HP StorageWorks Command Console V2.5 User Guide (AA-RV1UA-TE, March 2005)
Table Of Contents
- Contents
- About this Guide
- About SWCC
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
Interpreting SNMP Traps
122 Command Console V2.5 User Guide
"This variable reports the status for the
Power Supply system in the subsystem."
::= { ssEntry 5 }
ssFanStatus OBJECT-TYPE
SYNTAX INTEGER {
ALL_OK(0),
AT_LEAST_1_FAILURE(1)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable reports the status for the
FAN system in the subsystem."
::= { ssEntry 6 }
ssCacheBatteryStatus OBJECT-TYPE
SYNTAX INTEGER {
NORMAL_CHARGE(0),
LOW_CHARGE(1)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable reports the status for the
Cache Battery in the subsystem. This status object is
currently
non-functional but in place for future use."
::= { ssEntry 7 }
ssTemperatureStatus OBJECT-TYPE
SYNTAX INTEGER {
NORMAL(0),
OVER_TEMP_CONDITION(1)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable reports the status for the
Temperature in the subsystem."
::= { ssEntry 8 }
ssCommStatus OBJECT-TYPE
SYNTAX INTEGER {
NORMAL(0),
COMMUNICATION_FAILURE(1)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION