HP StorageWorks Command Console V2.5 User Guide (AA-RV1UA-TE, March 2005)
Table Of Contents
- Contents
- About this Guide
- About SWCC
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
Using the Storage Window
80 Command Console V2.5 User Guide
Managing and Creating Spare Devices
Making a spare device part of a virtual disk lets you protect the integrity of the
RAID setup. A spare is especially important for virtual disks that have RAID
requirements of two or more devices. If one device fails, the virtual disk instantly
and automatically activates the spare device as a replacement.
A spare works as follows: if a device fails in a RAID 1, RAID 0+1, or RAID 3/5
virtual disk, the spare automatically replaces the failed device and the controller
reconstructs all virtual disks of which the failed device was a member.
After the controller writes data to a spare, the spare becomes part of the same
device group in which a device failed.
Creating a Spare Device
To create a spare device:
1. In the Storage window, click the device that you want to use as a spare. For an
automatic failed drive replacement, the device must be available and have a
capacity equal to or greater than the lowest capacity drive in the group.
2. From the Storage menu, choose Device, and then choose Make Spare.
Clearing Failed Devices
In the Storage window, the icon of a failed device is displayed with an X covering
it.
To clear the failed device:
1. From the Storage menu, choose Device.
2. Then choose Delete.