HP StorageWorks XP24000 Remote Web Console Error Codes Part number: AE131-96004 First edition: June 2007
Legal and notice information © Copyright 2007 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . Intended Audience . . . . . . . . . . Related Documentation . . . . . . . . Document Conventions . . . . . . . . Conventions for Storage Capacity Values Window Illustrations . . . . . . . . . HP Technical Support . . . . . . . . . Subscription Service . . . . . . . . . HP Websites . . . . . . . . . . . . Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 4 1 ..Sample Message Window (Information Level Message) . . . . . . . . . . . . . . . . 9 2 ..Message Window Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 ..Document Conventions . ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..Error Codes — Part Code ..
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 6 ..Error Codes — Part Code 5205 ..Error Codes — Part Code 5210 ..Error Codes — Part Code 5305 ..Error Codes — Part Code 5307 ..Error Codes — Part Code 5310 ..Error Codes — Part Code 6005 ..Error Codes — Part Code 6007 ..Error Codes — Part Code 6010 ..Error Codes — Part Code 6105 ..Error Codes — Part Code 6505 ..Error Codes — Part Code 6507 ..Error Codes — Part Code 6510 ..
About this Guide This document lists the error codes and error messages for the HP Remote Web Console for HP storage system , and provides recommended action for the error conditions. The term storage system in this guide refers to an HP StorageWorks XP24000 Disk Array. Intended Audience This document assumes that the user: • Has a background in data processing and understands direct-access storage device (DASD) systems and their basic functions. • Is familiar with the HP storage subsystem.
HP XP storage systems use the following values to calculate logical storage capacity values (logical devices): • • • • • 1 1 1 1 1 KB (kilobyte) = 1,024 bytes MB (megabyte) = 1,0242 bytes GB (gigabyte) = 1,0243 bytes TB (terabyte) = 1,0244 bytes block = 512 bytes Window Illustrations The windows shown in this guide were displayed on a Windows computer with the Internet Explorer browser. The windows may appear different on your computer depending on the operating system and browser being used.
1 HP StorageWorks XP Remote Web Console for Storage System Messages and Error Codes Remote Web Console for Storage System Messages “Sample Message Window (Information Level Message)” on page 9 shows a typical message window displayed by the HP Remote Web Console for HP storage system software.
• The word R-VOL in TrueCopy for Mainframe messages is equivalent to S-VOL in Continuous Access messages. • Part code: The ID of the application that issued the message. In “Sample Message Window (Information Level Message)” on page 9 the part code is 110. • Message number: Decimal number within the range of 0000 to 99999. In “Sample Message Window (Information Level Message)” on page 9 the message number is 9102.
Part Code Error Number Error Message Recommended Action 1001 A time-out error occurred. Please wait for the SVP to reboot, and then retry the operation. 0001 0001 Severity Level Failure Level The SVP reboots automatically. If the same error occurs despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 0001 4003 An error occurred. If this problem persists, please call technical support. 0001 4004 0001 Severity Level Failure Level Input the correct user name and log in again. E 2 An error occurred. If this problem persists, please call technical support. Input the correct password and log in again. E 2 4005 The user ID is already logged in.
Part Code Error Number Error Message Recommended Action 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 0001 0001 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 5132 The specified user ID is already logged on, or the previous logon was not properly terminated. Please try again later. (By default, the session/RMI time-out is one minute.) Log on with other user's ID.
Part Code Error Number Error Message Recommended Action 5517 An error occurred during SVP processing. If this problem persists, please call technical support. 0001 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 5518 An error occurred during SVP processing. If this problem persists, please call technical support. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 0001 5556 The password is invalid. Check the setting, and then retry the operation. 0001 Severity Level Failure Level The password is invalid. Check the setting, then retry the operation. E 2 5557 The specified permission flag is invalid. Check the setting, and then retry the operation. The specified permission flag is invalid. Check the setting, then retry the operation. E 2 0001 5559 The specified authority flag is invalid.
Part Code Error Number Error Message Recommended Action 0001 6022 A file open error has occurred. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 6023 Failed to access the file. Check the setting, and then retry the operation. If the same problem persists despite retrying, please call technical support. Failed to access the file. Check the setting, then retry the operation.
Part Code 0001 0001 0001 Error Number Error Message Recommended Action 56545 The operation failed because the audit log is being processed. Please wait for a while, and then retry the operation. Severity Level Failure Level Please wait a while, then retry the operation. W 5 57106 An invalid value is included in the management file of the audit log. Please retry the operation. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 2008 An error occurred during SVP processing. If this problem persists, please call technical support. 0002 Severity Level Failure Level If nothing changes despite retrying, call technical support. E 3 2009 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists call technical support. E 2 0002 2010 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5130 0002 0002 Severity Level Failure Level A sequence error occurred. Please call the developer of the client program. Connection is terminated from the server due to the network failure etc. Please log on again. This error might occur and remain internally in the unlock function log when a user in View mode selects the Exit button, but this is not a problem. In other cases, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0002 6502 Now processing. Please wait a while, and then retry the operation. Please log in again after a while. i 0 0002 6531 The SVP is busy. Please wait for a while, and then retry the operation. If the same problem persists despite retrying, call technical support. E 3 0002 7030 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number 0002 0002 0002 Error Message Recommended Action 56526 The resources of other SLPR(s) cannot be accessed. Severity Level Failure Level Correct the settings, then retry the operation. E 6 58578 An error occurred in the storage system. The configuration may be inconsistent. Please select [All Refresh] and refresh the configuration. Click [All Refresh] and refresh the configuration.
Part Code 0003 0003 Error Number Error Message Recommended Action 1005 The following volumes cannot be specified when you change path configurations: • Volumes that do not exist • Volumes other than top LUs in expanded LUs • Volumes reserved by Auto LUN • Volumes to which the Just in Time Storage function is applied 1007 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again.
Part Code 0003 0003 0003 0003 Error Number 1015 1018 1020 1021 Error Message Recommended Action Severity Level Failure Level LU path is set to the releasing expanded LU. (You need to release the expanded LU and path at the same time.) The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 An error occurred. If this problem persists, please call technical support. The specified port does not exist.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. Fibre topology information is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 The specified LU path does not exist. The Configuration information has been already changed.
Part Code Error Number Error Message Recommended Action 1035 An error occurred during SVP processing. If this problem persists, please call technical support. 1036 Severity Level Failure Level If this problem persists, call technical support. E 2 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 The free space remaining in the parity group is not enough to install a customized volume (CV).
Part Code Error Number Error Message Recommended Action 1046 An error occurred during SVP processing. If this problem persists, please call technical support. 0003 0003 Severity Level Failure Level If this problem persists, call technical support. E 2 1048 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 1049 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 1064 You are trying to register the same WWN as the already registered one. Please check the settings and request the setting of the configuration information again. 1065 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 The specified host name or the host group name is already registered.
Part Code Error Number Error Message Recommended Action 1104 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 1105 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action Severity Level Failure Level The command device setting and the command device security setting are incorrect. You cannot do any of the following to the same volume: • Specify the volume as a command device and disable command device security on the volume. • Specify the volume as a non-command device and enable command device security on the volume.
Part Code 0003 0003 0003 0003 0003 0003 0003 30 Error Number Error Message Recommended Action 1130 You cannot specify the default nickname when setting the nickname of a host group or a host. Severity Level Failure Level Correct the specified contents, and request again. E 6 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 0003 1137 Failed to form a LUSE volume because the number of LUSE volumes exceeds the maximum that can be set in a disk array subsystem. 0003 1138 An error occurred. If this problem persists, please call technical support. An error occurred.
Part Code Error Number Error Message Recommended Action 0003 1174 The specified host ID is already registered. 0003 1175 0003 Severity Level Failure Level Please correct the settings, then retry. E 6 Fibre port settings cannot be made to an iSCSI port. Please correct the settings, then retry. E 6 1176 High-speed mode cannot be set to iSCSI packages. Please correct the settings, then retry. E 6 0003 1177 The specified host is already registered.
Part Code Error Number Error Message Recommended Action 1192 When a path is defined from an iSCSI port to a volume, the volume cannot be configured as a command device. Also, paths cannot be defined from iSCSI ports to command devices. Severity Level Failure Level Please correct the settings, then retry. E 6 1193 You cannot add paths to Continuous Access/Business Copy/Cross-system Copy pair volumes. Please correct the settings, then retry.
Part Code Error Number 0003 1350 Error Message Recommended Action You could not add the path to the initiator or external port. Severity Level Failure Level To add a path, change the attribute of the specified port to Target or RCU Target. E 6 1351 The high-speed or initiator/external mix mode cannot be set to the specified port because of the attribute of the port.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Enable the Cache mode of this volume, then retry the operation, or remove the volume from the volumes to be set. E 2 0003 1359 Cache Residency Manager cannot be set for this volume because its Cache mode is set to Disable. 0003 1360 A Cross-system Copy volume cannot be defined as a system LU. Specify a volume that you can define as a system LU, then retry the operation.
Part Code Error Number Error Message Recommended Action 1604 The specified function is not available because it requires Cache Residency Manager. Severity Level Failure Level Please install the required program product. E 6 1613 Program products are not installed on the specified volume. Install the LUN Manager program product and the Open Volume Management program product. i 6 0003 1900 Maintenance operation is being executed by the SVP.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Correct the settings, then retry the operation. E 6 0003 1915 The specified LDEV number is invalid. The LDEV number of the CU group which is not set in CHA cannot be specified. 0003 1916 You cannot set the volumes in the same parity group across multiple CU groups. Correct the settings, then retry the operation. E 6 0003 1917 The volume(s) in CLPR cannot be set across multiple CU groups.
Part Code Error Number Error Message Recommended Action 2010 The LDEV is being used by the host, or an error occurred during SVP processing. Recovery processing may take about 1 minute. Please wait for a while. Severity Level Failure Level Check if the host is performing I/O operations on the target path or volume. E 6 2011 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs).
Part Code 0003 0003 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action The current Cache Residency Manager setting cannot be changed because the prestaging operation is in progress. Please wait for a while, and then retry the operation. 2080 2081 Severity Level Failure Level Please wait a while, then retry the operation. E 6 Prestaging not completed. Wait a while, and click [Refresh], then change the same configuration again.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Take the storage system offline from the host. W 6 0003 2087 The system is online to the mainframe host. Take the subsystem offline from the host. 0003 2088 The Continuous Access pair is suspended. Add an alternative path. Add an alternative path. W 6 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access. Make sure that there is an alternative path from the MCU.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please wait for a moment and retry. E 6 0003 2095 A maintenance operation is in progress.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2200 The Concurrent Copy or the HP StorageWorks XP for Compatible Extended Remote Copy (XRC) Software operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host. If the Concurrent Copy or the Compatible XRC operation is in progress in the target volumes, cancel the Concurrent Copy job or delete a Compatible XRC pair via the host.
Part Code 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action 2510 No path can be set to the specified volume because the addition of volumes is not finished. Severity Level Failure Level Please call technical support and finish adding volumes. E 6 2515 One of the following is defined: a Continuous Access pair, a HP StorageWorks XP Continuous Access Journal Software pair, or a Universal Replicator for Mainframe pair.
Part Code Error Number Error Message Recommended Action 0003 2520 An Auto LUN pair is defined. Cancel the pair definition, and then retry the operation. 0003 2521 Severity Level Failure Level Cancel the pair definition, then retry the operation. E 6 An Auto LUN pair is defined. Cancel the pair definition, cancel the reserve volume, and then retry the operation. Cancel the pair definition, cancel the reserve volume, then retry the operation. E 6 2522 An Auto LUN reserved volume is defined.
Table 5 Error Codes — Part Code 0004 Part Code Error Number Error Message Recommended Action 2006 An error occurred during SVP processing. If this problem persists, please call technical support. 0004 Severity Level Failure Level If this problem persists, call technical support. E 2 6000 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0004 6001 A time-out error occurred.
Table 6 Error Codes — Part Code 0005 Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 0005 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 0005 5200 This functionality is not available. HP StorageWorks XP SNMP Agent is required. Install the program product. E 6 0005 5201 This functionality is not available. Parallel Access Volume is required.
Table 8 Error Codes — Part Code 0007 Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 0007 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 0007 5301 An error occurred. If this problem persists, please call technical support. An error occurred. If this problem persists, call technical support. E 2 5302 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 0007 6092 An error occurred while reading a file. 0007 0007 Severity Level Failure Level Please call technical support. E 5 6093 The file to be downloaded was not found. The specified file was not found. Please check whether the file exists and retry the operation. W 5 56546 Another user is downloading the file. Please wait for a while, and then retry the operation. Please wait a while, then retry the operation.
Part Code Error Number Error Message Recommended Action 7060 0010 Severity Level Failure Level A client processing error occurred. Please delete the cache file of the browser, restart the browser and log on again. If this problem persists call technical support. E 2 7440 An error occurred during processing. If this problem persists please call technical support. An error occurred. If this problem persists, call technical support. E 2 0010 8101 The system cannot apply the new configuration.
Part Code Error Number Error Message Recommended Action 0010 59013 The specified file already exists. Do you want to overwrite this file? Severity Level Failure Level To overwrite the file, click [OK]. Otherwise, click [Cancel]. W 0 59109 The free space to store the audit log file has run out. The old audit log information is deleted because it is overwritten with the new audit log information. Please download the audit log file.
Part Code Error Number Error Message Recommended Action 2085 Copying is in progress for Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, or Cross-system Copy pairs. Please wait for a while and then retry. 0105 Severity Level Failure Level Please wait a while, then retry. W 6 2086 The configuration of Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, XP Snapshot, or Cross-system Copy has been defined.
Part Code 0105 0105 0105 Error Number Error Message Recommended Action 2093 Some Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs exist. Please resynchronize them. Severity Level Failure Level Please resynchronize the Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs. W 6 2094 Some Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs exist.
Part Code 0105 0105 0105 0105 0105 0105 0105 0105 Error Number Error Message Recommended Action 2202 The specified volume cannot be processed due to the effect of the access attribute assigned by Volume Retention Manager. Check the settings, and then retry the operation. Severity Level Failure Level Check the settings, then retry the operation. E 6 2203 Processing cannot be performed because of HP StorageWorks XP Volume Security settings. Please correct settings, then retry.
Part Code Error Number Error Message Recommended Action 2518 A Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pair is defined. Cancel the pair definition, and then retry the operation. If a reserve volume is defined, cancel it. If a high speed split is in progress, first suspend and then cancel the pair. 0105 Severity Level Failure Level Cancel the pair definition, then retry the operation. If a reserve volume is defined, cancel it.
Part Code Error Number Error Message Recommended Action 6023 An error occurred during SVP processing. If this problem persists, please call technical support. 0105 Severity Level Failure Level If this problem persists, call technical support. E 3 6533 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please resynchronize or release the pair definition of the XP Snapshot pair using the pool volume to be maintained, then retry the operation. E 6 0105 58623 The specified operation cannot be performed, because the XP Snapshot pair using the pool volumes to be maintained is in PSUS status or being restored. Please resynchronize the pair or release the pair definition, and then retry the operation.
