HP StorageWorks Enterprise File Services WAN Accelerator 2.1.5 deployment guide (June 2006)

ManualsBrandsHP ManualsComputer AccessoriesHP StorageWorks Enterprise File Services (EFS) DL320-1020 WAN Accelerator

HP STORAGEWORKS ENTERPRISE FILE SERVICES WAN ACCELERATOR 2.1.5 DEPLOYMENT GUIDE 61

6 - POLICY-BASED ROUTING

EPLOYMENTS

Right-SH > enable

Right-SH # configure terminal

Right-SH (config) # in-path enable

Right-SH (config) # in-path oop enable

Right-SH (config) # in-path cdp enable

Right-SH (config) # interface in-path ip address 10.1.3.2 /24

Right-SH (config) # ip in-path-gateway inpath0_0 10.1.3.1

Right-SH (config) # write memory

Right-SH (config) # restart

IMPORTANT: You must save your changes to memory and restart the HP EFS WAN

Accelerator service for your changes to take effect.

To configure the Cisco

router

1. On the left router, at the system prompt, enter the following commands:

TIP: Enter configuration commands, one per line; end with CTRL-Z.

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#interface fastEthernet 0/0.1

Router(config-subif)#encapsulation dot1Q 1

Router(config-subif)#ip address 10.0.1.1 255.255.0.0

Router(config-subif)#ip policy route-map TrafficToRightS

Router(config-subif)#exit

Router(config)#interface fastEthernet 0/0.2

Router(config-subif)#encapsulation dot1Q 2

Router(config-subif)#ip address 10.0.2.1 255.255.0.0

Router(config-subif)#ip policy route-map TrafficFromLeftS

Router(config-subif)#exit

Router(config)#interface fastEthernet 0/0.3

Router(config-subif)#encapsulation dot1Q 3

Router(config-subif)#ip address 10.0.3.1 255.255.0.0

Router(config-subif)#exit

Router(config)#interface fastEthernet 0/1

Router(config-subif)#ip address 10.0.4.1 255.255.0.0

Router(config-subif)#ip policy route-map TrafficToLeftSAndFromRightS

Router(config-subif)#exit

Router(config)#access-list 101 permit tcp any 10.1.2.0 0.0.0.255

Router(config)#access-list 102 permit tcp 10.0.2.0 0.0.0.255 any

Router(config)#access-list 103 permit tcp any 10.0.2.0 0.0.0.255

Router(config)#access-list 104 permit tcp 10.1.2.0 0.0.0.255 any

Router(config)#route-map TrafficToRightS permit 10

Router(config-route-map)#match ip address 101

Router(config-route-map)#set ip next-hop 10.0.3.2

Router(config-route-map)#set ip next-hop verify-availability

Router(config-route-map)#exit

Router(config)#route-map TrafficFromLeftS permit 10

Router(config-route-map)#match ip address 102

Router(config-route-map)#set ip next-hop 10.0.3.2

Router(config-route-map)#set ip next-hop verify-availability

Router(config-route-map)#exit

Router(config)#route-map TrafficToLeftS permit 10

Router(config-route-map)#match ip address 103 104

Router(config-route-map)#set ip next-hop 10.0.3.2

Router(config-route-map)#set ip next-hop verify-availability

Router(config-route-map)#end

Router#

2. On the right router, at the system prompt, enter the following set of commands: