality of Service (QoS) on RP Radios
  - WMM
  - SpectraLink Voice Priority (SVP)
4. Wireless Local Area Networks (WLANs)
- Contents
- Overview
- Configuration Options: Normal Versus Advanced Mode
  - Normal Mode Configuration
  - Advanced Mode Configuration
- Configuring a WLAN
- VLAN Assignment
  - WLAN-Based VLAN Assignment
    - Considerations for WLAN-Based VLAN Assignment
  - Identity-Based, or Dynamic, VLAN Assignment
- Traffic Management (QoS)
5. Web Authentication for Mobile Users
- Contents
- Overview
- Configuring Web-Auth
- Copying Logo Files to the Module’s Flash
- Configuring Custom Web-Auth Pages
  - Configuring the CGI Commands for the Login Page
  - Configuring the CGI Commands for the Welcome Page
6. IP Services-IP Settings, DHCP, and DNS
- Contents
- IP Settings
- IP Routing
- DNS Client
- DHCP Server
7. Access Control Lists (ACLs)
- Contents
- Overview
- Configuring ACLs
8. Configuring Network Address Translation (NAT)
- Contents
- Overview
- Planning the NAT Configuration
  - Consider Your Company’s Requirements for NAT
  - Record Necessary IP Addresses and Select the NAT Implementation Method
    - Planning the Configuration for Dynamic NAT
    - Planning the Configuration for Static NAT
- Configuring Standard ACLs for Dynamic NAT
- Configuring NAT
9. Fast Layer 2 Roaming and Layer 3 Mobility
- Contents
- Overview
- Configuring Fast Layer 2 Roaming for WPA/WPA2 with 802.1X
- Configuring Layer 3 Mobility
- Verifying and Managing Layer 3 Mobility
  - Monitoring Peers
  - Viewing a Station’s Status
10. Redundancy Groups
- Contents
- High Availability for Wireless Services
- Configuring a Redundancy Group
11. RADIUS Server
- Contents
- Overview
- RADIUS Authentication
  - Configuring the Internal RADIUS Server
  - Enabling Authentication to the Internal Server on a WLAN
- RADIUS Accounting
  - Enabling Accounting to the Internal RADIUS Server on a WLAN
  - Viewing the Internal RADIUS Server’s Accounting Logs
12. Configuring Tunnels with Generic Routing Encapsulation
- Contents
- Overview
- Configuring GRE Tunnels
- Viewing GRE Tunnels and WLAN Mappings
13. Wireless Network Management
- Contents
- Overview
- Monitoring the Wireless Network
- AP Detection
- Configuring Station Intrusion Detection
- Logging and Alarms
  - Configuring Logging
  - Managing the Alarm Log
- MAC Filters (Local MAC Authentication)
- Network Self Healing
  - Neighbor Recovery
  - Interference Avoidance
14. sFlow Agent
- Contents
- Overview
- Configuring sFlow Using the Web Browser Interface
Appendix A - ProCurve Wireless Services xl Module Command Line Reference
- Contents
- Overview
- Manager Commands
- Global Commands
- Interface Commands
- Wireless Commands
- Show Commands
- Show Commands (All Contexts)
- Show Commands (Wireless)
- Support Commands
- Support Commands (All Contexts)
- Support Commands (Wireless)
Index
Back Cover

10-16

Redundancy Groups

Configuring a Redundancy Group

3. Enter the IP address of one of the other modules in the redundancy group.

This address should match the address that you configure for the Interface

IP in the other module’s redundancy group settings.

4. Click the OK button. The module is now listed on the Network Setup >

Redundancy Group > Member screen.

5. Repeat this step for each additional module in the redundancy group.

Enabling Redundancy

After you enable redundancy, the Wireless Edge Services xl Module begins

communicating with other modules and establishing the redundancy group.

Completely configure the redundancy group before enabling redundancy.

After you enable redundancy, you can no longer alter settings or add new

members.

Follow these steps:

1. Click the Configuration tab to return to the Network Setup > Redundancy

Group > Configuration screen.

2. Check the Enable Redundancy box. The redundancy group configuration

options are now dimmed. You also cannot change the member configura-

tion (on the Member tab) while redundancy is enabled.