Part Code Error Message Recommended Action Severity Level Failure Level 5084 The evaluation license for this product (Remote Web Console) is not installed. Please install. Install Remote Web Console program product. i 5 5085 The maximum permissible capacity of program product became insufficient. Please install additional license key(s) to expand the license capacity of this software title. Please install additional license key(s) to expand the license capacity of this software title.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 i 5 i 0 0110 8201 The system detects an error. Retry the same operation several times. If the same error occurs, call technical support. 0110 9002 The requested operation is complete. Click [OK]. 0110 9100 Do you want to exit? 0110 9101 Do you want to cancel? To cancel, click [OK]. i 0 0110 9102 Do you want to apply? To execute the operation in Preview, click [OK], if not click [Cancel].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please wait for a while, then click [OK] and change the mode to Modify. W 0 0110 59002 The storage system is in internal process, or some other user is changing the configuration. Please wait for a while, then click [OK] and change the mode to Modify. Do you want to retry the operation to change the mode to Modify? 0110 59003 Succeeded to change the mode to Modify. Reply to the message.
Part Code Error Number Error Message Recommended Action 0190 5010 This page can be accessed by the administrator only. None. 0190 5011 The same nickname is already registered. Specify other nickname and register again. 0190 5012 Enter the nickname with up to 16 alphanumeric characters. Specify the nickname using up to 16 characters and less and retry. 0190 5013 Enter the product name with up to 16 alphanumeric characters.
Part Code Error Number Error Message Recommended Action 0190 6001 Failed to open the storage list file. If the same error occurs again despite retrying, call technical support. 0190 6002 Failed to open the storage list file. If the same error occurs again despite retrying, call technical support. 0190 6003 The storage list file does not exist. Please call technical support. 0190 6004 Failed to open the storage list file. If the same error occurs again despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 0190 57004 Specify both the certificate file and the key file. Specify both the certificate file and the key file, then retry the operation. 0190 59304 Are you sure you want to change the setting? Reply to this message. 0190 59305 Are you sure you want to change the setting? Reply to this message.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. W 5 0210 55621 Save the setting by using the setting backup function because you may need to set the Remote Web Console again. 0210 55622 Are you sure you want to register the user? To register the user, click [OK]. Otherwise, click [Cancel]. W 5 0210 55623 Are you sure you want to delete the specified user? To delete the specified user, click [OK]. Otherwise, click [Cancel].
Table 14 Error Codes — Part Code 0290 Part Code Error Number Error Message Recommended Action 0290 5010 Enter the user ID. Specify the user ID. 0290 5014 The user ID or password is invalid. Input the correct user name or password. 0290 5015 Enter the user ID with up to 16 alphanumeric characters. You can specify the user ID with up to 16 characters. 0290 5016 The Password is invalid. Access Denied. Correct the specified content, and retry. 0290 5020 The password is invalid.
Part Code Error Number Error Message Recommended Action Reopen. 0290 6010 The user account list was modified by the administrator while you were making settings. 0290 6020 The user ID was deleted by the administrator. Terminate the process. 0290 6030 Failed to open the user account list file. If the same error occurs again despite retrying, call technical support. 0290 6040 The user account list file does not exist. Please call technical support.
Part Code Error Number Error Message Recommended Action 0290 6200 Failed to open the environment file. If the same error occurs again despite retrying, call technical support. 0290 6210 Failed to open the environment file. If the same error occurs again despite retrying, call technical support. 0290 6220 Failed to back up the environment file. Please call technical support. 0290 6230 Failed to open the user account list file. Please call technical support.
Part Code Error Number Error Message Recommended Action 0290 56121 File name is not specified. Specify the file name, then retry the operation. 0290 56131 File name is not specified. Specify the file name, then retry the operation. 0290 56141 File name is not specified. Specify the file name, then retry the operation. 0290 56211 File Name is invalid. Specify the correct file name, then retry the operation. 0290 56221 File Name is invalid.
Part Code Error Number Error Message Recommended Action 0290 56441 Failed to create the file. If this problem persists, call technical support. 0290 56541 Failed to extract files. If this problem persists, call technical support. 0290 56611 Failed to create the file. If this problem persists, call technical support. 0290 56621 Failed to create the file. If this problem persists, call technical support. 0290 56631 Failed to create the file. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 7202 An error occurred during SVP processing. If this problem persists, please call technical support. 0305 Severity Level Failure Level If this problem persists, call technical support. E 2 7203 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0305 7204 An error occurred during SVP processing.
Table 16 Error Codes — Part Code 0310 Part Code Error Number Error Message Recommended Action 0310 5010 Specify 0 or above but below 256 in each field. 0310 5011 0310 Severity Level Failure Level Correct the specified content, and retry. W 5 0 cannot be specified in all the fields or the ClassA field. Correct the specified content, and retry the operation. W 5 5040 The maximum number of IP Address is 32. Reduce the number, and retry.
Part Code Error Number Error Message Severity Level Failure Level Please install the related program product first. W 5 Recommended Action To install/uninstall this program product, you must install/uninstall another program product first.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 ----------------------------------------------------- 0405 5078 TrueCopy Asyn chronous for Mainframe TrueCopy for Mainframe Universal Replicator for Mainframe TrueCopy for Mainframe Continuous Access Asyn chronous Continuous Access Continuous Access Journal Continuous Access XP Snapshot Business Copy Performance Control Performance Monitor Auto LUN Performance Monitor Disaster Recovery Extended
Part Code Error Number Error Message XP Snapshot Business Copy Performance Control Performance Monitor Auto LUN Performance Monitor Disaster Recovery Extended Universal Replicator for Mainframe Disaster Recovery Extended Continuous Access Journal Recommended Action Severity Level Failure Level 0405 5079 This program product needs another DKC type. Please call technical support. W 5 0405 5080 You cannot change this program product. Please call technical support.
Part Code Error Number Error Message Recommended Action 0405 6022 The SVP is busy. Please wait for a while, and then retry the operation. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 3 6023 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 6517 Serverless Backup is running, but I/O operations might be in progress.
Part Code Error Number Error Message Recommended Action 7205 An error occurred during SVP processing. If this problem persists, please call technical support. 0405 0405 Severity Level Failure Level If this problem persists, call technical support. E 2 7206 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 7207 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 0405 8206 This program product is in use, you cannot uninstall this program. 0405 8301 Severity Level Failure Level Stop using this program product function. W 5 The subsystem status is invalid. Please call technical support. Please retry this operation. E 2 55263 The specified program product cannot be uninstalled, because the license for it is allocated to the SLPR.
Part Code 0405 0405 0405 0405 Error Number Error Message Recommended Action 57098 An error occurred during SVP processing. If this problem persists, please call technical support. 65089 Severity Level Failure Level If this problem persists, call technical support. E 3 The licensed capacity of each SLPR of SLPR1-31 is to be set to 0 GB. Please allocate the licensed capacity if you want to use it continuously. If capacity is not allocated within 30 days, the license of the SLPR becomes invalid.
Part Code Error Number Error Message Recommended Action 0410 5046 The maximum number of filename codes is 200. 0410 0410 Severity Level Failure Level Correct the specified content, and retry. W 5 55000 Since the error occurred in the install or uninstall judging, the applying operation cannot be performed. Acquire the information again, and retry the operation. W 0 55001 The length of the key code is incorrect. Check the length of the key code.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Set the amount of licensed capacity to be reduced less than the total capacity of the storage system or the licensed capacity. E 5 0410 59306 The licensed capacity cannot be reduced because the specified amount of licensed capacity to be reduced exceeds the total capacity of the subsystem or the licensed capacity.
Part Code Error Number Error Message Recommended Action 6040 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 6050 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0505 6502 A time-out error occurred. Please wait for a while, and then retry the operation.
Part Code Error Number Error Message Recommended Action 8100 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. Severity Level Failure Level If the same problem persists despite retrying, please call technical support. E 6 8310 The subsystem status is invalid. Please call technical support. Retry the same operation several times. If this problem persists, call technical support.
Table 22 Error Codes — Part Code 0510 Part Code Error Number 0510 0510 0510 Error Message Recommended Action 7060 An error occurred in the client logic. Severity Level Failure Level If this problem persists, please call HP technical support. E 2 59045 The detailed information will be initialized by this operation. Do you want to continue? To continue processing, click [OK]. To stop processing, click [Cancel].
Part Code Error Number Error Message Recommended Action 2086 Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN or Compatible FlashCopy pair is defined. Release the pair definition, and then retry the operation. 0605 0605 Severity Level Failure Level Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN or Compatible FlashCopy pair is defined. Release the pair definition, then retry the operation. W 3 2087 The system is online to the mainframe host.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the setting, then retry the operation. E 5 0605 2202 The specified volume cannot be processed due to the effect of the access attribute assigned by Volume Retention Manager. Check the settings, and then retry the operation. 0605 2203 Processing cannot be performed because of Volume Security settings. Processing cannot be performed because of Volume Security settings.
Part Code Error Number Error Message Recommended Action 2518 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair or a Compatible FlashCopy pair. Please split the pair and then retry the operation. If a reserve volume is defined, please cancel the reservation. When quick split is in process, suspend and then cancel the pair. 0605 Severity Level Failure Level Cancel the pair definition, then retry the operation. If a reserve volume is defined, cancel it.
Part Code Error Number Error Message Recommended Action 6022 An error occurred during SVP processing. If this problem persists, please call technical support. 0605 0605 Severity Level Failure Level If this problem persists, call technical support. E 3 6023 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 6502 Processing in progress. Please wait for a while, and then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 3 0605 8102 This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. 0605 8122 This logical volume is busy. Please wait a while, then retry the operation. E 5 0605 8136 The command was rejected, because the licensed capacity was exceeded. The currently licensed capacity is insufficient.
Part Code Error Number Error Message Recommended Action 8959 An error occurred on the DKC side. If this problem persists, please call technical support. 0605 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8960 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 8971 An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration. Severity Level Failure Level An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration. E 2 8978 An error occurred on the DKC side.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 0605 55319 The number of data items is invalid. (The definition sentence is not in the spreadsheet.) 0605 55340 There is no entry in an item that requires an entry. Check the contents of the External Storage spreadsheet. E 5 0605 55341 The number of digits is invalid. Check the contents of the External Storage spreadsheet.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 0605 55375 The specified external volume group number is duplicated in the spreadsheet. 0605 55376 The specified external volume group number is already being used. Check the contents of the External Storage spreadsheet. E 5 0605 55377 An unset CLPR number has been specified. Check the contents of the External Storage spreadsheet.
Part Code Error Number Error Message Recommended Action 0605 55391 An unsupported device was specified. 0605 55392 0605 Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 The specified SSID value is already being used. Check the contents of the External Storage spreadsheet. E 5 55393 There is an error in the path settings. Check the contents of the External Storage spreadsheet. E 5 56301 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 56516 The configuration of Continuous Access is defined. Reset the configuration definition of Continuous Access, and then retry the operation. Severity Level Failure Level Reset the configuration definition of Continuous Access, then retry the operation. E 5 56517 The configuration of Business Copy, ShadowImage for Mainframe, Compatible FlashCopy or XP Snapshot is defined.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 5 0605 58246 This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. 0605 58258 All the paths to the external volume are blocked. Restore the blocked path status, then retry the operation. E 5 0605 58263 No paths will be available, if you change the setting of paths.
Part Code 0605 0605 0605 0605 0605 0605 0605 0605 0605 Error Number Error Message Recommended Action 58573 Severity Level Failure Level This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. E 3 58575 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 66013 The specified emulation type cannot be set because 3390-3R is set in the subsystem. Severity Level Failure Level Change the emulation type set in the volume. E 5 66014 The specified emulation type cannot be set because 3390-3 is set in the subsystem. Change the emulation type set in the volume. E 5 66015 The specified path configuration cannot be applied. Check the status of the path, then retry the operation.
Table 24 Error Codes — Part Code 0610 Part Code Error Number Error Message Recommended Action 0610 6505 The number of LUs that can be set to the external volume group exceeds the maximum (4096). 0610 6516 Severity Level Failure Level Please decrease the Volumes that are set to the external volume group, then retry the operation. W 0 R-VOLs exist on the RCU port. Please release the R-VOLs that have been set. W 5 7060 An error occurred during processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. i 0 0610 59020 The setting is insufficient for automatic mapping. Check the setting, and then retry the operation. 0610 59021 The automatic mapping processing was interrupted. Retry the operation. i 0 0610 59022 There are not enough logical volumes to perform the mapping operation. Decrease the number of external volumes to be mapped, then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please correct the licensed capacity with the License Key Partition Definition window. W 5 0610 59057 The licensed capacity was exceeded because of changing the configuration. Please correct the licensed capacity on the License Key Partition Definition window. 0610 59058 Do you want to specify an SSID without restrictions on SLPRs? To continue processing, click [OK]. Otherwise, click [Cancel].
Part Code 0610 0610 0610 0610 0610 Error Number Error Message Recommended Action 69005 Either the emulation types or the SLPR numbers or the both for the multiple external volumes you selected are not the same. When selecting multiple volumes, select the volumes that have the same emulation type and the same SLPR number. Severity Level Failure Level When selecting multiple volumes, select the volumes that have the same emulation type and the same SLPR number.
Part Code 0610 0610 0610 Error Number Error Message Recommended Action 69013 Severity Level Failure Level SSID cannot be allocated. The number of SSID that can be used in the SLPR may be insufficient. Check the setting. W 0 69026 The selected volumes include an external volume that the external volume parameter is already set. Set the configuration in the following [External Volume Parameter] dialog box. Check all items in the [Set External Volume Parameter] dialog box and click [OK].
Table 27 Error Codes — Part Code 1005 Part Code 1005 1005 1005 1005 1005 1005 1005 102 Error Number Error Message Recommended Action Severity Level Failure Level The specified volume cannot be set as a command device or a component of a LUSE volume, because it is being used as a Continuous Access, Business Copy, Cross-system Copy, Auto LUN, or XP Snapshot volume. Select another volume. Select another volume. E 6 You are trying to set multiple paths to the same volume from one group.
Part Code 1005 1005 1005 1005 1005 1005 Error Number 1011 1012 1013 1015 1018 1020 Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. The volume which links as an expanded LU extend over CU#. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 LU path is set to a volume which links as an expanded LU.
Part Code 1005 Error Number 1021 Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. The specified volume does not exist. (You have specified wrong CU#:LDEV#.) Or the LDEV (exclusively for mainframe) cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code 1005 1005 1005 1005 1005 1005 1005 1005 Error Number Error Message Recommended Action 1059 Severity Level Failure Level An error occurred. If this problem persists, please call technical support. You are trying to perform LUN Manager operation for non-Fibre port. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Command device setting is requested for Reserve volume of Auto LUN. Or it is requested for volumes other than open volumes (including uninstalled volumes). The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code 1005 1005 1005 1005 1005 1005 1005 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. CHA high-speed mode is specified to unmounted CHA. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 1128 An error occurred. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. When PORT information (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same PORT. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 1136 An error occurred.
Part Code Error Number Error Message Recommended Action 1005 1178 An incorrect host name was specified. 1005 1180 1005 Severity Level Failure Level Please correct the settings, then retry. E 6 An error occurred. If this problem persists please call technical support. If this problem persists call technical support. E 2 1181 The specified path cannot be added, because the volume is used by a Continuous Access pair. Correct the specification, then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please correct the settings, then retry. E 6 1005 1196 You cannot create a LUSE volume by concatenating LUs and Cross-system Copy LUs. 1005 1197 You cannot set high-speed mode to a package including an external port. Please correct the settings, then retry. E 6 1005 1198 Since a path is defined to an external LU, you cannot set high-speed mode. Please correct the settings, then retry.
Part Code Error Number Error Message Recommended Action 1352 Logical paths remain on the Fibre-MCU port. This operation may cause a fatal damage to the logical paths. Please stop this operation. If you want to continue this operation, please remove the logical paths from the MCU port first. 1005 1005 Severity Level Failure Level Since the port you are trying to set is for Fibre Continuous Access, you must delete the logical path, then retry the port setting.
Part Code Error Number Error Message Recommended Action 1365 External volumes of different drive types (Normal, SATA) cannot be combined to form a LUSE volume. 1005 1005 Severity Level Failure Level Check the settings, then retry the operation. E 2 1367 The host mode 4C is used for a host group connecting to volumes that cannot be used for External Storage. Check the settings, then retry. E 6 1368 The host mode 4C can only be used with External Storage volumes.
Part Code Error Number Error Message Recommended Action 2005 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 2009 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 2010 The LDEV is being used by the host, or an error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 2099 The operation cannot be performed, because an inoperative MP exists. Severity Level Failure Level Wait a while, then retry the operation. If the same problem persists. Please call technical support. E 6 2100 An error occurred while connecting to the storage system. The configuration may be inconsistent. Please select [All Refresh] and refresh the configuration. Click [All Refresh] and refresh the configuration.
Part Code Error Number Error Message Recommended Action 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 1005 Severity Level Failure Level Retry the operation. If this problem persists, call technical support. E 2 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 55553 The specified port is not a fibre port. Check the setting. E 6 1005 55554 The specified WWN is not registered. Check the setting. E 6 1005 55555 The value of the WWN is not specified or is set to zero. Check the setting. E 6 1005 55556 The specified port is not an iSCSI port. Check the setting. E 6 1005 55557 The specified iSCSI name is not registered. Check the setting.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the setting. E 6 1005 55572 The iSCSI name cannot be set because the number of iSCSI names exceeds the maximum that can be set in a port. 1005 55573 The default nickname cannot be specified in the nickname setting of iSCSI name. Correct the settings, then retry the operation.
Part Code Error Number Error Message Recommended Action 58574 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. Severity Level Failure Level If this problem persists, call technical support. E 6 58575 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. If this problem persists, call technical support. E 6 58576 A communication time-out error occurred in the storage system.
Part Code Error Number Error Message Recommended Action 1010 5043 The selected number of LDEVs exceeds the number of free LUNs. 1010 5050 1010 Severity Level Failure Level Reduce the number, and retry. W 5 The specified LUN had been set. Check the content of the operation. W 5 5051 The selected LUN is not a command device. Check the content of the operation. E 3 1010 5052 Select the LUN that is already assigned. Check the content of the operation.
Part Code Error Number Error Message 1010 9014 The LUN will not be specified as a command device. Do you want to continue? 9015 The port of a PCB in High Speed mode/MIX mode is selected. When changing the parameter of topology or the parameter of host speed, the change will be applied to the PCB in High Speed mode/MIX mode. Are you sure you want to continue this operation? 9017 LUN security will be applied to the specified command device.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. W 5 1010 59313 The iSNS IP address or the iSNS port number has been changed. Please delete iSNS information and then select [Apply]. 1010 59314 Do you want to register the iSCSI port information in the iSNS server? To continue processing, click [OK]. To stop processing, click [Cancel].
Part Code Error Number Error Message Recommended Action 1110 5040 The maximum number of Host Groups is already registered. 1110 5041 1110 Severity Level Failure Level You cannot register a host group. W 5 The maximum number of hosts is already registered. Reduce the number, and retry. W 5 5042 The number of LUNs in use has already reached the maximum number of LUNs that can be specified in a port (2,048 in a Fibre Channel environment). Reduce the number, and retry.
Part Code Error Number Error Message Recommended Action 1110 5066 The corresponding port cannot be changed because the security switch is OFF. 1110 5067 1110 Severity Level Failure Level Please check the operation contents. W 5 The corresponding port cannot be changed because the port is an initiator port. Please check the operation contents. W 5 5824 The specified iSCSI name is incorrect. If the type of the iSCSI name is eui, please specify 20 characters.
Part Code Error Number 1110 9061 1110 Error Message Severity Level Failure Level The specified host will be deleted. Do you want to continue? i 0 9063 Warning: The LU path to the LDEV will be released at once.
Part Code Error Number Error Message Recommended Action 55545 The specified Target name is incorrect. If the type of the Target name is eui, please specify the name in 20 characters. The characters can be any combinations of the following, starting with eui.: • numerals (0-9) • letters from A to F, a to f If the type of the Target name is iqn, please specify the name within 223 characters. The characters can be any combinations of the following: • numerals (0-9) • letters from A to Z, a to z • dots (.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 3 because these names are unnecessary. The deleted iSCSI names will not be displayed. Are you sure you want to continue this operation? Table 30 Error Codes — Part Code 1205 Part Code Error Number 1205 6012 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level A communication error occurred while executing the contents of the setting. If the same problem persists despite retrying, check the LAN setting between the SVP and the disk storage system. If this problem persists, call technical support. (Please obtain trace information by using the FD Dump tool.) W 5 58388 PCB for iSCSI is not mounted. Check the settings. If this problem persists, call technical support.
Table 31 Error Codes — Part Code 1310 Part Code Error Number Error Message Recommended Action 1310 5831 The target name is incorrect. 1310 5832 1310 Severity Level Failure Level Correct the settings, then retry the operation. W 5 The user name is incorrect. Correct the settings, then retry the operation. W 5 5833 The secret is incorrect. Correct the settings, then retry the operation. W 5 1310 5834 The reentered secret does not match the previously entered secret.
Part Code Error Number Error Message Recommended Action 2010 5052 This is the last path for the LUSE volume. 2010 5053 2010 Severity Level Failure Level Check the content of the operation. W 5 You should map at least one path to LUSE volume. Check the content of the operation. W 5 5054 More than 36 volumes cannot be combined to form a LUSE. Check the content of the operation. W 5 2010 5055 The size of the LUSE volume exceeds 64,424,505,600 KB.
Part Code 2010 2010 2010 Error Number Error Message Recommended Action 55007 Are you sure you want to perform the LUSE operation using volumes that have different CLPR numbers? Severity Level Failure Level To continue this operation, click [OK]. To cancel this operation, click [Cancel]. W 5 55034 You are trying to combine volumes having different SLPR numbers into a LUSE volume. If you perform this operation, the storage partition administrator will become unable to operate.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Vary the storage system offline from the mainframe host. W 6 3005 2087 The system is online to the mainframe host. Take the subsystem offline from the host. 3005 2088 The Continuous Access pair is suspended. Add an alternative path. Add an alternative path. W 6 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access.
Part Code 3005 Error Number 2095 Error Message Recommended Action A maintenance operation is in progress. For example: • LDEV formatting is in progress • Correction Copy is in progress • Drive Copy is in progress • The CHA/DKA status is changing • The cache status is changing • Replacement of an OEM drive microcode is in progress • LDEV shredding is in progress Therefore the specified operation cannot be executed. Severity Level Failure Level Please wait for a while and retry.
Part Code 3005 3005 3005 3005 3005 3005 Error Number Error Message Recommended Action 2205 Devices to be maintained include journal volumes. Delete all pairs belonging to journal volumes to be maintained. Severity Level Failure Level Devices to be maintained include journal volumes. Delete all pairs belonging to journal volumes to be maintained. E 6 2511 The restore operation has been failed, because the specified LDEV was not shredded or formatted.
Part Code Error Number Error Message Recommended Action 2518 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair, or a Compatible FlashCopy pair. Please split the pair and then retry the operation. If a reserve volume is defined, please cancel the reservation. If the Hi-Speed Split mode is on, please suspend the pair and then split. Severity Level Failure Level Please split the pair and then retry the operation. If a reserve volume is defined, cancel the reservation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Install the required program product. E 6 3005 5874 The program product required for using the shredding function is not installed. 3005 5875 The specified volume is formatting or shredding. Retry later. E 6 3005 6000 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code 3005 3005 3005 3005 3505 3505 3005 3005 3005 3005 136 Error Number Error Message Recommended Action 8000 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 8001 A communication time-out error occurred in the storage system. Please wait for a while, and then retry the operation. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 55509 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 55510 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 55511 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 56302 An error occurred during SVP processing. If this problem persists, please call technical support. 3005 3005 Severity Level Failure Level If this problem persists, call technical support. E 2 56303 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 56524 This function cannot be used by the storage partition administrator.
Part Code Error Number Error Message Recommended Action 3005 58464 The specified logical volume cannot be registered, because it is a V-VOL. Severity Level Failure Level Specify another logical volume. E 6 58465 The volume set as a Command Device cannot be set as a component of a Pool-VOL. Specify another logical volume. E 6 58466 The specified logical volume cannot be registered, because an SCSI path is set to the logical volume. Specify another logical volume.
Part Code 3005 Error Number 58473 Error Message Recommended Action The threshold of pool cannot be changed when: • the threshold is set below the usage rate of the pool. When the pool cannot be deleted, do the following: • check the installation status of the V-VOL management area, when the V-VOL management area is not initialized. • check the installation status of the V-VOL management area, when the V-VOL management area is not installed.
Part Code Error Number Error Message Recommended Action An error occurred during the communication with the storage system. Please wait a while, and retry the operation. If the error occurred in the operation of the pool, please initialize the V-VOL management area, refresh the configuration by clicking [Refresh All] on the File menu, then retry the operation. 58573 Severity Level Failure Level Please wait a while, and retry the operation.
Part Code Error Number Error Message Recommended Action 65671 The pool volumes associated with the XP Thin Provisioning volume is included in the items to be maintained. Release the association of the pool volume and the XP Thin Provisioning volume included in the items to be maintained. 3005 Severity Level Failure Level Release the association of the pool volume and the XP Thin Provisioning volume included in the items to be maintained.
Table 34 Error Codes — Part Code 3010 Part Code Error Number Error Message Recommended Action 1046 The number of Cache Residency Manager settings has exceeded the maximum number of available Cache Residency Manager areas. 3010 Severity Level Failure Level Reduce the number of Cache Residency Manager settings, then retry the operation. W 5 5010 The specified SSID falls out of range. Please specify a valid SSID, and then retry the operation. Correct the specified content, and retry.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the content of the operation. W 5 3010 5055 There is no volume to be initialized.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please log off from Remote Web Console. Then log on to Remote Web Console again and check whether configuration changes have been made correctly. If configuration changes have been made correctly, there is no problem. If configuration changes have been made incorrectly, retry the operation. E 2 The normal end was carried out. Please click [OK] and close the dialog.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. W 0 3010 55033 There is no specifiable LDEV number. Probable causes and solutions are: • The CU number that can be specified for the started SLPR is not assigned. Contact the storage administrator. • All LDEVs in the usable CU are already used. • Check whether the LDEVs are used by another SLPR. Alternatively, contact the storage administrator. 3010 55205 There are no volumes that can be initialized.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level An error occurred in format processing or in Write to Control Blocks processing. Please confirm whether the external volume is zero formatted when an error occurs in Write to Control Blocks processing. Execute zero format processing when the external volume is not zero formatted. Please retry the operation if the error occurred in the format processing. If this problem persists, call technical support.
Part Code 3010 3010 3010 3010 Error Number Error Message Recommended Action 65647 Reset operation cannot be performed because the number of volumes that can be created in the parity group exceeds the maximum. Severity Level Failure Level Reduce the number of volumes in the parity group, then retry the operation. W 5 69029 If the unit of display is changed, the status of the setting will return to the status set before. Do you want to continue? To continue processing, click [OK].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue processing, click [OK]. Otherwise, click [Cancel]. i 5 3110 59601 It will be added to the Pool-VOL table with the specified contents. Do you want to continue? 3110 59602 Are you sure you want to delete the Pool? To continue processing, click [OK]. Otherwise, click [Cancel]. i 5 3110 59603 Are you sure you want to release the blockade of the Pool? To continue processing, click [OK].
Part Code Error Number Error Message Recommended Action 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access. Make sure that there is an alternative path from the MCU. 3205 3205 Severity Level Failure Level Be sure there is an alternative path from the MCU. W 5 2091 The backup server of Business Copy/ ShadowImage for Mainframe/Compatible FlashCopy is running. Please stop the backup server and then retry the operation.
Part Code Error Number Error Message Recommended Action 6022 An error occurred during SVP processing. If this problem persists, please call technical support. 3205 Severity Level Failure Level If this problem persists, call technical support. E 3 6023 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 3205 6533 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 8954 An error occurred on the DKC side. If this problem persists, please call technical support. 3205 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8955 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 8967 An error occurred on the DKC side. If this problem persists, please call technical support. 3205 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8968 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code 3205 Error Number 56520 Error Message Recommended Action FlashCopy, or XP Snapshot exists. Release the reserve volume setting and then retry the operation. Mainframe, Compatible FlashCopy, or XP Snapshot, then retry the operation. The reserved volume setting of Auto LUN is defined. Release the reserved volume setting of Auto LUN, and then retry the operation. Release the reserved volume setting of Auto LUN, then retry the operation.
Part Code Error Number Error Message Recommended Action 3210 55401 The SSID setting is incorrect. 3210 55402 3210 Severity Level Failure Level Check the specified content, and retry the operation. W 5 There are boundaries that do not have SSID. Check the specified content, and retry the operation. W 5 59001 Are you sure you want to delete the selected V-VOL group? To continue processing, click [OK]. Otherwise, click [Cancel].
Part Code 3305 Error Number 1037 Error Message Recommended Action Severity Level Failure Level The free space remaining in the parity group is not enough to install a customized volume (CV). There is no capacity left in the logical parity group to create CV. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code Error Number Error Message Recommended Action 1102 Volume initialization operation cannot include the last LDEV of RAID striping group. 3305 Severity Level Failure Level Since at least one LDEV is required in the parity group, you cannot uninstall anymore. E 6 1103 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 3305 1104 An error occurred during SVP processing.
Part Code Error Message Recommended Action 1919 The newly added LDEV has not been formatted. Check the blocked LDEV and format the LDEV. 3305 3305 3305 3305 3305 3305 3305 3305 3305 3305 158 Error Number Severity Level Failure Level Check the blocked LDEV and format the LDEV. W 6 2004 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 2005 An error occurred during SVP processing.
Part Code Error Number 3305 3305 3305 3305 3305 3305 3305 3305 Error Message Recommended Action Severity Level Failure Level 2088 The Continuous Access pair is suspended. Add an alternative path. Add an alternative path. W 6 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access. Make sure that there is an alternative path from the MCU. Be sure there is an alternative path from the MCU.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Therefore the specified operation cannot be executed. 3305 2200 The Concurrent Copy or the Compatible XRC operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host. 3305 2201 Processing cannot be performed because of Data Retention Utility settings. Check the settings, then retry the operation.
Part Code Error Number Error Message Recommended Action 2517 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair, or a Compatible FlashCopy pair. Please release the pair definition, then retry the operation. If the hi-Speed Split mode is on, first suspend and then split the pair. Severity Level Failure Level Please release the pair definition, then retry the operation. If the Hi-Speed Split mode is on, first suspend and then split the pair.
Part Code Error Number Error Message Recommended Action 3008 An error occurred during SVP processing. If this problem persists, please call technical support. 3305 Severity Level Failure Level If this problem persists, call technical support. E 2 5013 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 3305 6001 An error occurred during SVP processing.
Part Code 3305 3305 3305 Error Number Error Message Recommended Action 65669 The XP Thin Provisioning volume associated with a pool is included in the items to be maintained. Release the association of the XP Thin Provisioning volume and the pool to be maintained. Severity Level Failure Level Release the association of the XP Thin Provisioning volume and the pool to be maintained.
Part Code Error Message Recommended Action 6023 An error occurred during SVP processing. If this problem persists, please call technical support. 4005 4005 4005 4005 4005 4005 4005 4005 4005 4005 164 Error Number Severity Level Failure Level If this problem persists, call technical support. E 2 6040 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 55246 The total number of Cache Residency Manager areas set for the CLPRs and the maximum number of the Cache Residency Manager areas in the subsystem are not equal. Severity Level Failure Level Check the settings, then retry the operation. E 6 55247 The Cache Residency Manager size set for the CLPR is not a multiple of 512 MB. CLPR No:%s SLPR No:%s Check the settings, then retry the operation.
Part Code Error Number Error Message Recommended Action 55538 Cache Residency Manager cannot be set to the specified volume because the IO Suppression mode is set to Enable. Severity Level Failure Level Disable the IO Suppression mode of this volume, then retry the operation, or remove the volume from the volumes to be set. E 2 55539 Cache Residency Manager cannot be set for this volume because its Cache mode is set to Disable.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 6 4005 58513 Prestaging not completed. Wait a while, refresh the window, then retry the configuration operation. Or check the status of the disk storage system to find whether the storage system is blocked or not. If the problem persists, call technical support. 4005 58514 Currently running microcode version does not support the specified operation. Please call technical support.
Part Code Error Number Error Message Recommended Action 5010 The value specified as the ending address for the data to be placed in cache is smaller than the value specified as the starting address. 4010 4010 Severity Level Failure Level Correct the values specified as the starting and ending addresses, then retry the operation. W 5 5011 The value specified as the Number of Cache Residency Manager areas is equal to or less than one cylinder. Correct the specified content, and retry.
Table 41 Error Codes — Part Code 4105 Part Code Error Number Error Message Recommended Action 4105 1603 This functionality is not available. Cache Residency Manager is required. 4105 6012 4105 Severity Level Failure Level Install the necessary program product. E 6 An error occurred during server processing. If this problem persists, please call technical support. An error occurred during SVP processing. If this problem persists, call technical support.
Part Code Error Number 4105 4105 4105 4105 Error Message Recommended Action 56526 The resources of other SLPR(s) cannot be accessed. Severity Level Failure Level Correct the settings, then retry the operation. E 6 57007 The sum of the maximum values of the PCR capacity per CLPR does not match the maximum value of total PCR capacity. Check the settings, and retry the operation. E 6 57008 The maximum value of PCR capacity per the specified CLPR is not multiples of 512MB.
Part Code Error Number Error Message Recommended Action 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 5105 Severity Level Failure Level If this problem persists, call technical support. E 2 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 7111 An error occurred during SVP processing. If this problem persists, please call technical support. 5105 Severity Level Failure Level If this problem persists, call technical support. E 2 7428 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 5105 8002 The subsystem status is invalid. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue the operation, contact the storage administrator and have the settings across the multiple SLPRs cancelled, then retry the operation. To perform other operations, please select a function button. E 3 5105 56525 Because the settings across the multiple SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator.
Table 44 Error Codes — Part Code 5205 Part Code Error Number Error Message Recommended Action 1076 The specified volume(s) are already used by Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy. 5205 5205 Severity Level Failure Level Check the status of the selected volume. E 6 1077 The specified volume(s) are already used by Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy. Check the status of the selected volume. E 6 1078 The volume is a LUSE volume.
Part Code Error Number Error Message Recommended Action 5205 1117 The volume(s) is already being used by Concurrent Copy. 5205 1118 5205 Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 The volume(s) is already being used by Concurrent Copy. Retry the same operation. If nothing changes, call technical support. E 6 1119 The volume(s) is already being used by Concurrent Copy. Retry the same operation.
Part Code Error Number Error Message Recommended Action 5205 1217 The target volume(s) cannot be used. 5205 1218 5205 Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 The target volume is being formatted. Retry the same operation. If nothing changes, call technical support. E 6 1219 The specified volume(s) are used as a command device. Retry the same operation. If nothing changes, call technical support.
Part Code Error Number Error Message Recommended Action 1232 The specified volume(s) are already used by Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy. 5205 Severity Level Failure Level Check the status of the selected volume. E 6 1233 The specified volume(s) are already used by Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy. Check the status of the selected volume. E 6 5205 1234 The target volume(s) is already being used by Continuous Access.
Part Code Error Number Error Message Recommended Action 5205 1247 The volume is already a source volume. Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 1248 The specified source/target volume is used for a Cross-system Copy volume. Re-execute the same operation. If the problem persists, call technical support. E 6 1249 The specified volume cannot be used because the volume is being used by Cross-system Copy. Select another volume.
Part Code Error Number Error Message Recommended Action 1612 The specified volume has Read Only/Protect/SVOL Disable setting of Data Retention Utility. 5205 Severity Level Failure Level Release the Read Only/Protect/SVOL Disable setting of Data Retention Utility. E 6 2003 An internal process is being executed, or maintenance is in progress. Please try again. Confirm that maintenance operation is not in progress, and retry after a while. E 5 5205 2004 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5205 5203 This functionality is not available because Auto LUN is not installed. 5205 5504 5205 Severity Level Failure Level Please install the required program product. W 6 The volume(s) is already being used by Data Migration. Please release the Data Migration. E 6 5505 The volume(s) is already being used by Continuous Access. Please Release the Continuous Access Pair.
Part Code Error Number Error Message Recommended Action 5205 6531 The SVP is busy. Please wait for a while, and then retry the operation. 5205 6532 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 3 The SVP is now updating the statistics data. Please wait for a while, and then retry the operation. Please retry after a while. If the problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 7411 Failed to write to the plan file (hihsmldv.ini). 5205 Severity Level Failure Level Retry the same operation several times. If the same error occurs, call technical support. E 6 7412 The file contains invalid data. Retry the same operation several times. If the same error occurs, call technical support. E 6 5205 7413 The file (hihsmpin.ini） contains invalid data. Retry the same operation several times.
Part Code 5205 Error Number 7423 Error Message Recommended Action Severity Level Failure Level An internal error occurred. Retry the same operation several times. If the same error occurs, call technical support. E 6 E 6 5205 7424 Failed to delete all plans. Retry the same operation several times. If the same error occurs, call technical support. 5205 7426 Failed to delete plan. Retry the same operation several times. If the same error occurs, call technical support.
Part Code Error Number Error Message Recommended Action 55060 The specified volume migration plan cannot be executed because a volume on which VMA of Data Retention Utility is set is paired with a volume on which VMA is not set. Severity Level Failure Level Please confirm the settings of the specified volumes. W 6 55201 If the migration source volume is a normal volume, a CVS volume of the same capacity as the migration source volume cannot be specified as the migration target volume.
Part Code 5205 5205 5205 5205 5205 5205 5205 5205 Error Number Error Message Recommended Action 55253 The specified source volume is an external volume that does not belong to a Cross-system Copy pair. The specified target volume is an external volume that belongs to a Cross-system Copy pair. Therefore, the specified volumes cannot be used for migration. Severity Level Failure Level Check the source volume setting and the target volume setting.
Part Code Error Number Error Message Recommended Action 55432 The volume(s) are already being used by Compatible FlashCopy or Compatible FlashCopy Version 2. 5205 Severity Level Failure Level Please confirm the setting of the specified volume. E 6 55433 The volume(s) are already being used by Compatible FlashCopy or Compatible FlashCopy Version 2. Please confirm the setting of the specified volume. E 6 5205 55500 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55551 The specified volume is used as a journal volume by Continuous Access Journal or Universal Replicator for Mainframe. 5205 5205 Severity Level Failure Level Please check the setting of the specified volume. E 6 55552 The specified plan is set across an internal volume and an external volume, and the volume is used by Continuous Access Journal or Universal Replicator for Mainframe. Please confirm the setting of the specified volume.
Part Code Error Number Error Message Recommended Action 5205 58451 The storage system is in internal process. Please retry the operation. 5205 65434 5205 5205 Severity Level Failure Level If the problem persists despite retrying, call technical support. W 6 The specified volume(s) are the leaf volume(s) of Business Copy. Please specify another volume. E 6 65673 The specified volume(s) are already being used as of XP Thin Provisioning volume (TP-VOL) (s).
Table 46 Error Codes — Part Code 5305 Part Code Error Number Error Message Recommended Action Severity Level Failure Level Correct the specified contents, and request the setting of the configuration information again. E 6 5305 1064 The specified WWN is already being used. 5305 1258 This port is not properly equipped. Retry the same operation. If nothing changes, call technical support. E 6 5305 2002 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5305 5104 The specified Performance Control group is already registered. 5305 5105 5305 Severity Level Failure Level Check the specified content, and retry. W 6 The target port(s) does not equip the monitored WWN(s). Check the specified content, and retry. W 6 5106 The target WWN is already registered in the port. Check the specified content, and retry. W 6 5305 5107 The specified Name is already used.
Part Code Error Number Error Message Recommended Action 6036 An error occurred during SVP processing. If this problem persists, please call technical support. 5305 Severity Level Failure Level If the same error occurs despite retrying, call technical support. E 2 6050 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 5305 6051 An error occurred during processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 5305 56303 An error occurred during SVP processing. If this problem persists, please call technical support. 5305 56524 This function cannot be used by the storage partition administrator. Select another window. To set this function, contact the storage administrator.
Table 47 Error Codes — Part Code 5307 Part Code Error Number Error Message Recommended Action 5307 5102 The specified Performance Control group is not registered. 5128 The number Performance exceeds the number that registered. Severity Level Failure Level Check the specified content, and retry. W 6 Check the specified content, and retry.
Part Code Error Message Recommended Action Severity Level Failure Level 5111 The number of the WWNs exceeds the maximum number that can be registered on an Performance Control group. Check the specified content, and retry. i 5 5310 5128 The number Performance exceeds the number that registered. Check the specified content, and retry. i 5 5310 5129 The WWN is already registered in another Performance Control group. Check the specified content, and retry.
Part Code Error Number Error Message Recommended Action 5310 9313 The control status will change to WWN Control. 5310 9314 5310 5310 Severity Level Failure Level The control status will change to WWN Control. Please click [OK]. W 5 There is no control, because the upper value is 0 in all ports. Please set up a maximum value to control. W 5 9315 The monitoring switch is turned OFF. If you use the real time option for the first time, turn ON the monitoring switch.
Table 49 Error Codes — Part Code 6005 Part Code Error Number Error Message Recommended Action 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 6005 Severity Level Failure Level If this problem persists, call technical support. E 2 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code 6005 6005 6005 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action Severity Level Failure Level Logical Path between the MCU and the RCU is not active. A logical path does not exist between the MCU and the RCU. Check the path status on RCU Status screen, and reestablish the paths with Edit Path. i 4 8702 The pair status of the M-VOL is not valid. The type of pair status is not permitted for this operation. Refresh and check the screen.
Part Code 6005 6005 Error Number Error Message Recommended Action 8710 The pair status of the specified volume is not valid. 8711 Parameter specified by Continuous Access operation for expansion volume is not valid. Severity Level Failure Level The pair status does not permit this operation. Verify the pair status, and if the operation is permitted retry. i 4 Check the port number, GID, and LUN of the RCU. i 4 The operation was rejected due to a FREEZE state.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 4 6005 8719 Invalid RCU serial number, SSID, Link Address or Controller ID. Check the serial number, SSID, link address and controller ID of the RCU, and set the correct value. Then retry the operation. If the same error occurs, contact technical support. 6005 8720 Too many RCUs. (Four RCUs are the maximum) A maximum of four RCUs are permitted, and that many already exist.
Part Code 6005 Error Number 8731 Error Message Recommended Action Severity Level Failure Level The existing logical addresses are not equal. The logical addresses of all existing paths are not the same. Delete the RCU, then re-add it, using the same logical address as other existing paths. i 4 E 4 6005 8732 Too many SSIDs (Only Four SSIDs are allowed). The maximum number of SSIDs (four) has been entered. Verify that the SSIDs are valid, delete one or more, then retry the operation.
Part Code Error Number 6005 8743 6005 6005 6005 6005 Error Message Recommended Action Pinned track(s) exists on the R-VOL. 8744 8745 8746 8747 Severity Level Failure Level Check the status of the R-VOL tracks, and clear the pinned tracks. W 4 The specified M-VOL condition is not valid for Continuous Access. The M-VOL is not available for the requested operation, because of one or more of the following reasons: 1. The volume is blocked. 2. The volume is under maintenance. 3.
Part Code Error Number Error Message Recommended Action Specified M-VOL may be in use by HOST. 8749 6005 Severity Level Failure Level Data migration cannot start because the volume is online. Please vary the path offline and retry. i 4 Specified R-VOL is still online from HOST. Please check if the input number of R-VOL is correct. If not, enter the correct R-VOL number. If the number is correct, vary the specified path offline.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level R-VOL Device Cache status is not active. Check the device cache status of R-VOL from host. If it is off, set it on and retry. If it cannot be set on, call technical support. i 4 R-VOL DFW status is not active. Check the DFW status of the R-VOL from the host. If it is off, set it on and retry. If it cannot be set on, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 4 6005 8772 Change pair operation failed due to communication error or the R-VOL status is invalid. The pair option change operation failed, either because a communication error occurred or because the R-VOL status is not valid. Please verify the status. Also view the License Key window at the RCU side and check the licensed capacity for Volume Retention Manager.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The Continuous Access option must be installed in the MCU and RCU before a Continuous Access volume pair can be created. i 4 6005 8781 TrueCopy for Mainframe function is not installed in the specified controller. 6005 8785 The M-VOL is defined as the expansion volume. Please recheck the volume. i 4 6005 8786 The R-VOL is defined as the expansion volume. Please recheck the volume.
Part Code Error Number Error Message Recommended Action 8795 The operation failed because the specified M-VOL was one of the following: • A T-VOL of ShadowImage for Mainframe and not in the Split pair(PSUS) status. • An S-VOL of Business Copy and not in the Split pair (PSUS) status. • A reserved volume of ShadowImage for Mainframe or Business Copy. • A volume in the Reverse Copy status of ShadowImage for Mainframe or Business Copy. • A T-VOL of Compatible FlashCopy.
Part Code Error Number 6005 6005 6005 6005 6005 6005 6005 6005 Error Message Recommended Action 8800 The R-VOL is already in use for Auto LUN. 8801 8802 8803 8804 8805 8806 8807 Severity Level Failure Level Verify the status of the specified R-VOL. E 4 The R-VOL is reserved, or the RCU or the path between MCU-RCU is in a heavy load condition. Verify the status of the specified R-VOL. If the device is not reserved, retry the operation. i 4 CT group is not active.
Part Code 6005 Error Number 8808 Error Message Recommended Action Severity Level Failure Level Please retry Add Pair (Paircreate)/Resume Pair (Pairresync) operation in a few minutes. The add/resume pair operation failed, because the either the specified volume or another volume in the same group is being changed to simplex or suspend status. Retry the operation after the status change is completed. i 4 Add/resume pair operation failed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 4 • it is a reserved volume of Business Copy or ShadowImage for Mainframe. • it is a volume reserved by Auto LUN. • it is used by Universal Replicator for Mainframe. 6005 8820 The specified R-VOL is not a permissible condition of Continuous Access. The Continuous Access operation failed, because R-VOL has one of the following conditions: 1. The volume is blocked. 2. The volume is under maintenance. 3.
Part Code Error Number Error Message Recommended Action 6005 8830 The specified M-VOL is already used as a reserved volume of Auto LUN. 6005 8831 Severity Level Failure Level Check the status of the specified M-VOL (P-VOL) from HOST or SVP. i 4 The specified R-VOL is already used as a reserved volume of Auto LUN. Check the status of the specified R-VOL (S-VOL) from HOST or SVP. i 4 8832 Please wait a few minutes and retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation.
Part Code 6005 Error Number 8843 Error Message Recommended Action Severity Level Failure Level Suspend(Pairsplit-r) operation failed because specified volume or other volume in the same group is not in permissible status. The operation failed, because of one of the following reasons: 1. The specified volume is simplex. 2. There is no duplex or duplex-pending volume in the group. 3. Either the specified volume or another volume in the same group is suspended. Verify the status, and retry the operation.
Part Code Error Number 6005 8852 6005 6005 6005 6005 212 Error Message Recommended Action Severity Level Failure Level R-VOL status change failed after M-VOL status change. Confirm R-VOL status. Confirm the R-VOL status. E 4 Delete Pair (Pairsplit-S) operation failed because M-VOL is in Simplex (SMPL) status. The operation failed, because of one of the following reasons: 1. The specified volume is simplex. 2. There is no duplex, duplex-pending, or suspend volume in the group.
Part Code Error Number Error Message Recommended Action 8858 6005 Severity Level Failure Level All volumes were not deleted by the Delete Pair (Pairsplit-S) operation. The operation failed for all of the volumes, because either the pair status of the volume is SEQCHK or the consistency time of the volume does not match the consistency time of the CT group. Verify the status of the failed volumes. If necessary, retry the Delete Pair operation with the volume or the group option.
Part Code Error Number Error Message Recommended Action 8870 CT Group Option cannot be changed unless all asynchronous pairs in the group are suspended or deleted. 6005 Severity Level Failure Level The group operation failed because the specified group has at least one asynchronous pair. Renew and check the Continuous Access screen. i 4 8871 The TrueCopy Asynchronous for Mainframe function is not installed in the specified MCU.
Part Code Error Number Error Message Recommended Action 6005 8888 An internal error occurred. 6005 8889 6005 Severity Level Failure Level Please call technical support. E 4 The specified port is not equipped. Refresh the screen, and retry. If nothing changes, call technical support. E 4 8890 The specified port is being initialized. Please wait until the initialization of the port ends, and retry the operation. E 4 6005 8891 Logical paths exist on the MCU port.
Part Code 6005 6005 6005 Error Number 8904 8905 8906 Error Message Recommended Action Severity Level Failure Level No more space is left in MCU for differential management. If the extended shared memory (SM #2) is not installed in MCU, install the shared memory to MCU according to the installation instruction of the extended shared memory for remote copy (Shared Memory Size Configuration dialog box), then create a pair.
Part Code 6005 Error Number 8911 Error Message Recommended Action Severity Level Failure Level Logical paths exist on the port. The Remote Console computer detected a logical path (z/OS) on the port. Please delete the path(s) and retry the operation. i 4 i 4 6005 8912 Logical paths exist on the port. The Remote Console computer detected a logical path (z/OS) on the port. Please delete the path(s) and retry the operation. 6005 8913 Invalid port type.
Part Code Error Number Error Message Recommended Action 6005 8926 The specified R-VOL is prohibited to use by Volume Security. 6005 8927 6005 Severity Level Failure Level Confirm the status of Volume Security of the specified R-VOL. E 4 The specified M-VOL is prohibited to use by Volume Security. Confirm the status of Volume Security of the specified M-VOL. E 4 8929 Invalid port type. Please check the port status and retry. W 4 6005 8930 Logical paths exist on the RCU port.
Part Code Error Number Error Message Recommended Action 8943 The specified volume or other volume(s) of the same group in the RCU is being changed to Simplex/Suspend status. Retry the operation a few minutes later. 8944 Severity Level Failure Level Refresh the window a few minutes later and check the status of the specified volume and other volume(s) of the same group in the RCU. If it is possible to perform operations on the volume(s), retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8977 A pair cannot be created, because the specified R-VOL is an external volume. Check the status of the specified R-VOL. i 4 6005 8980 The operation failed because the licensed capacity of Volume Retention Manager on the RCU side was exceeded. Confirm the licensed capacity Volume Retention Manager on the RCU side. To execute this operation, purchase a license key that allows you to use a larger capacity.
Part Code Error Number Error Message Recommended Action 6005 56524 This function cannot be used by the storage partition administrator. Severity Level Failure Level Select another window. To set this function, contact the storage administrator. E 3 57005 An error occurred during SVP processing. If this problem persists, please call technical support. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level A pair cannot be created because the licensed capacity of Data Retention Utility on the RCU side is insufficient or Data Retention Utility is not installed on the RCU. Check the licensed capacity of Data Retention Utility on the RCU side or confirm whether Data Retention Utility is installed on the RCU.
Part Code 6005 6005 6005 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action Severity Level Failure Level 58498 A pair cannot be created because the specified M-VOL is being used as a pool volume. Please specify another volume. i 5 58499 A pair cannot be created because the specified R-VOL is being used as a pool volume. Please specify another volume. i 5 58509 A communication time-out error occurred between MCU and RCU.
Part Code 6005 6005 6005 224 Error Number Error Message Recommended Action 58713 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the RCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code 6005 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action 68011 A pair cannot be created because the specified M-VOL is being used as an XP Thin Provisioning volume. Severity Level Failure Level Check whether the specified R-VOL is an XP Thin Provisioning volume. W 0 68012 A pair cannot be created because the specified R-VOL is being used as an XP Thin Provisioning volume. Check whether the specified R-VOL is an XP Thin Provisioning volume.
Part Code Error Number Error Message Recommended Action 6007 6022 The SVP is busy. Please wait for a while, and then retry the operation. 6007 6023 6007 6007 6007 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 3 The SVP is busy. Please wait for a while, and then retry the operation. If the same problem persists despite retrying, call technical support. E 3 6024 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5035 There are no CT groups for the asynchronous Continuous Access. Please try again after registering CT groups. Severity Level Failure Level Register a CT group, and retry. W 5 5066 The RCU and one of the CT group channel types do not match. Please correct RCU or CT group. Select the same path type for RCU and CT group. W 5 6010 5131 The combination of parameters which you specified is not permitted.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 8101 The system cannot apply the new configuration. Do you want to refresh? Click [Refresh], and retry. W 5 6010 8928 An error occurred when copying started. Please suspend the specified pair, and perform the operation to resume the pair. W 0 6010 9006 Exchange the channel cable connections after confirmation of the port type. Please follow the instructions in the message.
Part Code Error Number Error Message Recommended Action 6010 9071 Are you sure you want to delete the paths of a specified RCU? 6010 9072 6010 Severity Level Failure Level To delete the specified path, click [OK]. Otherwise, click [Cancel]. i 0 Are you sure you want to delete the specified volume pairs? To delete the specified pair, click [OK]. Otherwise, click [Cancel]. i 0 9073 Are you sure you want to suspend the specified volume pairs? To suspend the specified pair, click [OK].
Part Code Error Number Error Message Recommended Action 6010 9114 The value has been changed. Do you want to continue the operation? 6010 9115 6010 Severity Level Failure Level To continue the process, click [OK]. Otherwise, click [Cancel]. i 0 The monitoring was stopped by another operator. The graph will be closed. Click [OK]. i 0 9116 Another operator has changed the Gathering Interval value. The graph will be closed. Click [OK].
Part Code Error Number Error Message Recommended Action 9154 As a result of this operation, you will not be able to re-start ERASE R-VOL operation. To delete the pair forcibly, please try again with Force option. Severity Level Failure Level Please follow the instructions in the message. W 0 9155 The history file has been updated. Select the OK button to display the history logs from the beginning. Click [OK].
Part Code Error Number Error Message Recommended Action 9308 You set the same path more than once. The duplicate paths are excluded. Severity Level Failure Level Since there were overlapped paths in the added paths, the overlapped paths were eliminated. Click [OK] and continue. W 0 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added.
Part Code Error Number Error Message Recommended Action 9360 The specified value exceeds the range. Alternatively, the relationship between the specified values is not appropriate. Severity Level Failure Level Check the specified values and retry the operation. W 5 55035 If you plan to create a pair with the specified LUSE volumes, a DKC path is required. Select Add RCU command, then register a DKC path.
Part Code 6010 Error Number 59030 Error Message Recommended Action Severity Level Failure Level The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The monitoring data currently saved will be deleted if you change the setting of the monitoring switch. If necessary, use the Performance Monitor Export Tool to export the monitoring data file. i 5 To continue processing, click [OK]. To stop processing, click [Cancel].
Table 53 Error Codes — Part Code 6505 Part Code Error Number Error Message Recommended Action 3003 An error occurred during SVP processing. If this problem persists, please call technical support. 6505 Severity Level Failure Level If the problem persists despite retrying, call technical support. E 2 5013 An error occurred during SVP processing. If this problem persists, please call technical support. Retry the operation. If this problem persists, call technical support.
Part Code 6505 6505 6505 Error Number Error Message Recommended Action 8001 A communication time-out error occurred in the subsystem. Please wait for a while, and then retry the operation. Severity Level Failure Level Please wait a while, then retry the operation. E 3 8002 A communication time-out error occurred in the subsystem. Please wait for a while, and then retry the operation. Please wait a while, then retry the operation. E 3 8100 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please refresh the window and check the pair status of the pair. If the pair status can be manipulated, retry the operation. W 0 6505 8710 The pair status of the specified data volume is incorrect. 6505 8711 The specified parameter is incorrect. Check the port number, ID, and LUN of the storage system. i 4 E 4 6505 8712 The operation was rejected due to a FREEZE state.
Part Code 6505 6505 6505 Error Number Error Message Recommended Action 8723 The Edit Path operation was rejected because the specified path is the last path of some Continuous Access pairs. 8724 8727 Severity Level Failure Level Add another path, or delete all pairs on the remote storage system. Then retry the operation. i 4 The specified number of paths is less than the minimum number specified in the DKC Option window. Check the number of paths.
Part Code 6505 6505 6505 Error Number 8733 8734 8735 Error Message Recommended Action Severity Level Failure Level Continuous Access Journal or Universal Replicator for Mainframe is not installed in the subsystem. Continuous Access Journal or Universal Replicator for Mainframe must be installed in the storage system when you create a path or a pair for Continuous Access Journal or Universal Replicator for Mainframe.
Part Code 6505 6505 6505 6505 240 Error Number 8744 8745 8746 8749 Error Message Recommended Action Severity Level Failure Level The specified primary data volume cannot be used. Check whether the primary data volume is in any of the following conditions: • Data in the primary data volume is being copied; correction copy or drive copy is in progress. • The primary data volume is in correction access condition. • The primary data volume is blocked.
Part Code Error Number Error Message Recommended Action 6505 8753 An internal error occurred. 6505 6505 Severity Level Failure Level Please check the SSB log, then call technical support. E 4 8757 One side of the cache is blocked in the primary subsystem. Check the status of the cache in the primary storage system. Ensure that the cache is not blocked, then retry the operation. W 4 8758 An unexpected error occurred in the primary subsystem. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level • The volume was a ShadowImage for Mainframe T-VOL in non-Split status. • The volume was a reserved volume. • The volume was in the Reverse Copy status. 8796 The operation failed because the specified secondary data volume was one of the following: • An S-VOL or reserved volume of Business Copy. • A T-VOL or reserved volume of ShadowImage for Mainframe. • A T-VOL of Compatible FlashCopy.
Part Code 6505 Error Number 8830 Error Message Recommended Action Severity Level Failure Level The specified primary data volume is already reserved by Auto LUN. Volumes reserved by Auto LUN cannot be specified as primary data volumes. Check the status of the specified primary data volume from the host or the SVP. i 4 i 4 6505 8831 The specified secondary data volume is already reserved by Auto LUN. Volumes reserved by Auto LUN cannot be specified as secondary data volumes.
Part Code Error Number Error Message Recommended Action 6505 8896 Parameter error has occurred. 6505 8897 6505 Severity Level Failure Level Refresh the window and retry. If nothing changes, call technical support. E 4 LUs exist on the port. Please delete the LUs defined on the port and retry the operation. E 4 8898 Pending data exists on the port. Retry the operation. i 4 6505 8899 An internal error occurred. Please check the SSB log, then call technical support.
Part Code Error Number Error Message Recommended Action 8934 The Add Pair (Paircreate) operation failed because the specified secondary data volume was a NAS system volume. Severity Level Failure Level Check the configuration of the specified secondary data volume. W 0 8936 The Paircreate (Add Pair) operation failed. The microcode version of the specified secondary subsystem does not support Continuous Access with NAS volumes. Please check the microcode version of the secondary storage system.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58007 Invalid parameter (journal group number). Check the specified journal group number. i 0 6505 58008 The command was rejected by the subsystem because the command is unknown. Please call technical support. i 0 6505 58009 No more remote subsystems can be registered. Reduce the number of registered remote storage systems, then retry the operation.
Part Code Error Number Error Message Recommended Action 6505 58025 The specified cache value for restore journal groups is invalid. 6505 58026 Severity Level Failure Level Check the specified cache value for restore journal groups. i 0 The specified threshold for ending creation of asynchronous journal is invalid. Check the threshold for ending creation of asynchronous journal. i 0 58027 The specified threshold for ending creation of synchronous journal is invalid.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58038 No more path group IDs can be registered. Check the number of registered path group IDs. i 0 6505 58039 The specified volume is already used as a journal volume or a data volume. Specify another volume. i 0 6505 58040 An internal error occurred. Please check the SSB log, then call technical support. E 4 6505 58064 Too many requests.
Part Code Error Number Error Message Recommended Action 58079 The specified primary data volume cannot be used as an S-VOL (secondary volume) because of Volume Retention Manager settings or Data Retention Utility settings. Severity Level Failure Level Check the status of the specified primary data volume in the Volume Retention Manager window or the Data Retention Utility window. i 0 58080 A Concurrent Copy operation is in progress on the specified primary data volume.
Part Code Error Number Error Message Recommended Action 58089 No more remote subsystems can be registered. 6505 Severity Level Failure Level Reduce the number of registered remote storage systems, then retry the operation. i 0 58090 The SLPR number of the specified data volume does not match the SLPR number of the journal volume in the specified journal group. Check the SLPR number of the specified data volume and the journal volume in the journal group.
Part Code Error Number Error Message Recommended Action 58103 The specified secondary data volume is a reserve volume of a mainframe host. 58104 Severity Level Failure Level Check the status of the specified secondary data volume from the mainframe host. i 4 The specified secondary data volume is already used by Compatible XRC. Check the status of the specified secondary data volume from the mainframe host.
Part Code Error Number Error Message Severity Level Failure Level 58271 The specified secondary data volume cannot be used because of the following reasons: • S-VOL Disable is set by Data Retention Utility. • The VMA setting differs between the primary data volume and the secondary data volume. • Protection is set by Volume Retention Manager. Please check the following items on the Data Retention Utility window if the specified secondary data volume is an open-system volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the emulation type of the specified secondary data volume or the restore journal volume. i 0 6505 58279 The emulation type of the specified secondary data volume and the restore journal volume is incorrect due to one of the following reasons: • The emulation type is not supported. • The combination of emulation types within the journal group is incorrect.
Part Code Error Number Error Message Recommended Action 6505 58288 The specified primary data volume is already paired with another volume. 6505 58289 6505 6505 Severity Level Failure Level Check the status of the specified primary data volume. i 0 The specified secondary data volume is already paired with another volume. Check the status of the specified secondary data volume. i 0 58290 The specified primary data volume is not paired with any another volume.
Part Code 6505 Error Number 58297 Error Message Recommended Action Severity Level Failure Level The specified primary data volume is being used by another program product.
Part Code Error Number Error Message Recommended Action The Add Pair (Paircreate) operation failed because the specified primary data volume was a P-VOL for Continuous Access or an M-VOL for TrueCopy for Mainframe. Severity Level Failure Level Please specify another primary data volume, and retry the operation. W 0 58325 The specified primary data volume is used by Continuous Access or TrueCopy for Mainframe.
Part Code Error Message Recommended Action Severity Level Failure Level 58334 Because the status of the specified journal group is neither Initial nor Stop, the parameter related to the inflow cannot be changed. Please check the status of the specified journal group. i 0 58335 Because the specified journal group is not in Initial status, the timer type cannot be changed. Please check the status of the specified journal group.
Part Code 6505 6505 6505 6505 6505 6505 6505 258 Error Number Error Message Recommended Action 58344 The Add Pair (Paircreate) operation failed because the specified secondary data volume is a LUSE volume. Severity Level Failure Level Please check the specified secondary data volume and specify a non-LUSE volume. W 0 58345 The Add Pair (Paircreate) operation failed due to one of the following reasons: • The IO suppression mode of the specified secondary data volume is enabled.
Part Code 6505 6505 6505 Error Number Error Message Recommended Action The Add Pair (Paircreate) operation failed because the specified secondary data volume was one of the following: • An S-VOL of Business Copy. • A T-VOL of ShadowImage for Mainframe or Compatible FlashCopy. • A reserved volume of Business Copy or ShadowImage for Mainframe. • A P-VOL of Business Copy in Swap or Reverse Copy status. • An S-VOL of ShadowImage for Mainframe in Swap or Reverse Copy status.
Part Code Error Number 6505 6505 6505 6505 6505 6505 6505 6505 6505 260 Error Message Recommended Action 58451 The storage system is in internal process. Please retry the operation. Severity Level Failure Level If the problem persists despite retrying, call technical support. W 0 58455 The Add Pair operation or the Resume Pair operation failed because the specified primary data volume was a T-VOL of Compatible FlashCopy.
Part Code 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action Severity Level Failure Level 58490 Only the pair option of the primary data volume was updated. Failed to update the pair option of the secondary data volume. A communication error between the primary and the secondary storage systems occurred, or the microcode of the secondary storage system does not support the change pair option function.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the mirror ID assigned to the specified primary data volume number (LDKC:CU:LDEV) from the secondary storage system, and assign a mirror ID that is not used, and retry the operation. W 0 6505 58510 The Add Pair (Paircreate) operation failed. The combination of the specified primary data volume number (LDKC:CU:LDEV) and the mirror ID is the same as the combination specified from another primary subsystem.
Part Code 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58561 The Add Pair operation or the Resume Pair operation failed because the timer type of the master journal group was different from the timer type of the restore journal group. Severity Level Failure Level Please check the timer type of the master journal group and the restore journal group. W 0 58562 The specified volumes or the volumes in the specified journal group were deleted.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 264 Error Number Error Message Recommended Action 58591 The Add Pair (Paircreate) operation or the Resume Pair (Pairresync) operation failed because the journal volumes of the specified restore journal group were blocked. Severity Level Failure Level Check the status of the journal volumes of the specified restore journal group. W 0 58592 The specified operation failed because the subsystem was being powered on or powered off.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58601 Journal groups cannot be added to the extended consistency group (EXCTG), because the additional shared memory was not installed. Severity Level Failure Level Please call technical support and install additional shared memory. W 0 58602 Journal groups cannot be added to the extended consistency group (EXCTG), because the number of subsystems in the EXCTG exceeds the maximum.
Part Code Error Message Recommended Action 58611 The specified operation failed because the microcode exchange was in progress on the subsystem in the extended consistency group (EXCTG). 6505 6505 6505 6505 6505 6505 6505 6505 6505 6505 266 Error Number Severity Level Failure Level Retry the operation after the microcode exchange completes. W 0 58612 The previously executed update processing of the extended consistency group (EXCTG) has not completed.
Part Code Error Number Error Message Recommended Action 58624 Journal groups cannot be added to the extended consistency group (EXCTG), because the combination of the serial number and the command device is invalid. Severity Level Failure Level Check whether the specified command device of the specified serial number exists. W 0 58625 Journal groups cannot be added to the extended consistency group (EXCTG), because the specified journal groups are being used by another program product.
Part Code Error Number Error Message Recommended Action Delta resync failed. The specified primary data volume should meet the following requirements. • The specified volume is a secondary data volume for Continuous Access Synchronous or TrueCopy for Mainframe Synchronous. • The pair status of Continuous Access Synchronous or TrueCopy for Mainframe Synchronous is PAIR or Duplex. the Continuous Access window or the TrueCopy for Mainframe window.
Part Code 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58690 The recovery to the status ready for Delta resync failed, because the status of the specified primary data volume was one of the following: • The primary data volume is being copied; correction copy or drive copy is in progress. • The primary data volume is in correction access status. • The primary data volume is blocked • The primary data volume is being maintained.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 270 Error Number Error Message Recommended Action 58696 The specified volume cannot be used as a journal volume because the volume is an external volume to which the I/O suppression mode is enabled. Severity Level Failure Level Check the I/O suppression mode of the specified volume. W 0 58697 The journal volume cannot be deleted from the specified journal group because of the mirror status.
Part Code 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58704 The Add Pair (Paircreate) operation to get ready for Delta resync failed because the status of the volumes was one of the following: • The P-VOL for Continuous Access Synchronous and the primary data volume for Continuous Access Journal are different. • The M-VOL for TrueCopy for Mainframe Synchronous and the primary data volume for Universal Replicator for Mainframe are different.
Part Code 6505 6505 6505 272 Error Number Error Message Recommended Action 58717 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the RCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58720 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the MCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code Error Number Error Message Recommended Action 68007 The Add Pair (Paircreate) operation failed. The LDKC number of the specified secondary data volume is different from the LDKC number of the specified restore journal group. Severity Level Failure Level Confirm that the LDKC number of the secondary data volume and the LDKC number of the restore journal group is the same.
Part Code 6505 6505 6505 6505 Error Number Error Message Recommended Action 68019 The secondary subsystem does not support the LDEV number of the specified primary data volume. Severity Level Failure Level Check whether the secondary subsystem supports the LDEV number of the specified primary data volume. W 0 68024 The Add Pair(Paircreate) operation failed because the current microcode version does not support Delta Resync. Check the microcode version of the connected storage system.
Table 55 Error Codes — Part Code 6510 Part Code Error Number Error Message Recommended Action 6510 5030 The displayed information has not been changed. 6510 5137 6510 Severity Level Failure Level Specify the data that you want to register in the SVP. Then retry the operation. W 0 The Operation value is invalid. Specify the correct value. Check the contents, and retry. W 0 5138 The value specified for Gathering Interval is invalid. Specify a valid value within the range of 1 to 15.
Part Code Error Number Error Message Recommended Action 9024 Are you sure you want to exchange the specified ports? Please confirm the associated channel paths are off-line. Severity Level Failure Level Please ensure that the associated channel paths are offline. W 5 9025 Are you sure you want to switch the ports? If the remote copy paths exist on the ports, delete them beforehand. Please remove remote copy paths associated with the ports.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. i 0 6510 9116 Another operator has changed the Gathering Interval value. The graph will be closed. 6510 9117 Are you sure you want to close the graph? To close the graph, click [OK]. If not click [Cancel]. i 0 6510 9118 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel]. i 0 6510 9119 No graph item has been selected.
Part Code Error Message Recommended Action 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added. 6510 6510 6510 6510 Error Number Severity Level Failure Level Since all the added paths are redundant, the paths cannot be added. Click [OK] and continue. W 0 9327 The monitoring time is over, but the history file is not fully updated yet. Click [Refresh] to update the history file.
Part Code Error Number Error Message Recommended Action 56504 No journal group with the same CLPR number as the specified volume is registered. Please register a journal group that has the same CLPR number as the specified volume, and then retry the operation. Severity Level Failure Level Please register a journal group that has the same CLPR number as the specified volume, then retry the operation. i 0 56505 There are no secondary subsystems available.
Part Code Error Number 6510 59026 6510 6510 6510 6510 6510 6510 6510 Error Message Recommended Action Severity Level Failure Level The same DKC is specified more than once. Check the DKC setting. Check the DKC setting. W 0 The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The current monitoring data will be deleted if you change the setting of the monitoring switch.
Part Code 6510 6510 6510 6510 6510 Error Number Error Message Recommended Action The specified parity group does not contain volumes that can be registered or deleted as journal volumes. 59108 Severity Level Failure Level Please specify another parity group. W 0 The master journal group number for the specified data volume exceeds 0x0F. Please check the master journal group number for the specified data volume.
Part Code Error Number Error Message Recommended Action 59153 The journal volume cannot be deleted because the status of the mirror of the journal group is Active. Severity Level Failure Level Change the status of the mirror of the journal group to Stop or Initial, then retry the operation. W 0 59323 The entered parameter is invalid. The serial number, the controller ID or the journal group to be added is not specified. Check the entered parameter.
Part Code Error Message Recommended Action Severity Level Failure Level 65664 The specified volume is not valid for this program product. Specify another volume. Specify another volume. W 0 6510 65665 The specified volume is not the volume to be monitored. Check the monitoring setting. Check the monitoring setting. W 0 6510 69016 Are you sure you want to cancel the export? To stop the operation, click [OK]. To continue the operation, click [Cancel].
Part Code Error Number Error Message Recommended Action 6610 5140 The specified CU number is incorrect. Specify the correct CU number. 6610 5141 6610 Severity Level Failure Level Specify the correct CU number. W 0 The specified LDEV number is incorrect. Specify the correct LDEV number. Specify the correct device number. W 0 5144 Some of the entered values are incorrect. Check the values and then specify correct values. Check the values, then specify correct values.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue to change ports, click [OK]. W 5 6610 9026 Are you sure you want to switch the ports? If any remote copy paths exist on the ports, delete them beforehand. Also, to avoid the switching operation from being reported as a failure, confirm first that a message prompting you to change the channel cable connections is displayed, and then perform the necessary changes.
Part Code Error Number Error Message Recommended Action 6610 9117 Are you sure you want to close the graph? 6610 9118 6610 Severity Level Failure Level To close the graph, click [OK]. Otherwise, click [Cancel]. i 0 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel]. i 0 9119 No graph item has been selected. Please select a graph item. Select a graph item. i 0 9120 The graph will be closed if you execute the processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [Refresh] to update the history file. If this problem persists, call technical support. i 0 6610 9327 The monitoring time is over, but the history file is not fully updated yet. 6610 9332 This operation is not applied yet. Click [OK], then continue the operation. i 0 55036 Too many data volumes in the journal group. Check the number of data volumes in the journal group.
Part Code Error Number Error Message Recommended Action 56504 No journal group with the same CLPR number as the specified volume is registered. Please register a journal group that has the same CLPR number as the specified volume, and then retry the operation. Severity Level Failure Level Please register a journal group that has the same CLPR number as the specified volume, then retry the operation. i 0 56505 There are no secondary subsystems available.
Part Code Error Number 6610 59026 6610 6610 6610 6610 290 Error Message Recommended Action Severity Level Failure Level The same DKC is specified more than once. Check the DKC setting. Check the DKC setting. W 0 The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The current monitoring data will be deleted if you change the setting of the monitoring switch.
Part Code Error Number Error Message Recommended Action 59042 Severity Level Failure Level There are no valid journal groups. All journal groups are used by Universal Replicator for Mainframe or Continuous Access Journal. If possible, delete journal groups of Universal Replicator for Mainframe or Continuous Access Journal, then start the Continuous Access Journal window or the Universal Replicator for Mainframe window.
Part Code 6610 6610 Error Number Error Message Recommended Action 59112 The CLPR number of the specified data volume is different from the CLPR number of the data volume in the Preview list. In this operation, please specify only one CLPR number. 59113 Severity Level Failure Level Please specify only the volume that has the same CLPR number as the CLPR number of the volume in the Preview list.
Part Code Error Number Error Message Recommended Action 59153 The journal volume cannot be deleted because the status of the mirror of the journal group is Active. 6610 6610 Severity Level Failure Level Change the status of the mirror of the journal group to Stop or Initial, then retry the operation. W 0 59321 No more journal groups can be added to the specified extended consistency group (EXCTG). Check the number of journal groups in the specified extended consistency group (EXCTG).
Part Code Error Number Error Message Recommended Action 59330 The local DKC cannot be specified for the extended consistency group (EXCTG), because the serial number other than the local DKC is entered. Delete the entered DKC to use the journal group of the local DKC. Severity Level Failure Level Delete the entered DKC to use the journal group of the local DKC. W 0 59332 A multiplatform volume is included in the specified volumes.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Error Message Recommended Action Severity Level Failure Level because the number of EXCTG exceeds the maximum. Table 58 Error Codes — Part Code 6805 Part Code Error Number 6805 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If the same problem persists despite retrying, call technical support. E 2 6805 6012 An error occurred during SVP processing.
Part Code Error Number 6805 55209 6805 6805 6805 6805 6805 6805 Error Message Recommended Action The maximum number of CLPRs that can be created was exceeded. 55210 Severity Level Failure Level Please specify the number of CLPRs within the valid range. E 3 The Block Option setting is incorrect. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. W 5 55211 The Donot Block (Volume Level) option setting is incorrect.
Part Code 6805 Error Number 55220 Error Message Recommended Action Severity Level Failure Level The SLPR number is duplicated. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. W 5 W 5 E 3 Severity Level Failure Level 6805 55221 The CLPR number is duplicated. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support.
Part Code 6810 6810 6810 Error Number Error Message Recommended Action 55219 Severity Level Failure Level The Sleep Time setting is incorrect. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. i 0 59046 This function will apply the setting to all the target CLPRs. This function will overwrite the setting on a CLPR if the setting is already applied to the CLPR.
Part Code Error Number Error Message Recommended Action 7005 6023 The SVP is busy. Please wait for a while, and then retry the operation. 7005 6502 7005 7005 7005 7005 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 3 Processing in progress. Please wait for a while, and then retry the operation. Wait a while, and retry the operation. i 0 6503 The target volume status is being changed to SMPL. Wait a while, and retry the operation.
Part Code Error Number Error Message Recommended Action 8506 The command was rejected. The specified S-VOL is being used from the host or by a Continuous Access volume. Severity Level Failure Level Change the specified S-VOL to other volume, or stop using the S-VOL in the host or Continuous Access, then retry the operation. i 0 8507 The Pairsplit command was issued to the pairs in a PSUS status. You cannot execute the Pairsplit command because the pair is already in the PSUS status.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the volume capacity. i 0 7005 8519 You cannot set a pair because the number of cylinders is different for each. Make sure that the capacity is the same for both. 7005 8520 You cannot set a pair, because the volume type is different for each. Specify the volume of the same emulation type, and retry the operation. i 0 7005 8521 The number of multiple copy jobs exceeded the maximum.
Part Code Error Message Recommended Action Severity Level Failure Level 8540 There is sufficient shared memory to create 4096 pairs, but initial subsystem setup is required before creating pairs. Please call technical support. i 0 7005 8541 There is sufficient shared memory to create 4096 pairs, and the initial subsystem setup is complete. Close the message box. i 0 7005 8542 Failed to complete the initial shared memory setup. Please call technical support.
Part Code Error Number Error Message Recommended Action 7005 8557 The volume is not implemented. 7005 8558 7005 Severity Level Failure Level You cannot execute the operation for the volume which is not implemented. i 0 The volume cannot be used. Please call technical support, and check if the volume status is normal. i 0 8559 The volume is being formatted. Wait until the volume is formatted, and retry the operation.
Part Code Error Number Error Message Recommended Action 7005 8577 The number of reserved volumes to be defined exceeds the maximum. 7005 Severity Level Failure Level Stop the operation of the Reserve volume setting, or delete the Reserve volume. i 0 8578 The P-VOL is already paired with a backup volume. The P-VOL cannot be paired with the target volume. Check the contents, and retry. i 0 7005 8579 No volume is defined as a reserved volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8595 The specified P-VOL does not exist. Refresh, then retry the operation. i 0 7005 8596 The specified volume is a reserved volume. Release the Reserve attribute of the specified volume. i 0 7005 8597 No more pairs can be created for the specified P-VOL. You cannot create pairs for the P-VOL anymore. Delete the existing pairs. i 0 7005 8598 The specified volume is not a P-VOL.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8614 The S-VOL is used as a Continuous Access P-VOL. Delete the Continuous Access pair. i 0 7005 8615 The S-VOL is used as a Continuous Access S-VOL. Delete the Continuous Access pair. i 0 7005 8618 The S-VOL is already defined as a P-VOL. Check the volume number. i 0 7005 8619 The specified S-VOL is defined as a source volume for Auto LUN. Release the Auto LUN setting.
Part Code Error Number Error Message Recommended Action 7005 8635 The specified P-VOL is defined as a reserved volume for Auto LUN. 7005 8636 7005 Severity Level Failure Level Specify other volume(s), or release the Auto LUN Setting. i 0 The specified S-VOL is defined as a reserved volume for Auto LUN. Specify other volume(s), or release the Auto LUN Setting. i 0 8637 The specified P-VOL is used as a source volume for Auto LUN. Specify other volume(s), or release the Auto LUN Setting.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8648 The boot device and the P-VOL do not match in the Paircreate command. Check the specified volume number. i 0 8649 Because the boot device is the S-VOL in the Pairsplit-S command, the flag does not match. Check the specified volume number. i 0 7005 8650 The boot device and the P-VOL do not match in the Paircreate, Pairresync, or Pairsplit-S command. Check the target volume number.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The command was rejected, because you tried to create a volume pair formed with a volume to which VMA is set by Data Retention Utility and a volume without VMA. You cannot create a pair using these volumes. To create a pair by using a volume without VMA, you must only use volumes without VMA. To create a pair by using a volume with VMA, you must only use volumes with VMA.
Part Code Error Number Error Message Recommended Action 58002 The Quick Restore command has been rejected because the specified pair is composed of a normal volume and a customized volume (CV). Severity Level Failure Level The quick restore operation cannot be performed when the pair is composed of a normal volume and a customized volume (CV). Select a different pair. i 0 58003 The command has been rejected because a Continuous Access pair exists in the same subsystem frame.
Part Code Error Number Error Message Recommended Action 58351 The Quick Restore command has been rejected, because the specified pair is composed of internal and external volumes, and also used as a Continuous Access Journal pair. 7005 7005 Severity Level Failure Level Stop using the specified pair for Continuous Access Journal, or specify a different pair, then retry the operation.
Part Code Error Number Error Message Recommended Action 58493 The PCB required for this operation is not mounted. Check the subsystem configuration. 7005 Severity Level Failure Level Mount the required PCB, then retry the operation. W 5 58520 The operation failed, because different versions of microcodes coexisted in the storage system. Replace the microcode, then retry the operation. E 2 7005 58533 The operation failed, because the specified P-VOL was a journal volume.
Part Code Error Number Error Message Recommended Action 58582 The operation failed because the specified S-VOL was used by XP Snapshot. 7005 Severity Level Failure Level To continue the operation, release the XP Snapshot setting. i 0 58583 The operation failed because the volume was shared by an XP Snapshot pair. To continue the operation, release the XP Snapshot setting. i 0 7005 58584 The operation failed because the volume was shared by an XP Snapshot pair in COPY (RS-R) status.
Table 61 Error Codes — Part Code 7007 Part Code Error Number Error Message Recommended Action 7007 6012 An error occurred during SVP processing. If this problem persists, please call technical support. 7007 7111 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level You cannot create L1 pair for the specified P-VOL. Delete the created L1 pair, and retry the operation. i 0 7010 6504 The number of L1 pairs exceeds the maximum. 7010 6505 The number of L2 pairs exceeds the maximum. You cannot create L2 pair for the specified P-VOL. Delete the created L2 pair, and retry the operation. i 0 7010 7310 Unregistered error code. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue processing, click [OK]. Otherwise, click [Cancel]. W 0 7010 9108 The option has been changed. If you continue processing before applying the change, the option will be reset to the current setting. Do you want to continue processing? 7010 9109 Do you want to execute the Set Over operation? To continue processing, click [OK]. Otherwise, click [Cancel].
Table 63 Error Codes — Part Code 7105 Part Code Error Number Error Message Recommended Action 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 7105 Severity Level Failure Level If this problem persists, call technical support. E 2 5625 You cannot create another pair, because the number of pairs in the group exceeds the maximum. Click [OK].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 0 7105 8504 The command was rejected. The operation failed, because of one of the following reasons: 1. You cannot execute the operation on the specified pair / volume. 2. The pairs of the Normal volume and CV cannot execute QuickRestore. 3. You cannot execute the operation on the intermediate volume. 4.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8515 The number of cylinders in the reserved volume exceeds the maximum. Check the contents, and retry. i 0 7105 8516 The number of S-VOL cylinders exceeds the maximum. Check the contents, and retry. i 0 7105 8517 The number of T-VOL cylinders exceeds the maximum. Check the contents, and retry. i 0 8518 You cannot create a pair, because the track format is different for each.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8533 The emulation type of the specified reserved volume is not supported. Specify the emulation type of the supported volume. i 0 7105 8535 A processor failure was detected. Please call technical support. i 0 7105 8536 A cache failure was detected. Please call technical support. i 0 7105 8537 The cache capacities do not match. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level As the S-VOL, specify a volume that is not used as a command device. i 0 7105 8552 This volume cannot be specified as an S-VOL because it is used as a command device. 7105 8553 The T-VOL is not implemented. You cannot execute the operation for the volume which is not implemented. i 0 7105 8554 The T-VOL cannot be used. Please call technical support, and check if the volume status is normal.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8570 The selected volume does not exist. Refresh the screen, and retry the operation. i 0 7105 8571 The volume is already defined as a reserved volume. Check the contents, and retry. i 0 7105 8572 The volume is already defined as S-VOL. Check the contents, and retry. i 0 7105 8573 The volume is defined as a source volume for Auto LUN. Release the Auto LUN setting.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8589 The specified group name is invalid. Check the contents, and retry. i 0 7105 8590 The group name and the number do not match. Check the contents, and retry. i 0 7105 8591 The specified pair is already set in another group. Check the contents, and retry. i 0 7105 8592 The command was rejected, because the licensed capacity was exceeded. Check the capacity of the installed license key.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Change the status of the Continuous Access pair, then retry the operation. i 0 7105 8607 Cannot change the pair status, because the status of the Continuous Access pair that shares this volume is not Suspend. 7105 8608 The specified T-VOL is not defined. Refresh the screen, and retry the operation. i 0 7105 8609 The specified volume is not set as a reserved volume. Check the status of the volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8628 The operation of the L1 pair failed because the L2 pair was in F-COPY status. Select other pairs. i 0 7105 8629 The status mode specification is invalid. Check the contents, and retry. i 0 7105 8630 The status mode type is invalid. Check the contents, and retry. i 0 7105 8631 The specified CU number is invalid. Please call technical support.
Part Code Error Number Error Message Recommended Action 8645 The Reverse Copy command has been rejected, because the S-VOL is shared as the M-VOL of a Continuous Access pair. Severity Level Failure Level You cannot execute the specified operation. Release the Continuous Access pair for the operation. i 0 8646 The Reverse Copy request was rejected, because the S-VOL was shared with a Continuous Access pair in the non-suspend status. Delete the Continuous Access pair.
Part Code Error Number Error Message Recommended Action 8696 The command has been rejected, because the specified S-VOL is being used as the T-VOL of a Compatible FlashCopy V2 pair. Severity Level Failure Level Release the relationship to delete the Compatible FlashCopy V2 pair, or specify another volume. i 0 8697 The command has been rejected, because the specified T-VOL is being used as the volume of a Compatible FlashCopy V2 pair.
Part Code Error Number Error Message Recommended Action 7105 8994 The command has been rejected, because the storage system is busy. 7105 Severity Level Failure Level Please wait a while, and retry the operation. W 0 8995 The command has been rejected, because the Compatible FlashCopy V2 relationship exists. Withdraw the Compatible FlashCopy V2 relationship. W 0 7105 8996 The command has been rejected, because the storage system is busy. Please wait a while, and retry the operation.
Part Code Error Number Error Message Recommended Action 58004 The command has been rejected because the issued request is an operation that cannot be performed with a volume that can be used from either the mainframe or open-system hosts. Severity Level Failure Level The requested operation cannot be performed. Check the status of the specified volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue the operation, release the Universal Replicator for Mainframe pair or the TrueCopy for Mainframe pair, and retry the operation. i 0 7105 58356 The command was rejected, because the specified volume was used by Universal Replicator for Mainframe and TrueCopy for Mainframe. 7105 58451 The storage system is in internal process. Please retry the operation.
Part Code 7105 7105 7105 Error Number Error Message Recommended Action 58630 The operation failed because the specified S-VOL was used by Delta resync of Universal Replicator for Mainframe. Severity Level Failure Level Release the Universal Replicator for Mainframe setting. W 5 58631 The operation failed because the specified T-VOL was used by Delta resync of Universal Replicator for Mainframe. Release the Universal Replicator for Mainframe setting.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 0 7110 7311 The settings could not be applied. Wait a while, and retry the operation. If the same error occurs despite retrying, Please call technical support. 7110 7312 The password could not be acquired. Please call technical support. W 0 7110 7313 Error details not available. Please call technical support. W 0 7440 An error occurred during processing.
Part Code Error Number Error Message Recommended Action 7110 9378 Do you want to disable the setting to expand the number of relationships? 7110 55003 7110 7110 Severity Level Failure Level To continue processing, click [OK]. To stop processing, click [Cancel]. i 0 The selected T-VOLs include a volume or volumes that is/are paired. Check the selected T-VOLs. i 0 55004 The number of selected S-VOLs doesn't match the number of selected T-VOLs.
Table 65 Error Codes — Part Code 8005 Part Code Error Number Error Message Recommended Action 2002 An error occurred during SVP processing. If this problem persists, please call technical support. 8005 Severity Level Failure Level If this problem persists, call technical support. E 2 2015 A connection error has occurred. Retry the same operation. If the same error occurs despite retrying, call technical support. E 3 8005 2145 A connection error has occurred. Retry the same operation.
Part Code Error Number Error Message Recommended Action 6040 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. 8005 Severity Level Failure Level Please call technical support. E 6 6050 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 8005 6051 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55246 The total number of Cache Residency Manager areas set for the CLPRs and the maximum number of the Cache Residency Manager areas in the subsystem are not equal. Severity Level Failure Level Check the settings, then retry the operation. E 6 55247 The Cache Residency Manager size set for the CLPR is not a multiple of 512 MB. CLPR No:%s Check the settings, then retry the operation.
Table 66 Error Codes — Part Code 8105 Part Code 8105 8105 8105 8105 8105 8105 8105 Error Number Error Message Recommended Action Severity Level Failure Level The specified volume cannot be set as a command device or a component of a LUSE volume, because it is being used as a Continuous Access, Business Copy, Cross-system Copy, Auto LUN, or XP Snapshot volume. Select another volume. Select another volume. E 6 You are trying to set multiple paths to the same volume from one group.
Part Code 8105 8105 8105 8105 8105 8105 8105 338 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. The volume which links as an expanded LU extend over CU#. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 LU path is set to a volume which links as an expanded LU.
Part Code 8105 8105 8105 8105 8105 8105 8105 8105 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. Fibre topology information is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 The specified LU path does not exist.
Part Code 8105 8105 8105 8105 8105 8105 8105 340 Error Number Error Message Recommended Action 1064 You are trying to register the same WWN as the already registered one. Please check the settings and request the setting of the configuration information again. 1065 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again.
Part Code 8105 8105 8105 8105 8105 8105 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. A nickname is not specified when the configuration change of LUN-Security is requested. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 An error occurred.
Part Code 8105 Error Number 1127 Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. CHA high-speed mode is specified to an unmounted CHA. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 E 2 8105 1128 An error occurred. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. When PORT information (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same PORT. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 1136 An error occurred.
Part Code Error Number 8105 8105 8105 8105 8105 8105 8105 8105 344 Error Message Recommended Action 1198 Since a path is defined to an external LU, you cannot set high-speed mode. Severity Level Failure Level Please correct the settings, then retry. E 6 1201 The selection of High Speed mode/MIX mode is invalid. The specified port cannot be changed to High Speed mode/MIX mode. Change the parameter to a path where the High Speed mode/MIX mode can be set, then retry the operation.
Part Code Error Number Error Message Recommended Action 1354 1355 Severity Level Failure Level Failed to add the WWN to the initiator port. The port you are trying to set is for Fibre Continuous Access. You must change the attribute when adding a WWN. Attribute (TarGet or RCU TarGet) E 2 The host mode of the host group connected to the Initiator port cannot be changed. The port you are trying to set is for Fibre Continuous Access. You must change the attribute when adding a WWN.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Select another volume. E 6 8105 1906 The specified volume cannot be set as a command device because it is being used as a virtual volume. 8105 1910 The specified volume contains XP Snapshot pairs. Select another volume. E 6 8105 1911 The specified volume contains Pool-VOLs. Select another volume.
Part Code Error Number Error Message Recommended Action An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. 2082 Severity Level Failure Level A communication error occurs. If the same error occurs despite retrying, call technical support. E 6 Processing is disabled because the host is mounted or the device is reserved. The host is mounted or the device is reserved. Please unmount the host and cancel reservation of the device.
Part Code Error Number Error Message Recommended Action 2515 One of the following is defined: a Continuous Access pair, a Continuous Access Journal pair, or a Universal Replicator for Mainframe pair. Alternatively, command devices defined by Business Continuity Manager are included. Please release the pair definition or delete command devices defined by Business Continuity Manager, and then retry the operation.
Part Code Error Number Error Message Recommended Action 2521 An Auto LUN pair is defined. Cancel the pair definition, cancel the reserve volume, and then retry the operation. 8105 Severity Level Failure Level Cancel the pair definition, cancel the reserve volume, then retry the operation. E 6 2522 An Auto LUN reserved volume is defined. Cancel the reserved volume, and then retry the operation. Cancel the reserved volume, then retry the operation.
Part Code Error Number Error Message Recommended Action 8105 5701 The header is invalid. 8105 5702 8105 Severity Level Failure Level Please check the version information for the first row. E 5 There is no tag. Please write at least one tag. E 5 5705 Configuration File Loader is not installed. Please install the Configuration File Loader. W 5 8105 5710 The specified CHA does not exist. Please correct the name of CHA. W 0 8105 5711 The specified port does not exist.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5751 The group ID does not exist. Please correct the group ID. W 0 8105 5752 The group name does not exist. Please correct the group name. W 0 8105 5753 There is a difference between the current port ID/group ID and the specified one. Please correct the port ID and the group ID. W 0 8105 5754 The intermediate volume cannot be specified as a command device. Please correct the CU and LDEV.
Part Code Error Number Error Message Recommended Action 8105 5789 The intermediate volume cannot be specified as a command device. 8105 5790 8105 Severity Level Failure Level Please correct the CU and LDEV. W 0 A program error occurred under internal process. If nothing changes despite retrying, call technical support. W 0 6012 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code 8105 8105 8105 Error Number 66006 66008 66010 Error Message Recommended Action The number of data items entered in the spreadsheet has exceeded the limit. Severity Level Failure Level Check the spreadsheet, and enter only one serial number under the [SerialNumber] function tag. E 5 The number of digits is invalid. Check the spreadsheet, and set the number of digits of the serial number under the [SerialNumber] function tag to five or less. E 5 The format is invalid.
Part Code Error Number Error Message Recommended Action 8110 5629 The file specified by [File Name on Client] does not exist. 8110 5630 8110 Severity Level Failure Level Correct the specified contents, and retry the operation. E 1 The file specified by [File Name on Client] cannot be read. Correct the specified contents, and retry the operation. E 1 5631 The object specified by [File Name on Client] is not a file. Correct the specified contents, and retry the operation.
Table 69 Error Codes — Part Code 8111 Part Code Error Number Error Message Recommended Action 8111 5627 The file name should be from 1 to 32 characters. 8111 5628 8111 Severity Level Failure Level Correct the specified contents, and retry the operation. E 1 You cannot use following characters for the file name: " \ / : , ; * ? < > | and space. Correct the specified contents, and retry the operation. E 1 5629 The file specified by [File Name on Client] does not exist.
Table 71 Error Codes — Part Code 8305 Part Code Error Number 8305 56524 Error Message Recommended Action This function cannot be used by the storage partition administrator. Select another window. To set this function, contact the storage administrator. Severity Level Failure Level E 3 Table 72 Error Codes — Part Code 8310 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8310 55040 The specified file does not exist.
Part Code Error Number Error Message Recommended Action 6011 An error occurred during SVP processing. If this problem persists, please call technical support. 8505 Severity Level Failure Level If this problem persists, call technical support. E 2 6012 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 8505 6022 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action An invalid SLPR Name was detected. SLPR No:%s 55013 Severity Level Failure Level Correct the SLPR Name, then retry the operation. If this problem persists, call technical support. E 5 Invalid login information was detected. SLPR No:%s Correct the invalid login information, then retry the operation. If this problem persists, call technical support. E 5 55014 This name is already being used as the CLPR name.
Part Code 8505 8505 8505 8505 8505 8505 8505 8505 8505 Error Number Error Message Recommended Action An attempt has been made to either register newly a SLPR that is already registered, or delete a SLPR that is not registered. Severity Level Failure Level Correct the SLPR settings, then retry the operation. If this problem persists, call technical support. E 5 Some parity groups are already registered in a different CLPR. Specify a different parity group, then retry the operation.
Part Code Error Number Error Message Recommended Action 56501 The login information of the partition management function has been initialized due to detection of conflicting information. Please contact the storage administrator. (To the storage administrator: Please reconfigure the login information.) 8505 8505 Severity Level Failure Level Please contact the storage administrator. (To the storage administrator: Please reconfigure the login information.
Part Code 8505 8505 8505 8505 8505 8505 8505 Error Number Error Message Recommended Action 58312 The configuration cannot be changed because the write pending rate of the intended CLPR is too high. Please wait until the write pending rate falls, and then retry the operation. Severity Level Failure Level Please wait until the write pending rate falls, then retry the operation.
Part Code 8505 Error Number 58339 Error Message Recommended Action Access Asynchronous or TrueCopy Asynchronous for Mainframe pair volumes in a CT group. Specify the parity group so that all the pair volumes in CT group are contained. contained or all pair volumes in CT group are contained.
Part Code Error Number Error Message Recommended Action 8510 7440 An error occurred. If this problem persists, please call technical support. 8510 9101 8510 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 Do you want to cancel? To cancel, click [OK]. E 2 9102 Do you want to apply? Click [OK] to execute the operation. E 2 55235 The CLPR name already exists.
Part Code Error Message Recommended Action 57001 The partition configuration may contain some inconsistent information. To initialize partition configuration, select the Yes button. To stop the operation, select the No button. 8510 8510 8510 8510 8510 8510 8510 Error Number Severity Level Failure Level If you clicked [Yes], perform the operation after you set up a SLPR name and other changes. If you clicked [No], restart the operation. If this problem persists, contact the system management.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 9005 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 9005 5201 This functionality is not available. Parallel Access Volume is required. Install the program product. E 6 6001 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action 7117 An error occurred during SVP processing. If this problem persists, please call technical support. 9005 Severity Level Failure Level If this problem persists, call technical support. E 2 7310 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 9005 8001 An error occurred while connecting to the subsystem.
Table 78 Error Codes — Part Code 9010 Part Code Error Number Error Message Recommended Action 9010 7440 An error occurred during processing. If this problem persists, please call technical support. 9010 9303 There are no valid volumes. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 Check the device emulation type or the definition of the journal volume.
Part Code Error Number Error Message Recommended Action 5820 When the host group has a host to which ports are set, the hosts in this host group cannot be registered in another host group. 9105 9105 Severity Level Failure Level Please check the specified host and port. W 0 6012 An error occurred during SVP processing. If this problem persists, please call technical support. An error occurred during SVP processing. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 9105 67002 The specified security group name has already been used by another LDKC. 9105 67003 9105 67004 Severity Level Failure Level Specify another security group name. W 5 The specified host group name has already been used by another LDKC. Specify another host group name. W 5 The specified LDEV Group name has already been used by another LDKC. Specify other LDEV group name.
Part Code Error Number Error Message Recommended Action 9110 5615 The entered name is invalid. Severity Level Failure Level Please click [OK], check the entered name, and retry the operation. W 0 5616 Some attributes of the security group are invalid. Please click [OK], check attributes of the security group, and retry the operation. W 0 5617 Attributes of the security group differ from the attributes of other related security groups.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 9110 7440 An error occurred during processing. If this problem persists, please call technical support. 9110 8111 There is no CHA PCB for mainframe computers. Please install PCBs for the mainframe computers, then retry the operation. W 0 9110 8112 There is no valid volume. Please mount volumes, then retry the operation.
Part Code Error Number 9110 9110 9110 Error Message Recommended Action Severity Level Failure Level 65648 The specified name has already been used by other LDKC. Specify other names. W 0 65662 The data has been changed. The settings will be discarded if you continue the processing. Do you want to switch the LDKC? To continue processing, click [OK]. Otherwise, click [Cancel]. W 5 69020 If you execute this operation, the setting will be executed forcibly.
Part Code Error Number Error Message Recommended Action 7060 An error occurred during SVP processing. If this problem persists, please call technical support. 9205 Severity Level Failure Level If this problem persists, call technical support. E 2 7111 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 9205 7310 This error code is not registered.
Part Code Error Number Error Message Recommended Action 9205 66000 The version number entered in the spreadsheet is incorrect. 9205 66001 9205 Severity Level Failure Level Check the contents of the Volume Retention Manager spreadsheet. E 5 The function name entered in the spreadsheet is incorrect (The function name is not VR). Check the contents of the Volume Retention Manager spreadsheet. E 5 66002 The process mode written in the spreadsheet cannot be specified.
Part Code 9205 9205 9205 Error Number Error Message Recommended Action 66012 The same definition exists in the spreadsheet file. (The combination of a CU number and an LDEV number is repeated.) Severity Level Failure Level Check the contents of the Volume Retention Manager spreadsheet. E 5 66013 The access attribute set in the [Attribute] of the spreadsheet is incorrect (an attribute other than Read/Write, Read Only, or Protect is entered).
Part Code Error Number Error Message Recommended Action 5809 The number of requests for combining LUs does not match the number of the LUs. 9605 Severity Level Failure Level Please review LUs, and retry the operation. E 3 6012 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 9605 6023 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action 9605 8124 This logical volume is a mainframe volume. 9605 8125 9605 Severity Level Failure Level Please specify an open-system volume. E 5 The attribute of the logical volume has been changed by RAID Manager. Please review LDEV information, then retry. E 5 8126 This logical volume is configured as a command device. Please check the logical volume configuration, then retry the operation. E 5 9605 8128 A parameter error occurred.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level You cannot shorten the retention term of the logical volume. To shorten it, call technical support. E 5 9605 8151 You cannot shorten the retention term of the logical volume. If you want to shorten it, please call technical support. 9605 8152 You cannot set a retention term to any mainframe volumes. Please specify an open-systems volume. E 5 9605 8153 The specified retention term exceeds the maximum.
Part Code Error Number Error Message Recommended Action 9605 58414 The attribute of the P-VOL or the S-VOL of the XP Snapshot cannot be changed. 9605 58415 9605 9605 Severity Level Failure Level Please select another volume. E 5 The VMA of the pool volume cannot be changed. Please select another volume. E 5 58416 The VMA of the virtual volume cannot be changed. Please select another volume. E 5 58417 The VMA of the P-VOL or the S-VOL of the XP Snapshot cannot be changed.
Part Code Error Number Error Message Recommended Action 58430 VMA cannot be set to the specified logical volume because the volume is used as a logical volume for iSCSI. 9605 Severity Level Failure Level Release the iSCSI setting or set the VMA to another logical volume. E 5 58432 A VMA cannot be set up on this logical volume because Auto LUN is using the logical volume. Please release Auto LUN's use of the logical volume, or set up the VMA on another logical volume.
Part Code 9605 9605 Error Number Error Message Recommended Action 58447 The command was rejected, because you tried to set VMA to a logical volume with a path set on. 58448 Severity Level Failure Level Select other logical volumes without VMA, or delete the path of the specified logical volume, then retry the operation. E 5 The specified logical volume is blocked, or the LDEV is being formatted or shredded.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue processing, click [OK]. To stop processing, click [Cancel]. i 0 9610 9107 The value that is under setup is not reflected yet. Do you want to continue the operation? 9610 9362 Do you want to change the expiration lock mode? To change the mode, click [OK]. Otherwise, click [Cancel]. i 0 9610 9363 The specified retention term exceeds the maximum.
A Acronyms and Abbreviations Table 86 Acronyms and Abbreviations API application program interface CCI RAID Manager CHA channel adapter CT consistency CTG consistency group CU control unit CV customized volume DASD direct-access storage device DFW DASD fast write DKA disk adapter DKC disk controller IP internet protocol L1, L2 level 1, level 2 LAN local-area network LBA logical block address LCP local control port LDEV logical device LU logical unit LUN logical unit numb
R-VOL remote volume SIM service information message SM shared memory SMPL simplex SNMP simple network management protocol SSID subsystem ID S-VOL secondary volume (Continuous Access), source volume (ShadowImage for Mainframe) SVP service processor T-VOL target volume storage system HP storage system VDEV virtual device WWN worldwide name 384 Acronyms and Abbreviations
