HP StorageWorks Command Console V2.5 User Guide (AA-RV1UA-TE, March 2005)
Table Of Contents
- Contents
- About this Guide
- About SWCC
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
Index
Command Console V2.5 User Guide 149
symbols on equipment 13
T
TCP/IP network 25
technical support, HP 16
Telocator Alphanumeric Protocol (TAP) 46
temperature 48, 83
text symbols 12
third-party storage management program 45,
54
Transmission Control Protocol/Internet Protocol
(TCP/IP) network 25, 31, 34, 40
traps 55, 111, 114
U
UNIX host 92
user profiles 46
V
VGA resolution 23, 67
virtual device 69
virtual disk 21
Command Console 106
creating 72
deleting 75
failure 48
icon 76
LUN address 71
maximum capacity 72
member 72, 76, 100
modifying 76
operating system configuration 77
preserving IDs 108
recovering data 100
state 115
status 67, 83
UNIX configuration 78
Windows NT/2000 configuration 77
W
warning
rack stability 15
symbols on equipment 13
web sites
HP storage 16
Wide Area Network (WAN) 26
Windows 2000/Windows NT 4.0
Asynchronous Event Service (AES) 42
disabling CCL 107
exception 25, 57, 93, 105
system configuration 94
Windows Internet Name Service (WINS) 25