HP StorageWorks Enterprise File Services WAN Accelerator Manager 2.1.
Legal and notice information © Copyright 2005–2006 Hewlett-Packard Development Company, L.P. © Copyright 2003–2006 Riverbed Technology, Inc. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Introduction CONTENTS Contents ........................................................................................................... 9 About This Guide.................................................................................. 9 Types of Users ................................................................................ 9 Organization of This Guide ............................................................ 9 Document Conventions ..........................................................
Completing the Configuration Checklist ............................................ 22 Mounting the EFS WAN Accelerator Manager Appliance to a Rack 23 HP EFS WAN Accelerator Manager Appliance Hardware ................ 23 NIC Port LabelingTerminology Note ................................................. 25 Powering On the HP EFS WAN Accelerator Manager ...................... 26 Connecting to the HP EFS WAN Accelerator Manager ..................... 26 Completing the Initial Configuration.....................
Chapter 4 Managing Remote HP EFS WAN Accelerators ........................ 95 Managing Configurations ................................................................... 95 Managing Configuration Backups................................................ 95 Synchronizing Reporting and Collecting Activity ....................... 97 Upgrading Software on Remote Appliances..................................... 102 Managing Legacy Appliances...........................................................
Managing HP EFS WAN Accelerator Manager Configurations ...... 137 Rebooting the HP EFS WAN Accelerator Manager ......................... 139 Shutting Down the HP EFS WAN Accelerator Manager ................. 140 Chapter 6 Displaying and Customizing HP EFS WAN Accelerator Manager Reports ..................................................................... 141 Displaying Remote Appliances Reports and Logs ........................... 141 Displaying Bandwidth Optimization Reports ............................
Statistics Commands......................................................................... 181 Event Logging Configuration and Viewing Commands................... 184 Event Notification Commands.......................................................... 187 SNMP Commands ............................................................................ 190 Configuration File Management Commands.................................... 199 License Key Commands .........................................................
CONTENTS
INTRODUCTION Introduction In This Introduction Welcome to the HP StorageWorks Enterprise File Services WAN Accelerator Manager User’s Guide. This introduction provides an overview of the information provided in this guide and the documentation conventions used throughout.
Chapter 3, “Setting Up Remote HP EFS WAN Accelerators,” describes how to use the EFS WAN Accelerator Manager to configure remote HP EFS WAN Accelerators. Chapter 4, “Managing Remote HP EFS WAN Accelerators,” describes how to use the EFS WAN Accelerator Manager to manage remote HP EFS WAN Accelerators. Chapter 5, “Managing HP EFS WAN Accelerator Manager Settings,” describes how to modify EFS WAN Accelerator Manager settings.
Meaning Courier Information displayed on your terminal screen and information that you are instructed to enter appear in Courier font. KEYSTROKE Keys that you are to press appear in uppercase letters in Helvetica font. <> Within syntax descriptions, values that you specify appear in angle brackets. For example: interface [] Within syntax descriptions, optional keywords or variables appear in brackets.
Gigabit Ethernet over Copper 1000 Base-T and Fiber 1000 Base-SX (LC connector) (IEEE 802.3 - 2002) The Primary port in the HP EFS WAN Accelerator is 10 Base-T/100, Base-TX/1000, and Base-T/SX Mbps (IEEE 802.3 -2002). In-path HP EFS WAN Accelerator ports are 10/100/1000 Base-TX or Gigabit Ethernet 1000Base-T/SX (IEEE 802.3 – 2002) (depending on your order). The HP EFS WAN Accelerator supports Virtual Local Area Network (VLAN) Tagging (IEEE 802.1Q - 2003).
Additional Resources This section describes resources that supplement the information in this guide.
TCP/IP Illustrated, Volume I, The Protocols by W. R. Stevens (Addison-Wesley, 1994) Internet Routing Architectures (2nd Edition) by Bassam Halabi (Cisco Press, 2000) Contacting HP This section describes how to contact HP. Technical Support Telephone numbers for worldwide technical support are listed on the following HP web site: http://www.hp.com/support. From this web site, select the country of origin. For example, the North American technical support number is 800-633-3600.
In This Chapter Overview of the HP EFS WAN Accelerator Manager This chapter provides an overview of HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager) features.
HP EFS WAN Accelerator Manager Configuration Objects The HP EFS WAN Accelerator Manager utilizes appliance profiles and appliance groups to facilitate centralized configuration and reporting. You use profiles as configuration templates to ensure proper configuration for groups of HP EFS WAN Accelerators that must have the same configuration for common network settings, routing rules, and feature settings.
Appliance wa-1, for example, receives its configuration information from the Base and CIFS groups, which are defined by the Base and CIFS profiles. Appliance wa-1 reports to the all group, the CIFS group, and the Europe group. HP EFS WAN Accelerator Auto-Registration HP EFS WAN Accelerators must be registered with the HP EFS WAN Accelerator Manager so that you can monitor and manage them with HP EFS WAN Accelerator Manager tools.
an initial group assignment (optional) 5. Set up a DNS server to map the host name hpwam to the IP address for the HP EFS WAN Accelerator Manager. 6. Connect the remote HP EFS WAN Accelerator primary network interface to the network and power it on.
Customizable Reports You can also create a custom dashboard of the metrics reported on the Welcome and Summary report pages. For details, see Chapter 6, “Displaying and Customizing HP EFS WAN Accelerator Manager Reports.” Scheduled Operations You can set operations, such as software upgrades and configuration changes, to run during off-peak hours. Although these processes are not time consuming, they might interrupt traffic, and it is recommended to schedule these operations during off-peak hours.
HP EFS WAN Accelerator Manager Command-Line Interface The HP EFS WAN Accelerator Manager has a command-line interface (CLI) which contains a subset of the commands available on the HP EFS WAN Accelerator. NOTE: The HP EFS WAN Accelerator Manager CLI cannot be used to configure remote HP EFS WAN Accelerators. It can only be used to configure the HP EFS WAN Accelerator Manager. For details, see Appendix A, “HP EFS WAN Accelerator Manager Command-Line Interface.
In This Chapter Installing and Configuring the HP EFS WAN Accelerator Manager This chapter describes how to install and configure the HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager).
One rail kit HP StorageWorks EFS WAN Accelerator Documentation Set CD-ROM If any items are damaged or missing, go to http://www.hp.com/support for replacement or repair. Preparing Your Site for Installation This section lists the prerequisites to installation. Ensure your site meets the following requirements: A standard electronic environment where the ambient temperature between 10º C and 35º C (50º F and 95º F) and the relative humidity is between 10% and 90% (non-condensing).
EFS WAN Accelerator Manager Appliance Host name IP address 2 - INSTALLING AND CONFIGURING THE HP EFS Netmask Default gateway Domain Name Server (DNS) IP address Domain Name Remote HP EFS WAN Accelerators Serial number IP address or host name User name Password Mounting the EFS WAN Accelerator Manager Appliance to a Rack To mount the HP EFS WAN Accelerator Manager to a rack, refer to the instructions that came with your rack.
Item Description 1 PCI-X expansion slot 2, full-length 64 bit/133 MHz 3.3 V (optional PCI Express slot 1, x8) 2 PCI-X expansion slot 1, low-profile half-length 64 bit/100 MHz 3.3 V 3 Power supply 4 UID button/LED 5 10/100/1000 NIC 1 6 10/100/1000 NIC 2 7 iLO management port 8 Serial connector 9 Mouse connector 10 Keyboard connector 11 Video connector 12 USB connectors Figure 2-2.
Item Description Status 2 Internal health LED Green = System health is normal. Red = System critical. Off = System health is normal (when in standby mode). 3 NIC 1 link/activity LED Green = Network link exists. Flashing green = Network link and activity exist. Off = No link to network exists. 4 NIC 2 link/activity LED Green = Network link exists. Flashing green = Network link and activity exist. Off = No link to network exists. 5 Drive activity LED Green = Drive activity is normal.
Powering On the HP EFS WAN Accelerator Manager This section describes how to connect and power on the HP EFS WAN Accelerator Manager. To connect the power to the HP EFS WAN Accelerator Manager 1. Plug in the Alternating Current (AC) power cord into the HP StorageWorks Enterprise File Services WAN Accelerator Manager. 2. Plug in the AC power cord into an uninterrupted AC power source (Figure 2-1 on page 23, item 3). 3.
Completing the Initial Configuration To configure the HP EFS WAN Accelerator Manager 1. After you log in to the HP EFS WAN Accelerator Manager as administrator, the system prompts you to start the configuration wizard. Enter yes at the system prompt. For example: Configuration wizard. Do you want to use the wizard for initial configuration? yes 2. Complete the configuration wizard steps as described in the following table. TIP: Press ENTER to enter the default value.
Step 3: Primary IP address? Enter the IP address for the HP EFS WAN Accelerator Manager. Step 3: Primary IP address? 10.0.0.74 Step 4: Netmask? Enter the netmask for the network on which the HP EFS WAN Accelerator Manager is to reside. Step 4: Netmask? 255.255.0.0 Step 5: Default gateway? 10.0.0.1 Enter the default gateway for the network on which the HP EFS WAN Accelerator Manager is to reside. Step 5: Default gateway? 10.0.0.
Connecting the HP EFS WAN Accelerator Manager to Your Network To connect the HP EFS WAN Accelerator Manager to your network • Plug the straight-through cable provided in your shipment into the Primary port of the HP EFS WAN Accelerator Manager and the LAN switch (this can be any port on your LAN switch that acts as a host). Figure 2-3.
Logging in to the HP EFS WAN Accelerator Manager This section describes how to log in to the HP EFS WAN Accelerator Manager. You can connect to the HP EFS WAN Accelerator Manager through any supported Web browser. To connect to the HP EFS WAN Accelerator Manager you must know the host, domain, and administrator password that you assigned during the initial setup of the HP EFS WAN Accelerator Manager. NOTE: Cookies and Javascript must be enabled in your browser.
2. In the Account text box, the default account admin appears. You must specify the account admin when you first log in. For information on these options, see “Managing Accounts on the HP EFS WAN Accelerator Manager” on page 124. 3. In the Password text box, type the password you assigned in the HP EFS WAN Accelerator Manager configuration wizard. 4. Click Login to log in and display the Home: Welcome page. Figure 2-5.
The HP EFS WAN Accelerator Manager Home: Welcome Page This topic describes the HP EFS WAN Accelerator Manager Home: Welcome page. By default, the Home: Welcome page reports the following information for groups and individual HP EFS WAN Accelerators. Field Description System Uptime Specifies the time since the last reboot of the HP EFS WAN Accelerator Manager. Model Specifies the HP EFS WAN Accelerator model number. Version Specifies the software version.
Using Tabs and Menus This topic describes how to navigate to HP EFS WAN Accelerator Manager tools and reports using hyperlinked tabs and menus. Figure 2-6. HP EFS WAN Accelerator Manager Home: Welcome Page Click tabbed pages to display configuration and administration tools, reports, and online help. Click Logout to log out of the system. Click the Printer icon to print a page or report. Click the Book icon to display online help. .
When you click a hyperlinked tab, a menu for the tasks you can perform appears on the left of the HP EFS WAN Accelerator Manager. For example, when you click the Setup Manager tab, the Setup Manager menu appears. Menu items are hyperlinks to pages that display tools and reports to help you manage and administer your HP system. When you click a menu item, you display the primary tool or report for the menu choice. The following table summarizes the purpose of each tabbed page.
To print pages and reports To display online help This topic describes how to display the online help that describes each page of the HP EFS WAN Accelerator Manager and the tasks that you can perform. • Click the Book icon in the upper right-side of the page. The HP EFS WAN Accelerator Manager displays help for the page in a new browser window. Logging Out To log out of the HP EFS WAN Accelerator Manager This topic describes how to log out of the HP EFS WAN Accelerator Manager. • Click Logout.
2 - INSTALLING AND CONFIGURING THE HP EFS WAN ACCELERATOR MANAGER
In This Chapter Setting Up Remote HP EFS WAN Accelerators This chapter describes how to implement the HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager) profiles and groups that you use to manage and monitor the HP EFS WAN Accelerators in your network. When you initially deploy HP EFS WAN Accelerators, you perform the following tasks. Task Reference 1. Create configuration profiles.
Using Profiles This section describes how to create and manage HP EFS WAN Accelerator profiles.
Creating Common Profiles Before you can set the configuration elements, you must create a new, empty configuration profile. 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Profiles in the left menu to display the Profiles page. Figure 3-1. Setup Appliances: Profiles Page TIP: If the profile list contains profiles, click the link in the Profile Name column to examine the profile commands and determine whether an existing profile suits your needs.
To enable in-path or out-of-path support 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click General Settings in the left menu to display the Profile - General Settings page. Figure 3-2.
4. Use the controls to set base service settings for a profile, as described in the following table. Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. In-Path Enable In-Path Support. Check this box to enable in-path support. Reset Existing Client Connections on Startup. Check this box to enable kickoff.
Setting In-Path Rules You set in-path configuration rules for a common profile in the Profile - In-Path Rules page. An in-path rule defines the policies for intercepting traffic for optimization. To set in-path rules 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click In-Path Rules in the left menu to display the Profile - In-Path Rules page. Figure 3-3.
Control Description Add New Rule Type. Select one of the following rule types from the drop-down list: • Fixed-Target. Fixed-target rules directly specify out-of-path appliances near the target server. Determine which servers you would like a particular appliance to optimize (and, optionally, which ports), and add rules to specify the Target Appliance and a Backup Appliance IP address and port. NOTE: In an out-of-path deployment, if you want to optimize MAPI Exchange by destination port.
Control Description Advanced Options Optimization Policy. Optionally, if you have selected a Fixed Target rule, you can configure the following types of optimization policies: • Normal. Perform Lempel-Ziv (LZ) compression and Scalable Data Referencing (SDR). • SDR-Only. Perform SDR; do not perform LZ compression. • Compression-Only. Perform LZ compression; do not perform SDR. • None. Do not perform SDR or LZ compression.
Control Description Additional Options Pass-Through Traffic for Known Secure Ports. Automatically pass-through traffic on commonly secure ports (for example, ssh, https, and smtps). Pass-Through Traffic for Known Interactive Ports. Automatically pass-through traffic on interactive ports (for example, telnet, echo, rlogin, rsh, Citrix ICA, VNC, X Window system). For a list of interactive ports that are automatically forwarded, see “Interactive Ports Automatically Forwarded by the HP System” on page 220.
4. Use the controls to set CIFS features for a profile, as described in the following table. Control Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. General Disable Write Optimization. Check this box to disable write optimization. Disable write optimization only if you have applications that assume and require writethrough in the network.
5. Click Apply to Working to apply these settings to the specified working profile. 6. To save the settings permanently, click Save. To revert to the running configuration, click Reset. Setting MAPI Features You set Messaging Application Protocol Interface (MAPI) features for a common profile in the Profile - Protocol: MAPI page. Enabling this feature is optional. To enable MAPI features 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2.
4. Use the controls to set MAPI features for a profile, as described in the following table. Control Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. MAPI Exchange 2003 MAPI Exchange 2003. Type the MAPI Exchange 2003 port if you have an internal firewall specifying a port for Exchange data. This option is not commonly changed. NOTE: In an out-of-path deployment, if you want to optimize MAPI Exchange by destination port.
Setting MS-SQL Features You set Microsoft Structured Query Language (SQL) support for a common profile in the Profile - Protocol: SQL page. The MS-SQL blade also optimizes other database applications but you must define SQL rules to obtain maximum optimization. If you are interested in enabling the MSSQL blade for other database applications, contact HP professional services. Enabling this feature is optional. To enable MS-SQL features 1.
4. Use the controls to set MS-SQL features for a profile, as described in the following table. Control Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. Add MS-SQL Port Port. Type the port number for the MS-SQL server in the text box and click Add Port. To remove ports from the port list, click the check box next to the port name and click Remove Selected Ports. MS-SQL Features Enable MS-SQL Optimization.
To enable connection pooling 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. Figure 3-7. Setup Appliances: Profile - Connection Pooling Page 4. Use the controls to set pooling size for a profile, as described in the following table. Control Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list.
The QoS feature allows you to map a destination port to a Differentiated Services Codepoint (DSCP) level for optimized connections. The DSCP level corresponds to the DiffServ DSCP field in the IP packets header. After you map a destination port and a DSCP level, every packet corresponding to the connection with that destination port has the DSCP field set to that value in the forward and backward direction.
4. Use the controls to set QoS features for a profile, as described in the following table. Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. Add New Rule Source Subnet. Type the IP address for the source subnet in the Source Subnet text box. Use the following format: 0.0.0.0/0. Destination Subnet. Type the IP address for the destination subnet in the text box. Use the following format: 0.0.0.0/0. Port.
To set-up alarms 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Reports in the left menu to expand the Reports menu and display the Profile - Alarm Settings page. Figure 3-9. Setup Appliances: Profile - Alarm Settings Page 4. Use the controls to set alarms for a profile, as described in the following table.
Description Warning Temperature Alarm Raise Alarm When Temperature (°C) Reaches. Check this box to trigger the alarm when the CPU temperature exceeds the rising threshold. When the temperature is lowered to the reset threshold value, the alarm is cleared. The default rising threshold value for CPU temperature is 70º C. The warning temperature threshold must be lower than the critical temperature threshold. Rising Threshold. Type a whole number to specify temperature (º C). Reset Threshold.
To set-up email notification 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Reports in the left menu to expand the Reports menu. 4. Click Notification in the left menu to display the Profile - Notification page. Figure 3-10. Setup Appliances: Profile - Notification Page 5. Use the controls to configure notification parameters for a profile, as described in the following table.
Control Description Settings Report Events to SNMP Agent. Check this box to report activity to an SNMP agent. Report Failures via Email. Check this box to report failures via email. Use the Notification Recipients controls to specify email addresses. SMTP Server. Type a valid SMTP server. External DNS and external access for SMTP traffic is required for this feature to function. SMTP Port. Type a port number for the SMTP server. Update.
To set-up SNMP settings 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Reports in the left menu to expand the Reports menu. 4. Click SNMP Settings in the left menu to display the Profile - SNMP Settings page. Figure 3-11. Setup Appliances: Profile - SNMP Settings Page 5. Use the controls to configure SNMP for a profile, as described in the following table.
Setting SNMP Trap Receivers 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Reports in the left menu to expand the Reports menu. 4. Click SNMP Trap Receivers in the left menu to display the Profile - SNMP Trap Receivers page. Figure 3-12. Setup: Reports - SNMP Trap Receivers Page 5. Use the controls to configure SNMP trap receivers for a profile, as described in the following table.
6. To save the settings permanently, click Save. To revert to the running configuration, click Reset. Setting Monitored Ports You set ports to be monitored for a common profile in the Profile - Monitored Ports page. The ports set to be monitored for a remote HP EFS WAN Accelerator must match the ports to be monitored by the HP EFS WAN Accelerator Manager. For details on setting ports monitored by the HP EFS WAN Accelerator Manager, see “Setting Up Monitored Ports” on page 118.
5. Use the controls to set ports to be monitored for a profile, as described in the following table. Description Settings will be applied to profile Select the name of the profile you want to configure from the drop-down list. Port Type the port to be monitored. Description Type a description for the monitoring activity. Add Click Add to add the port to the Monitored Port list.
To set the log severity level and log rotation 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Logging in the left menu to expand the Logging menu and display the Profile: Logging - General Settings page. Figure 3-14. Setup Appliances: Profile - Logging - General Settings Page 4. Use the controls to configure local logging parameters for a profile, as described in the following table.
Setting Remote Logging 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Common Profiles in the left menu to expand the Common Profiles menu. 3. Click Logging in the left menu to expand the Logging menu. 4. Click Remote Log Servers in the left menu to display the Profile - Logging Remote Log Servers page. Figure 3-15. Setup Appliances: Profile - Logging - Remote Log Servers Page 5. Use the controls to set-up remote logging for a profile, as described in the following table.
Managing Profiles Displaying the Profile List To display the profile list This section describes how to manage the profile list and how to add additional CLI commands to a profile. It includes the following topics: “Displaying the Profile List,” next “Adding CLI Commands to a Profile” on page 64 You display the profile list in the Profiles page. 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Profiles in the left menu to display the Profiles page. Figure 3-16.
To add CLI commands to a profile 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Profiles in the left menu to display the Profiles page. Figure 3-17. Setup Appliances: Profile: 4. Use the controls to review and add CLI commands to the Commands list, as described in the following table. Control Description Configuration Comment. Enter a comment that describes the commands you are adding to the profile. Update.
Sending Profiles You send the profile settings to HP EFS WAN Accelerator groups in the Send Profiles page. You send profile settings to an appliance group whenever you modify the profile settings. Profile settings do not take effect on a group until they are sent. To send profile settings to groups 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Send Profiles in the left menu to display the Send Profiles page. Figure 3-18. Setup Appliances: Send Profiles Page 3.
Control Description Select Target Type List. Select Group or Appliance from the left-hand drop-down list to populate the second drop-down list with group names or appliance names. Setup Execution Schedule for later? Click this box if you do not want to run the operation immediately. Date. Type the date to run the operation, following the format YYYY/MM/DD. Time. Type the time to run the operation, following the format HH:MM:SS.
Using Groups This section describes how to create and manage HP EFS WAN Accelerator groups. It includes the following topics: “Creating Groups,” next “Associating Profiles with Groups” on page 69 “Assigning Appliances to Groups” on page 71 For detailed information about the relationship between profiles, groups, and appliances, see “HP EFS WAN Accelerator Manager Configuration Objects” on page 16. Creating Groups You create HP EFS WAN Accelerator groups in the Appliance Groups page.
TIP: If the group list contains groups, click the link in the Group column to examine the group configuration and determine whether an existing group suits your needs. If so, you do not need to configure a new group. If not, continue with the procedures in this section. Control Description Name Type a descriptive name for the profile. Enable auto configuration? Click this box to enable auto-configuration for new appliances. Enable backups? Click this box to enable backups.
To associate a profile with a group 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Groups in the left menu to display the Appliance Group page. 3. Click the name of the group for which you want to associate one or more profiles to display the Appliance Group: page. Figure 3-20. Setup Appliances: Appliance Group Page 4. Use the controls to associate one or more profiles with the specified group, as described in the following table.
5. To save the settings permanently, click Save. To revert to the running configuration, click Reset. You assign HP EFS WAN Accelerators to groups in the Organize Appliances page. An appliance can belong to more than one group. For example, you might assign an appliance to one or more configuration-based groups (for example, a CIFS group and a MAPI group) and one or more reporting-based groups (for example, an ASIASTATS group and a EUROPESTATS group).
3. Use the controls to assign appliances to one or more groups, as described in the following table. Control Description Toolbar Click this button to remove selected appliances from group assignments. Appliances removed from all group assignments are automatically placed in the Orphans group. Click this button to expand the list of appliances in groups. Click this button to hide the list of appliances in groups. Group List.
Remote appliances must be registered with the HP EFS WAN Accelerator Manager so that you can monitor and manage them with HP EFS WAN Accelerator Manager tools. If the remote appliance has not auto-registered, you can use the HP EFS WAN Accelerator Manager to register the appliance. If you auto-register an appliance, the remote appliance is auto-configured when you connect it to the network. To register an appliance 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2.
3. Use the Register New Appliance controls to register new appliances, as described in the following table. Control Description Serial Number Type the serial number for the appliance you want to register. Hostname/IP Address Type the appliance host name or IP address in the text box. NOTE: If the appliance contacts the HP EFS WAN Accelerator Manager with a new host name, this value is overwritten. Username Type the user name of the remote administrator user in the text box.
To modify registration settings 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliances in the left menu to display the Appliances page. Figure 3-23. Setup Appliances: Appliance: Page HP EFS WAN ACCELERATOR MANAGER USER ’S GUIDE 75 3 - SETTING UP REMOTE HP EFS WAN ACCELERATORS 3. Click the name of the appliance whose registration you want to modify to display the Appliance: page.
4. Use the controls to modify the appliance registration settings, as described in the following table. Control Description Local Configuration Hostname/IP Address. To modify the host name or IP address, type a new value in the text box. Auto-config. Select Defer to Group’s Setting, Enable, or Disable from the drop-down list to set auto-configuration preferences. Backup. Select Defer to Group’s Setting, Enable, or Disable from the drop-down list to set backup preferences. Config Pushes.
To set the host name 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliance Specific in the left menu to expand the Appliance Specific configuration menu. 3. Click Hostname in the left menu to display the Hostname page. Figure 3-24. Setup Appliances: Hostname Page 4. Use the controls to view or modify the configuration, as described in the following table.
Setting the Primary Interface You modify settings for the remote HP EFS WAN Accelerator primary interface in the Primary Interface page. NOTE: If you completed the installation wizard when you initially set up the remote appliance, you already set this parameter. If you chose to complete the appliance configuration through the HP EFS WAN Accelerator Manager when you initially set up the remote appliance, you must set the interface settings as described below to complete the remote appliance configuration.
4. Use the controls to view or modify the configuration, as described in the following table. Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list. IP Address Get IP address automatically? Check this box to obtain the IP address from a dynamic host configuration protocol (DHCP) server. If you do not use a DHCP server to set the IP address, specify the following settings: • IP Address.
You specify the in-path interface if you plan to have the appliance in the direct path (the same subnet) as the client and the server in your network. You also set the in-path gateway (WAN router). NOTE: If you completed the installation wizard when you initially set up the remote appliance, you already set this parameter.
4. Use the controls to complete the configuration, as described in the following table. Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list. Select interface Select an in-path interface from the drop-down list, for example, inpath0_0. IP Address Get IP address automatically? Check this box to obtain the IP address from a dynamic host configuration protocol (DHCP) server.
Control Description Additional Interface Settings LAN Speed. Select the speed from the drop-down list to set the speed for the in-path LAN port. The default value is Auto. If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface. The speed and duplex must match (LAN and WAN) in an in-path configuration.
Setting Auxiliary Interfaces You set up an auxiliary interface which provides an additional management interface for a secondary network in the AUX Interface page. You cannot have the Primary and Auxiliary ports on the same subnet. Enabling this interface is optional. To set an auxiliary interface 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliance Specific in the left menu to expand the Appliance Specific configuration menu. 3.
4. Use the controls to complete the configuration, as described in the following table. Control Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list. AUX Interface Enabled Check this box to enable the auxiliary interface. Auxiliary interface provides an additional management interface for a secondary network. You cannot have the Primary and Auxiliary ports on the same subnet.
To set a static network route 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliance Specific in the left menu to expand the Appliance Specific configuration menu. Figure 3-28. Setup Appliances: Routing Page 4. Use the controls to complete the configuration, as described in the following table. Control Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list.
Complete static in-path route configuration only if your network requires additional static network routing rules. To set a static, in-path network route 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliance Specific in the left menu to expand the Appliance Specific configuration menu. 3. Click Routing: In-Path in the left menu to display the In-Path Routing page. Figure 3-29. Setup: In-Path Routing Page 4.
Setting the DNS You set up Domain Name Service (DNS) for the remote HP EFS WAN Accelerator in the DNS Settings page. NOTE: If you completed the installation wizard when you initially set up the remote appliance, you already set this parameter. If you chose to complete the appliance configuration through the HP EFS WAN Accelerator Manager when you initially set up the remote appliance, you can set this parameter as described below to complete the remote appliance configuration. To set the DNS server 1.
4. Use the controls to complete the configuration, as described in the following table. Control Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list. Name Servers Set one or more of the following: • Primary DNS IP. Type the IP address for the primary name server in the text box. • Secondary DNS IP. Optional. Type the IP address for the secondary name server in the text box. • Tertiary DNS IP. Optional.
To set IP address-host name pairs 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Appliance Specific in the left menu to expand the Appliance Specific configuration menu. 3 - SETTING UP REMOTE HP EFS WAN ACCELERATORS 3. Click Hosts in the left menu to display the Hosts page. Figure 3-31. Setup Appliances: Hosts Page 4. Use the controls to complete the configuration, as described in the following table.
Enabling IPsec support makes it difficult for a third party to view your data or pose as a machine you expect to receive data from. You must also specify a shared secret to enable IPsec support. To enable IPsec authentication you must have at least one encryption and authentication algorithm specified. Only optimized data is protected, pass-through traffic is not. Enabling IPsec support is optional. To enable authentication and encryption 1.
4. Use the controls to view or modify the configuration, as described in the following table. Description Settings will be applied to appliance Select the appliance for which you want to view or modify the configuration from the drop-down list. Add New Peer Peer IP. Type the IP address for the peer appliance. Add Peer. To add the peer specified in the Peer IP box, click Add Peer.
NOTE: If a connection has not been made between the two appliances that are configured to use IPsec security, then the Peers list does not display the peer appliance because a security association has not been established. The Peers list appears in the Summary report.
5. Click Apply to Working to apply these settings to the specified appliance. 6. To save the settings permanently, click Save. To revert to the running configuration, click Reset. HP EFS WAN ACCELERATOR MANAGER USER ’S GUIDE 93 3 - SETTING UP REMOTE HP EFS WAN ACCELERATORS When you apply page settings, the values are applied to the running configuration but not saved permanently. The Save Configuration icon displays a flashing orange arrow to remind you to save your configuration.
3 - SETTING UP REMOTE HP EFS WAN ACCELERATORS
In This Chapter Managing Remote HP EFS WAN Accelerators This chapter describes how to use the HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager) to back up and push out remote appliance configurations; how to start, stop, and reboot remote HP EFS WAN Accelerator services; and how to push out software upgrades to remote appliances.
NOTE: Typically, you would not need to use backups. HP recommends you restore an appliance to health by re-sending its configuration profiles. If using profiles for restoration is not possible, you can use the procedure described next to restore the system to the backup restore point. However, the restore point does not include profile and appliance-specific settings.
3. Use the controls to back up or restore the remote appliance configuration, as described in the following table. Description View backups for the appliance Select the name of the appliance whose configuration you want to back up from the dropdown list. Configuration Backups List The Configuration Backups list includes the backup name, type, and creation time for backups of the remote appliance configuration. If you know you no longer need a backup, click the check box and click Remove Selected.
To synchronize reporting 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Snyc Report Setup in the left menu to display the Synchronize page. Figure 4-2. Setup Appliances: Synchronize Page 3. If synchronization status is sorted into four categories: Synced, Not Synced, Unknown, or Disconnected. 4. Select all in the Unknown list and click Check Synchronization. The page redisplays, identifying synchronized and unsynchronized remote appliances. 5.
Managing Remote Appliances This section includes the following topics: “Starting, Stopping, and Restarting the HP EFS WAN Accelerator Service,” next “Rebooting Appliances” on page 100 “Shutting Down Appliances” on page 101 NOTE: When you stop the HP EFS WAN Accelerator service, the appliance appears in reports with the status critical. The status appears OK once the appliance is back online.
3. Use the controls to select an action to be run on remote appliances, as described in the following table. Control Description Choose Action Options From the Action Type drop-down list, choose one of the following options: Start. Select Start to start service which has stopped. Stop. Select Stop to stop active service. Restart. Select Restart to stop active service and then start service. Optionally, select the Clean the data store box to reset the data store on the next restart.
To reboot remote appliances 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Reboot Appliances to display the Reboot Appliances page. 4 - MANAGING REMOTE HP EFS WAN ACCELERATORS Figure 4-4. Setup Appliances: Reboot Appliances Page 3. Use the controls to select an action to be run on remote appliances, as described in the following table. Control Description Choose Action Options Optionally, select the Clean the data store box to reset the data store on the next restart.
To shutdown remote appliances 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Shutdown Appliances to display the Shutdown Appliances page. Figure 4-5. Setup Appliances: Shutdown Appliances Page 3. Use the controls to select an action to be run on remote appliances, as described in the following table. Control Description Choose Action Options Optionally, select the Clean the data store box to reset the data store on the next restart.
You can upgrade groups of appliances from a Uniform Resource Locator (URL) or from a local file via File Transfer Protocol (FTP). You can also revert to a previous version of the software. To upgrade software 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Click Upgrade Software in the left menu to display the Upgrade Software page. Figure 4-6. Setup Appliances: Upgrade Software Page 3.
Managing Legacy Appliances You manage legacy HP EFS WAN Accelerators—appliances that are not compatible with the current version of the HP EFS WAN Accelerator Manager—in the Legacy Appliances page. HP recommends you unregister legacy appliances or upgrade them to a compatible software version so that you can experience the benefits of full compatibility with your version of the HP EFS WAN Accelerator Manager.
Remote appliances with incompatible software versions appear in the Legacy Appliances list. 3. Manage legacy appliances as described in the following table. Description Unregister Selected Appliances To unregister legacy appliances, select them and click Unregister Selected Appliances.
To upgrade software on legacy appliances 1. Click the Setup Appliances tab to expand the Setup Appliances menu. 2. Under Legacy in the left menu, click Upgrade Software to display the Legacy Upgrade Software page. Figure 4-8. Setup Appliances: Legacy - Upgrade Software 3. Use the controls to select a software image and remote appliances for upgrade, as described in the following table. Control Description Legacy Appliance Group Select All or another legacy group name from the drop-down list.
In This Chapter Managing HP EFS WAN Accelerator Manager Settings When you installed and initially configured the HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager), you specified host and network settings. Together with the HP EFS WAN Accelerator Manager default settings, the HP EFS WAN Accelerator Manager is fully operational.
Setting Network Parameters This section describes how to configure the local network parameters for the HP EFS WAN Accelerator Manager.
To modify settings for the primary interface You modify settings for the HP EFS WAN Accelerator Manager primary interface in the Networking - Primary Interface page. During the initial configuration of the HP EFS WAN Accelerator Manager, you configured most of the settings for the primary interface. Modify your settings in the Primary Interface page. 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Interface: Primary to display the Networking - Primary Interface page. Figure 5-2.
3. Use the controls to view or modify the configuration, as described in the following table. Control Description IP Address Obtain IP Address Automatically. Check this box to obtain the IP address from a dynamic host configuration protocol (DHCP) server. Specify IP Address Manually. If you do not use a DHCP server to set the IP address, specify the following settings: • IP Address. Type an IP address in the text box. • Subnet Mask. Type a subnet mask in the text box. • Primary Gateway.
To configure static network routes 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Routing to display the Networking - Routing page. 5 - MANAGING HP EFS WAN ACCELERATOR MANAGER Figure 5-3. Setup Manager: Networking - Routing Page 3. Use the controls to complete the configuration, as described in the following table. Control Description Add New Route Destination. Type the IP address in the text box. Netmask. Type the subnet mask in the text box. Gateway.
To set the DNS server 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click DNS Settings to display the Networking - DNS Settings page. Figure 5-4. Setup Manager: Networking - DNS Settings Page 3. Use the controls to complete the configuration, as described in the following table. Control Description Name Servers Set one or more of the following: • Primary DNS IP. Type the IP address for the primary name server in the text box. • Secondary DNS IP. Optional.
To map host names to IP addresses 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Hosts to display the Networking - Hosts page. 5 - MANAGING HP EFS WAN ACCELERATOR MANAGER Figure 5-5. Setup Manager: Networking - Hosts Page 3. Use the controls to complete the configuration, as described in the following table. Control Description Add New Host Host IP. Type the IP address for the host. Hostname. Type a host name. Add Entry.
Configuring Event Notification This section describes how to set event notification. By default, events are reported only to the HP EFS WAN Accelerator Manager. Follow the procedures in this section to set email or Simple Network Management Protocol (SNMP) notification parameters.
3. Use the controls to set alarms for a profile, as described in the following table. Description CPU Alarms Raise Alarm When CPU Utilization Reaches. Check this box to trigger an alarm if the average and peak threshold for the Central Processing Unit (CPU) utilization is exceeded. When an alarm reaches the rising threshold, it is activated; when it reaches the lowest or reset threshold, it is reset. After an alarm is triggered, it is not triggered again until it has fallen below the reset threshold.
To set email notification 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Reports in the left menu to expand the Reports menu. 3. Click Notification to display the Reports - Notification page. Figure 5-7. Setup Manager: Reports - Notification Page 4. Use the controls to configure email notification parameters, as described in the following table. Control Description Events Report Events to SNMP Agent. Check this box to report activity to an SNMP agent.
5. Click Apply to apply the setting to the running configuration. 6. To save the settings permanently, click Save. To revert to the running configuration, click Reset. Setting SNMP Parameters To set SNMP parameters You set SNMP parameters in the Reports - SNMP Settings page. By default SNMP parameters are not configured. Set SNMP parameters for the SNMP contact and location in the SNMP Settings page. 1. Click the Setup Manager tab to expand the Setup Manager menu. 2.
Setting SNMP Traps To set SNMP traps You set SNMP traps in the Reports - SNMP Trap Receivers page. The default setup does not complete SNMP traps. 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Reports in the left menu to expand the Reports menu. 3. Click SNMP Trap Receivers to display the Reports - SNMP Trap Receivers page. Figure 5-9. Setup Manager: Reports - SNMP Trap Receivers Page 4. Use the controls to configure SNMP trap receivers, as described in the following table.
The ports set to be monitored for the HP EFS WAN Accelerator Manager must match the ports to be monitored for remote appliances. For details on setting ports monitored for appliances, see “Setting Monitored Ports” on page 60. 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Reports in the left menu to expand the Reports menu. 3. Click Monitored Ports to display the Reports - Monitored Ports page. Figure 5-10. Setup Manager: Reports - Monitored Ports Page 4.
Setting HP EFS WAN Accelerator Manager Logging Options This section describes how to set local and remote logging for the HP EFS WAN Accelerator Manager. This section includes the following topics: Setting HP EFS WAN Accelerator Manager Local Logging To set local logging “Setting HP EFS WAN Accelerator Manager Local Logging,” next “Setting HP EFS WAN Accelerator Manager Remote Logging Servers” on page 121 You set local logging for the HP EFS WAN Accelerator Manager in the Logging Local page.
3. Use the controls to configure local logging parameters, as described in the following table. Description Log Filtering Minimum Severity. Select a severity level from the drop-down list. All log messages with this severity level or higher are logged. Log Rotation Rotate every. From the first drop-down list, select None, Daily, Weekly, or Monthly. Rotate when log reaches. Type a file size in MB. Keep at most __ log file(s). Type a number to indicate the maximum number of logs to store.
To set remote logging 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Logging in the left menu to expand the Logging menu. 3. Click Remote to display the Logging - Remote page. Figure 5-12. Setup Manager: Logging - Remote Page 4. Use the controls to set-up remote logging for a profile, as described in the following table. Control Description Server IP Type the IP address for the server on which to maintain the syslog.
Setting the Date and Time 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Date & Time in the left menu to display the Set Date & Time - Set Clock page. Figure 5-13. Setup Manager: Set Date & Time - Set Clock Page 3. Use the following controls to set the HP EFS WAN Accelerator Manager clock. Control Description Set Time Using NTP Time Synchronization Check this box to enable NTP time synchronization.
To set an NTP server 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Date & Time in the left menu to expand the Date & Time menu. 3. Click the NTP Servers tab to display the Date & Time - NTP Servers page. Figure 5-14. Setup Manager: Date & Time - NTP Servers Page 4. Use the controls to complete the configuration, as described in the following table. Control Description Add New NTP Server Server IP. Type the IP address for the NTP server in the text box. Version.
This section includes the following topics: “Setting HP EFS WAN Accelerator Manager Authentication Methods,” next “Setting Up RADIUS Server Authentication” on page 126 “Setting the Monitor User Password” on page 131 “Setting Up RADIUS Server Authentication” on page 126 “Setting Up TACACS+ Server Authentication” on page 128 You prioritize authentication methods you choose to support in the Authentication General Settings page.
3. Use the controls to complete the configuration, as described in the following table. Control Description Login Page Default Login ID. Type a default login identification number (ID) in the text box. Authentication Methods Method 1. Select Local, RADIUS, or TACACS+ from the drop-down list. Note: Make sure you put the authentication methods in the order in which you want them to occur.
To set up RADIUS server authentication 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Authentication in the left menu to expand the Authentication menu. Figure 5-16. Setup Manager: Authentication - RADIUS Servers Page 4. Use the Add New RADIUS Server controls to complete the configuration for a new server, as described in the following table. Control Description Add New RADIUS Server Server IP. Type the server IP address in the text box. Authentication Port.
5. Optionally, use the Global Settings controls to set global configuration parameters for any new servers you add to the Server list. Control Description Global Settings Server Key. Type the server key in the text box. (If you add a new server to your network and you do not specify these fields at that time, the global settings are applied automatically.) Timeout. Type the time-out period in the text box. Retries.
To set up TACACS+ server authentication 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Authentication in the left menu to expand the Authentication menu. Figure 5-17. Setup Manager: Authentication: TACACS+ Servers Page 4. Use the Add New TACACS+ Server controls to complete the configuration for a new server, as described in the following table. Control Description Add New TACACS+ Server Server IP. Type the server IP address in the text box. Authentication Port.
5. Optionally, use the Global Settings controls to set global configuration parameters for any new servers you add to the Server list. Control Description Global Settings Server Key. Type the server key in the text box. (If you add a new server to your network and you do not specify these fields at that time, the global settings are applied automatically.) Timeout. Type the time-out period in the text box. Retries.
4. Use the Change Password controls to complete the configuration, as described in the following table. Description Change Password New Password. Type the new administrator password in the text box. The password must have a minimum of 6 characters. Confirm New Password. Retype the new administrator password in the text box. 5. To save the settings permanently, click Save. To revert to the running configuration, click Reset.
Updating HP EFS WAN Accelerator Manager Licenses You update HP EFS WAN Accelerator Manager licenses in the Licenses page. To update a license 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Licenses in the left menu to display the Licenses page. Figure 5-20. Setup Manager: License Page 3. Use the controls to complete the configuration, as described in the following table.
Upgrading or Reverting Software Versions To upgrade or revert software version 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Upgrade Software in the left menu to display the Software Upgrade page. Figure 5-21. Setup Manager: Software Upgrade Page 3. Use the controls to complete the desired process, as described in the following table. Control Description Install Software Install from a URL.
Displaying Job Status You display the status of jobs you or another administrator might have scheduled in the Scheduled Jobs page. To display job status 1. Click Setup Manager to expand the Setup Manager menu. 2. Click Scheduled Jobs to display the Scheduled Jobs page. Figure 5-22. Setup Manager: Scheduled Jobs Page The Scheduled Jobs page lists pending and completed jobs, as well as jobs that resulted in errors or have become inactive and need to be re-run. 3.
To set preferences 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Web Preferences in the left menu to display the Web Preferences page. 5 - MANAGING HP EFS WAN ACCELERATOR MANAGER Figure 5-23. Setup Manager: Web Preferences Page 3. Use the controls to select any of the following statistics to be included on the Home: Welcome page and Reports: Summary page. Field Description Reduction Specifies the total decrease of data transmitted over the WAN.
Total Connections Specifies the total active (in the last 60 seconds) connections optimized. Optimized Connections Specifies the total connections optimized. Passthrough Connections Specifies the total connections passed through, unoptimized, when the connection limit has been reached. Half-Opened Connections Specifies the total half-opened active connections. A half-opened connection is a TCP connection in which the connection has not been fully established.
Managing HP EFS WAN Accelerator Manager Configurations The HP EFS WAN Accelerator Manager configuration stores settings for remote HP EFS WAN Accelerators, the HP EFS WAN Accelerator Manager, and HP EFS WAN Accelerator Manager administrative objects (profiles and groups)—basically, all settings you can set with the HP EFS WAN Accelerator Manager.
To manage applied, active, or backup configurations 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Configuration Manager in the left menu to display the Configuration Manager page. Figure 5-24. Setup Manager: Configuration Manager Page 3. Use the controls to manage configurations, as described in the following table. Control Description Save Configuration Click Save Configuration to save settings that have been applied to the running configuration.
Rebooting the HP EFS WAN Accelerator Manager Rebooting the HP EFS WAN Accelerator Manager disrupts existing network connections. Rebooting can take a few minutes. To reboot the HP EFS WAN Accelerator Manager 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Reboot to display the Reboot Manager page. Figure 5-25. Setup Manager: Reboot Manager Page 3. Click Reboot Manager. After you click Reboot Manager, you are logged out of the system, and it is rebooted.
Shutting Down the HP EFS WAN Accelerator Manager You shut down the HP EFS WAN Accelerator Manager in the Shutdown Manager page. To restart the system you must manually turn on the HP EFS WAN Accelerator Manager. To shutdown the HP EFS WAN Accelerator Manager 1. Click the Setup Manager tab to expand the Setup Manager menu. 2. Click Shutdown to display the Shutdown Manager page. Figure 5-26. Setup Manager: Shutdown Manager Page 3. Click Shutdown Manager.
Displaying and Customizing HP EFS WAN Accelerator Manager Reports In This Chapter This chapter describes how to display and customize remote HP EFS WAN Accelerator reports, download remote appliance logs, and display and customize HP EFS WAN Accelerator Manager reports.
The Bandwidth Optimization report provides the following statistics that describe bandwidth activity for the time period you specify. Field Description WAN Data Specifies the Bytes sent over the Wide Area Network (WAN). LAN Data Specifies the Bytes over the Local Area Network (LAN). Total Data Reduction % over Last Week Specifies the total decrease of data transmitted over the WAN. Peak Data Reduction % over Last Week Specifies the peak decrease in data transmitted over the WAN.
2. Use the controls to customize the report, as described in the following table. Description Period Select Last Hour, Last Day, Last Week, or Last Month from the Period drop-down list. Traffic Select Bi-directional, WAN-to-LAN, or LAN-to-WAN from the drop-down list. Application Select FTP, HTTP, CIFS:NetBIOS, CIFS:TCP, or MAPI from the drop-down list. The default value is All. Appliances The default is to include all appliances.
To display the Throughput report 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Throughput to display the Remote Appliances - Throughput page. Figure 6-2. .Reports: Remote Appliances - Throughput Page 3. Use the controls to customize the report, as described in the following table. Control Description Period Select Last Hour, Last Day, Last Week, or Last Month from the Period drop-down list.
The Connection History report provides the following statistics that summarize connection activity. Description Total Optimized Specifies the total active connections optimized. Established Specifies the total established active connections. Half Opened Specifies the total half-opened active connections. A half-opened connection is a TCP connection in which the connection has not been fully established.
To create the Connection History report 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Connection History to display the Remote Appliances - Connection History page. Figure 6-3. Reports: Remote Appliances - Connection History Page 3. Use the controls to customize the report, as described in the following table. Control Description Period Select Last 5 Minutes, Last Hour, Last Day, Last Week, or Last Month from the Period drop-down list.
The Connection Counts report provides the following statistics that summarize the active connection count as of last polling. Polling occurs every 5 minutes. Description Established Specifies the total established active connections. Half Opened Specifies the total half-opened active connections. A half-opened connection is a TCP connection in which the connection has not been fully established.
To create Connection Counts report 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Connection Counts to display the Remote Appliances - Connection Counts page. Figure 6-4. Reports: Remote Appliances - Connection Counts Page 3. Use the controls to customize the report, as described in the following table. Control Description Appliances The default is to include all appliances.
To download remote appliance logs 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Logs to display the Remote Appliances - Download Logs page. 6 - DISPLAYING AND CUSTOMIZING HP EFS WAN Figure 6-5. Reports: Remote Appliances - Download Logs Page 3. Use the controls to select the logs you want to download, as described in the following table. Control Description Drop-down list Select Appliance or Group from the left drop-down list.
TIP: To print your report, click the Printer icon in the upper right corner of the page. Displaying the Summary Report You display the Summary report in the Summary page. The Summary report lists the remote appliances that are connected to the HP EFS WAN Accelerator Manager. By default, the Summary report provides a dashboard view of the following metrics. Field Description System Uptime Specifies the time since the last reboot. Model Specifies the appliance model number.
To display the Summary report 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Summary to display the Remote Appliances - Summary page. 6 - DISPLAYING AND CUSTOMIZING HP EFS WAN Figure 6-7. Reports: Remote Appliances - Summary Page. 3. Use the controls to customize the report, as described in the following table. Control Description Appliances The default is to include all appliances.
Displaying the Appliance Details Report You display the Appliance Details report in the Appliance: page. The Appliance Details report provides the following statistics for an appliance. Packet Type Description Status Provides high level status for the appliance: healthy, warning, critical. Also provides hardware model number, software version details, and links to the appliance logs and Management Console. Performance Reduction.
To display the Appliance Details Report 1. Click the Reports tab to display the Reports menu. 2. Under Remote Appliances in the left menu, click Summary to display the Remote Appliances - Summary page. Figure 6-8. Reports: Remote Appliances - Appliance Details Page TIP: To print the report, click the Printer icon in the upper right corner of the page. Displaying HP EFS WAN Accelerator Manager Reports and Logs This section describes how to display HP EFS WAN Accelerator Manager reports and logs.
Displaying the Alarm Status Report You display the HP EFS WAN Accelerator Manager Alarm Status report in the Alarm Status page. The Alarm Status report contains the following table of statistics that summarize traffic activity by application. Alarm Description Central Processing Unit (CPU) Utilization Whether the system has reached the CPU threshold for any of the HP EFS WAN Accelerators. If the system has reached the CPU threshold, check your settings.
The CPU Utilization report includes the following table of statistics that describe CPU activity for the time period you specify. To create the CPU Utilization report Description Average Percent Utilization for CPU 1 Specifies the average CPU utilization. Peak Percent Utilization for CPU 1 Specifies the peak CPU utilization.
The Memory Paging report includes the following table of statistics that describe memory paging activity for the time period you specify. Field Description Total Pages Swapped Out Specifies the total number of pages swapped. If 100 pages are swapped approximately every two hours the HP EFS WAN Accelerator Manager is functioning properly. If thousands of pages are swapped every few minutes, contact technical support. Average Pages Swapped Out Specifies the average number of pages swapped.
NOTE: To print your report, click the Printer icon in the upper right corner of the page. To view system dump files You display the HP EFS WAN Accelerator Manager System Dumps report in the System Dumps page. The HP EFS WAN Accelerator Manager System Dumps report displays a list of system dump files and their size. A system dump contains a copy of the kernel data on the system. System dump files can help you diagnose problems with the HP EFS WAN Accelerator Manager. 1.
To display the System Snapshot report 1. Click the Reports tab to display the Reports menu. 2. Under HP EFS WAN Accelerator Manager in the left menu, click System Snapshots to display the System Snapshots page. Figure 6-13. Reports: HP EFS WAN Accelerator Manager - System Snapshots Page 3. To view the system file, click the check box next to the file name. The system file appears in a new browser window. TIP: To remove a file, click the check box next to the entry and click Remove Selected Files.
To display HP EFS WAN Accelerator Manager logs 1. Click the System Log tab to display the System Log page. Figure 6-14. System Log Page 6 - DISPLAYING AND CUSTOMIZING HP EFS WAN 2. Type a keyword or string in the Filter text box and click Filter to filter logs. 3. At the top of the Event list, click the page number to view additional pages for the log. To view previous pages, click Prev. TIP: Click the Disk icon in the upper right corner to download the log file to your local machine.
6 - DISPLAYING AND CUSTOMIZING HP EFS WAN ACCELERATOR MANAGER REPORTS
In This Appendix HP EFS WAN Accelerator Manager Command-Line Interface This appendix describes how to access and use the HP StorageWorks Enterprise File Services WAN Accelerator Manager (HP EFS WAN Accelerator Manager) commandline interface (CLI).
Using the Command-Line Interface This section assumes you have already performed the initial setup of the HP EFS WAN Accelerator Manager using the configuration wizard. To connect the CLI 1. You can connect to the CLI using one of the following options: An ASCII terminal or emulator that can connect to the serial console. It must have the following settings: 9600 baud, 8 bits, no parity, 1 stop bit, and no flow control.
The commands available to you depend on which mode you are in. Entering a question mark (?) at the system prompt provides a list of commands for each command mode. Access Method System Prompt Exit Method Description user Each CLI session begins in user mode. host > exit • Perform common network tests such as ping. privileged Enter the enable command at the system prompt while in user mode. host # disable • Restart and reboot the system. no enable • Display system information.
tilden (config) # logging files enable % Unrecognized command "enable". Type "logging files ?" for help. If a command is incomplete, the following message is displayed: tilden (config) # logging % Incomplete command. Type "logging ?" for help. Command Negation You can type the no command before many of the commands to negate the syntax. Depending on the command or the parameters, command negation disables the command or returns the parameter to the default value.
cli default paging enable Sets paging so that it is enabled each time you log in. With paging enabled, if there is too much text to fit on the page, the CLI prompts you for the next page of text. The no command option disables paging. Syntax cli default paging enable Parameters None Example minna (config) # cli default paging enable minna (config) # cli session Description Sets CLI options for current session only.
Terminal type: Auto-logout: Paging: CLI defaults for Auto-logout: Paging: xterm 15 minutes enabled future sessions 15 minutes enabled show terminal Description Displays terminal settings. Syntax show terminal Parameters None Example minna # show terminal Terminal width: 80 columns Terminal length: 24 rows Terminal type: xterm Enable Configuration Mode and Persistence Commands This section describes configuration mode and persistence commands for the HP EFS WAN Accelerator Manager.
Parameters None Example minna # disable minna > A - HP EFS WAN ACCELERATOR MANAGER enable Description Enters privileged-mode. Syntax enable Parameters None Example minna > enable minna # exit Description Exits the CLI when in non-privileged-mode; exits privileged mode when in privileged mode; exits configuration-mode when in configuration mode.
does not terminate existing ssh sessions; it only prevents new sessions from being established. Syntax ssh server enable Parameters None Example minna (config) # ssh server enable minna (config) # show ssh server Description Displays the server settings.
Example minna (config) # ssh client user authorized-key rsakey minna (config) # Description Enables ssh interface restrictions to the system. The no command option disables ssh interface restrictions which causes ssh to accept connections from all interfaces. After you have enabled interface restrictions, you must specify which interfaces to accept connections on using the ssh server listen interface command. If the list of interfaces is empty, all interfaces are accepted.
Example minna (config) # ssh server listen interface 10.1.1.1, 10.0.0.4 minna (config) # User Accounts Commands This section describes user account commands for the HP EFS WAN Accelerator Manager.
Example minna (config) # username admin password xyzzzZ minna (config) # Description Sets the password for the specified user. The password must be a minimum of 6 characters.The password is returned in cleartext format on the command line. Syntax username password 0 Parameters Example Specifies the user login: admin or monitor. Specifies the password. The password must be a minimum of 6 characters.
“ntp peer” on page 173 “ntp server” on page 174 “show clock” on page 174 “show ntp” on page 174 clock set Description Sets the system time and date. Syntax clock set { | } Parameters Example Specifies the hour, minutes, and seconds. Specifies the year, month, and day. minna (config) # clock set 12:34:55 minna (config) # clock timezone Description Sets the current time zone. The default value is Greenwich Mean Time (GMT-offset).
ntpdate Conducts a single time synchronization with a specified Network Time Protocol (NTP) server. Syntax ntpdate A - HP EFS WAN ACCELERATOR MANAGER Description Parameters Example Specifies the NTP server to synchronize with. minna (config) # ntpdate 10.10.10.1 minna (config) # ntp disable Description Disables NTP support. The no command option enables NTP support.
ntp server Description Configures an NTP server. The no command option removes an NTP server. Syntax ntp server [version ] Parameters Example Specifies the NTP server to synchronize with. version Specifies the version number for NTP. You do not need to specify the version number for the no ntp server command. minna (config) # ntp server 10.10.10.1 minna (config) # show clock Description Displays current date and time.
“interface duplex” on page 175 “interface speed” on page 176 “interface dhcp” on page 176 “interface shutdown” on page 176 “show interface” on page 177 Interface records for interfaces not detected by the system cannot be implicitly created by setting options on them. They must be explicitly created using the interface create command. interface Description Configures network interface address. The no command option disables the interface settings.
interface speed Description Configures network interface speed setting. The no command option disables the interface speed settings. Syntax interface { speed } Parameters Example Specifies the interface name: aux, primary. speed Specifies the speed setting for the interface in Megabits per second. minna (config) # interface lan speed 100 minna (config) # interface dhcp Description Enables Dynamic Host Configuration Protocol (DHCP) on the interface.
show interface Displays interface settings for specified interface or all interface settings if one is not specified. Syntax interface {} [configured | brief] Parameters Example Specifies the interface name: aux, lan, wan, primary, in-path. configured | brief Displays interface settings. brief Displays the abbreviated runtime state, with the interface statistics excluded.
hostname Description Sets the host name for this system. The no command option removes the hostname for this system. Syntax hostname Parameters Example Specifies the host name. Do not include the domain name. minna (config) # hostname nova nova (config) # ip name-server Description Sets the DNS name server. The no command option unsets the DNS name server. Syntax ip name-server Parameters Example Specifies the IP address. minna (config) # ip name-server 10.
Parameters Specifies the host name. Specifies the IP address. A - HP EFS WAN ACCELERATOR MANAGER Example minna (config) # ip host park 10.10.10.1 minna (config) # show hosts Description Displays HP system hosts. Syntax show hosts Parameters None Example minna # show hosts Hostname: minna Name server: 10.0.0.0 (configured) Domain name: example.com (configured) Domain name: example.com (configured) IP 127.0.0.
ip route Description Adds a static route. The no command option disables the static route. If no ip route command is called with no parameters, it removes all static routes. If it is called with only a network prefix and mask, it deletes all routes for that prefix. Syntax ip route { } Parameters Example Specifies the network prefix. Specifies the netmask. Specifies the next hop IP address.
arp Creates static Address Resolution Protocol (ARP) entries in the ARP table. The no command option disables ARP static entries. Syntax arp A - HP EFS WAN ACCELERATOR MANAGER Description Parameters Example Specifies the IP address of the machine. Specifies the Media Access Control (MAC) address. minna (config) # arp 10.0.0.0 00:07:E9:55:10:09 minna (config) # clear arp-cache Clears dynamic entries in the ARP cache.
“stats clear-all,” next “stats sample” on page 182 “stats chd” on page 182 “stats alarm” on page 183 “show stats” on page 183 stats clear-all Description Clears all statistics. Syntax stats clear-all Parameters None Example minna (config) # stats clear-all minna (config) # stats sample Description Configure sampled statistics.
Parameters Specifies the specific data point: bw_5min, bw_day, bw_hour, bw_month, bw_week, bws_week, bwt_5min, bwt_day, bwt_hour, bwt_month, bwt_week, conns_5min, conns_day, conns_hour, conns_month, conns_week, cpu_util, cpu_util_ave, cpu_util_day, fs_mnt_day, fs_mnt_month, fs_mnt_week, memory_day, paging, paging_day, rbt_cpu_day, rbt_paging_day, throughput_5min, throughput_day, throughput_hour, throughput_month, throughput_week. clear Clears all data.
Parameters Example alarm Displays alarm statistics. Specify alarm type or : bypass, cpu_util_ave, paging, raid_error, raid_warning, swversion. bandwidth all [lan-towan | wan-to-lan | bidirectional] | [ports [all | [hour | day | week | month]]] Displays bandwidth statistics. cpu Displays CPU statistics. memory Displays memory statistics. data reduction [hour | day| week | month] Displays throughput statistics for the last hour, day, week, or month.
Parameters Specifies the hostname for the syslog server. trap Specifies the trap log level of the syslog server. If you have set different log levels for each remote syslog server, this command changes all remote syslog servers to have a single log level. minna (config) # logging nova minna (config) # logging files delete Description Deletes a specified number of log files. Syntax logging files delete [oldest ] Parameters oldest Example Deletes the oldest log files.
Parameters Specifies the logging severity level. The following severity levels are supported: • emerg. Emergency, the system is unusable. • alert. Action must be taken immediately. • crit. Critical conditions. • err. Error conditions. • warning. Warning conditions. • notice. Normal but significant condition. • info. Informational messages. • debug. Debug-level messages.
show log Displays system logs. Syntax show log [continuous | files ] Parameters Example continuous Displays the log continuously, similar to the tail -f command. files Displays a list of log files or a specific log file. minna # show log Dec 22 20:00:00 localhost /usr/sbin/crond[784]: logrotate /etc/logrotate.conf) Dec 22 20:00:00 localhost cli[555]: [cli.INFO]: signal 2 (SIGINT) Dec 22 20:02:31 localhost cli[555]: [cli.
email domain Description Sets the domain name from which the emails come from. If not set, the first domain name configured using the ip domain-list command is used. The host name does not appear in the return address, only the domain name. Syntax email domain Parameters Example Specifies the domain name for email notification.
Parameters minna (config) # email notify events recipient example@example.com minna (config) # email notify failures enable Description Enables email notification of appliance failures such as core dumps. The no command option disables this command. Syntax email notify failures Parameters None Example minna (config) # email notify failures enable minna (config) # email notify failures recipient Description Enables email notification of appliance failures such as core dumps.
Syntax show email Parameters None Example minna # show email Mail hub: Domain: example.com (default) Event emails Enabled: yes No recipients configured. Failure emails Enabled: yes No recipients configured. Autosupport emails Enabled: yes recipient:autosupport@autosupport.example.com Mail hub:autosupport.example.com SNMP Commands This section describes the Simple Network Mail Protocol (SNMP) commands.
Syntax snmp-server community Parameters Example A - HP EFS WAN ACCELERATOR MANAGER Specifies the name of the SNMP server community. minna (config) # snmp-server community ReaDonLy minna (config) # snmp-server contact Description Sets the SNMP server contact. The no command option disables the SNMP server contact. Syntax snmp-server contact Parameters Example Specifies the name of the SNMP server community contact.
Syntax Example snmp-server {host traps traps version } host Specifies the host name or IP address for the SNMP server. traps Sets the SNMP trap on a community. traps version Specifies the SNMP trap version number and community name.
“tacacs-server key” on page 198 “tacacs-server retransmit” on page 198 “tacacs-server timeout” on page 198 Description Configures RADIUS or TACACS+ login settings. The order in which the methods are specified is the order in which the authentication is attempted. The no aaa command option clears all authentication states and returns user authentication to the local user name database.
Parameters Usage Specifies the order in which to apply the authentication policy: remote-only, remote-first, local-only. The order determines how the remote user mapping behaves. If the authenticated user name is valid locally, no mapping is performed.The setting has the following behaviors: remote-first. If a local-user mapping attribute is returned and it is a valid local user name, map the authenticated user to the local user specified in the attribute.
Parameters Specifies the RADIUS server host name or IP address. auth-port Specifies the authorization port number. The default value is 1812. timeout Sets the timeout for retransmitting a request to any RADIUS server. The range is 1-60. The default value is 3. retransmit Specifies the number of times the client attempts to authenticate with any RADIUS server. The default value is 1. The range is 0-5. To disable retransmissions set it to 0.
radius-server retransmit Description Specifies the number of times the client attempts to authenticate with any RADIUS server. This command can be overridden in a radius-server host command. The no command option resets the value to the default value. Syntax radius-server retransmit Parameters Example Specifies the number of times the client attempts to authenticate with any RADIUS server. The range is 0-5. The default value is 1.
show tacacs Parameters None Example minna # show tacacs TACACS+ defaults: key: timeout: 3 retransmit: 1 No TACACS+ servers configured. A - HP EFS WAN ACCELERATOR MANAGER Syntax tacacs-server host Description Adds a TACACS+ server to the set of servers used for authentication. Some of the parameters given can override the configured global defaults for all TACACS+ servers. The no command option disables TACACS+ support.
Example minna (config) # tacacs-server host 10.0.0.0 minna (config) # tacacs-server key Description Sets the shared secret text string used to communicate with any TACACS+ server. The tacacs-server key command can be overridden using the tacacs-server host command. The no command option resets the value to the default value. Syntax tacacs-server key Parameters Example Sets the shared secret text string used to communicate with any TACACS+ server.
Example minna (config) # tacacs-server timeout 30 minna (config) # This section describes the configuration file management commands for the HP EFS WAN Accelerator Manager.
Syntax configuration delete Parameters Example Specifies the name of the configuration file. minna (config) # configuration delete westcoast minna (config) # configuration factory Description Creates a new, blank configuration file, without licenses. Syntax configuration factory Parameters Example Specifies the name of the new configuration file.
configuration jump-start Reruns the configuration wizard. Syntax configuration jump-start Parameters None Example minna (config) # configuration jump-start configuration wizard. A - HP EFS WAN ACCELERATOR MANAGER Description Step 1: Hostname? [telegraph] Step 2: Use DHCP? [no] Step 3: Primary IP address? [10.0.0.73] Step 4: Netmask? [255.255.0.0] Step 5: Default gateway? [10.0.0.1] Step 6: Primary DNS server? [10.0.0.2] Step 7: Domain name? [example.
Usage To merge a configuration file, run the following set of commands: configuration write to ;; this saves the current config to the new name and activates ;; the new configuration configuration fetch ;; this fetches the configuration from the remote appliance configuration merge ;; this merges the fetched config into the active configuration ;; which is the newly named/created one in step 1 above configuration delete
configuration revert saved Parameters None Example minna (config) # configuration revert saved minna (config) # configuration switch-to Description Loads a configuration file and makes it the active configuration. For an example of usage, see “configuration merge” on page 201. Syntax configuration switch-to { | initial | initial.bak} Parameters Example Specifies the name of the configuration file to switch to. initial Specifies the initial configuration. initial.
write terminal Description Displays commands to recreate current running configuration. Syntax write terminal Parameters None Example minna (config) # write terminal show configuration Description Displays the current, saved configuration settings that differ from the default settings. Syntax show configuration Parameters None Example minna # show configuration ## Network interface configuration no interface primary dhcp interface primary duplex "auto" interface primary ip address 10.0.02.
show configuration full Displays all configuration settings including the default settings. Syntax show configuration full Parameters None Example minna # show configuration full displays the full complete configuration. A - HP EFS WAN ACCELERATOR MANAGER Description show configuration running Description Displays running configuration settings. The show configuration running full command displays all settings including default settings.
license install Description Installs a new software license key. Syntax license install Parameters Example Specifies the license key. minna (config) # license install XXXX_X-XXXX-X-XXXX-XXXX minna (config) # show licenses Description Displays active licenses.
Syntax image boot Parameters Example Specifies the partition to boot: 1 or 2. A - HP EFS WAN ACCELERATOR MANAGER minna (config) # image boot 1 minna (config) # image delete Description Deletes the specified software image. Syntax image delete Parameters Example Specifies the software image to delete. minna (config) # image delete snkv1.0 minna (config) # image fetch Description Downloads a software image from a remote host.
Parameters Example Specifies the software image filename. Specifies the partition number: 1, 2. minna (config) # image install version1.0 2 minna (config) # image move Description Moves or renames an inactive system image on the hard disk. Syntax image move Parameters Example Specifies the name of the software image to move or rename. Specifies the new name of the software image.
Manager/linux Manager/linux Manager/linux Manager/linux Manager/linux show version history Description Displays history of image upgrades. Syntax show version history Example #minna # show version history rbt_sh 2.1.6 #37 2006-03-31 21:44:41 i386 root@munich:repository/ rapanui_37 Web Commands This section describes the Web commands for the HP EFS WAN Accelerator Manager.
web auto-logout Description Sets the number of minutes before the HP EFS WAN Accelerator Management Console automatically logs out the user. The default value is 15 minutes. The no command option disables the automatic log out feature. Syntax web auto-logout Parameters Example Specifies the number of minutes before the system automatically logs out the user. minna (config) # web auto-logout 20 minna (config) # web enable Description Enables the Management Console.
Example minna (config) # web http port 8080 minna (config) # Description Enables the Management Console with Secure Socket Layer (SSL) support, that is secure Web support. The no command option disables SSL port support. Syntax web https enable Parameters None Example minna (config) # web https enable minna (config) # web https port Description Sets the secure Web port on which the HTTPS Management Console can be reached. The default value is 443.
web session timeout Description Sets the session timeout value. This is the amount of time the cookie is active. The default value is 60 minutes. The no command option resets the session timeout to the default value. Syntax web session timeout Parameters Example Specifies the number of minutes. minna (config) # web session timeout 120 minna (config) # Diagnostic Commands This section describe the diagnostic commands for the HP EFS WAN Accelerator Manager.
Parameters [} The following options are supported: Example minna # ping minna PING minna.example.com (10.0.0.3) 56(84) bytes of data. 64 bytes from minna.example.com (10.0.0.3): icmp_seq=1 ttl=64 time=0.038 ms 64 bytes from minna.example.com (10.0.0.3): icmp_seq=2 ttl=64 time=0.024 ms reload Description Reboots the HP EFS WAN Accelerator Manager. If the clean option is specified, the data store is cleared before reboot occurs.
Parameters Example To view options, enter slogin at the system prompt. minna # slogin -l usertest tcpdump Description Executes the tcpdump utility. The tcpdump command takes the standard Linux options. TIP: You can write tcpdump to a file using the -w option so that you can analyze them. Syntax tcpdump [] Parameters [] Example The tcpdump command takes the standard Linux options. minna # tcpdump tcpdump: listening on primary 18:59:13.682568 minna.example.com.
Parameters minna # traceroute minna traceroute to minna.example.com (10.0.0.3), 30 hops max, 38 byte packets 1 minna (10.0.0.3) 0.035 ms 0.021 ms 0.013 ms TCP Dump Capture Commands This section describes tcpdump commands for the HP EFS WAN Accelerator Manager. It contains the following commands: “file tcpdump,” next “show files tcpdump” on page 215 file tcpdump Description Deletes or uploads a tcpdump file.
Hardware Commands This section describes Error-Correcting Code (ECC) memory commands for the HP EFS WAN Accelerator Manager. It contains the following commands: “hardware ecc-mem-check enable,” next “reset factory reload” on page 216 “show hardware” on page 216 hardware ecc-mem-check enable Description Enables Error-Correcting Code (ECC) memory check. The no command option disables ECC memory check.
In This Appendix HP EFS WAN Accelerator Manager Specifications This appendix summarizes the technical specifications and status lights for the HP EFS WAN Accelerator Manager. This appendix includes the following sections: “Technical Specifications,” next “Environmental Specifications” on page 218 Technical Specifications The following tables summarizes the physical and power specifications for the HP EFS WAN Accelerator Manager.
Environmental Specifications The following table summarizes the environmental requirements for the HP EFS WAN Accelerator Manager.
In This Appendix C - HP SYSTEM PORTS APPENDIX C HP System Ports This appendix describes the HP system default, secure, and interactive ports. It contains the following sections: “Default Ports,” next “Commonly Optimized Ports” on page 219 “Interactive Ports Automatically Forwarded by the HP System” on page 220 “Secure Ports Automatically Forwarded by the HP System” on page 220 Default Ports The HP system uses the following default ports.
7830 Interactive Ports Automatically Forwarded by the HP System The following interactive ports are automatically forwarded by the HP system. Port Description 7 TCP ECHO 23 Telnet 37 UDP/Time 107 Remote Telnet Service 513 Remote Login 514 Shell 3389 MS WBT Server, TS/Remote Desktop 5631 PC Anywhere 5900-5903 VNC 6000 X11 For detailed information about how to set interactive port forwarding, see “Setting Monitored Ports” on page 60.
Port Description ftps 990/tcp ftp protocol, control, over TLS/SSL telnets 992/tcp telnet protocol over TLS/SSL imaps 993/tcp imap4 protocol over TLS/SSL pop3s 995/tcp pop3 protocol over TLS/SSL (was spop3) l2tp 1701/tcp l2tp pptp 1723/tcp pptp tftps 3713/tcp TFTP over TLS The following table contains the uncommon ports automatically forwarded by the HP system.
Type Port Description jboss-iiop-ssl 3529/tcp JBoss IIOP/SSL ibm-diradm-ssl 3539/tcp IBM Directory Server SSL can-nds-ssl 3660/tcp Candle Directory Services using SSL can-ferret-ssl 3661/tcp Candle Directory Services using SSL linktest-s 3747/tcp LXPRO.
GLOSSARY Glossary ARP. Address Resolution Protocol. An IP protocol used to obtain a node's physical address. Bandwidth. The upper limit on the amount of data, typically in kilobits per second (kbps), that can pass through a network connection. Greater bandwidth indicates faster data transfer capability. Bit. A Binary digit. The smallest unit of information handled by a computer; either 1 or 0 in the binary number system. Blade.
FDDI. Fiber Distributed Data Interface. A set of American National Standards Institute (ANSI) protocols for sending digital data over fiber optic cable. FDDI networks are token-passing networks, and support data rates of up to 100 Mbps (100 million bits) per second. FDDI networks are typically used as backbones for WideArea Networks (WANs). Filer. An appliance that attaches to a computer network and is used for data storage. Gateway.
Internet. The collection of networks tied together to provide a global network that use the TCP/IP suite of protocols. IP. Internet protocol. Network layer protocol in the TCP/IP stack that enables a connectionless internetwork service. IPsec. Internet Protocol Security Protocol. A set of protocols to support secure exchange of packets at the IP layer. IPsec has been deployed widely to implement Virtual Private Networks (VPNs). IPsec supports two encryption modes: Transport and Tunnel.
state algorithms to send routing information to all nodes in an internetwork by calculating the shortest path to each node based on a topography of the Internet constructed by each node. Each router sends that portion of the routing table (keeps track of routes to particular network destinations) that describes the state of its own links, and it also sends the complete routing structure (topography). Packet. A unit of information transmitted, as a whole, from one device to another on a network. Probe.
A aaa authentication login default 193 aaa authorization map default-user 193 aaa authorization map order 193 Additional resources 13 Administrative password, setting 130 Alarm thresholds, setting 53, 114 Appliance Setup menu 34 Appliance, connecting 30 Appliance, connecting your network 29 Appliance, navigating 32 Appliance, overview of 15 Appliances, registering 17 arp 181 Authentication, enabling 89 Auto-discovery rules, overview of 43 Auxiliary Interface, setting 83 B Bandwidth Optimization report 141 C
Fixed-target rules overview of 43 FTP proxies, setting 92 G Getting help 14 H Hardware and software dependencies 11 hardware ecc-mem-check enable 216 Help technical support 14 Help menu 34 Home menu 34 Host name, setting 76 hostname 178 HP storage web site 14 HP, contacting 14 I image boot 206 image delete 207 image fetch 207 image install 207 image move 208 In-path interfaces, modifying 79 rules, setting 42 static network routes, setting 85 Installing, prerequisites 22 Interactive ports, forwarded 220 Inte
tacacs-server timeout 198 tcpdump 214 Technical support 14 telnet 214 Throughput report 143 traceroute 214 U username nopassword 170 username password 170 username password 0 171 username password 7 171 Users, types of 9 INDEX S Secure ports, forwarded 220 Secure ports, forwarding traffic on 45 Secure-CIFs feature, enabling 46 Service, restarting appliance groups 99 Setup Manager menu 34 show arp 181 show bootvar 208 show cli 165 show clock 174 show configuration 204 show configuration files 204 show conf
INDEX