HP StorageWorks Command Console V2.5 User Guide (AA-RV1UA-TE, March 2005)
Table Of Contents
- Contents
- About this Guide
- About SWCC
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
Using the Storage Window
72 Command Console V2.5 User Guide
Viewing Properties of the Battery
The Battery tab provides the following information:
■ The state of the battery
■ The expiration date of the battery
Creating Virtual Disks
You can use the Virtual Disk Wizard to create different types of logical storage
units (called virtual disks) on your subsystem.
You can create the following types of virtual disks:
■ Single-device virtual disks (JBODs)
■ Striped virtual disks (RAID 0)
■ Mirrored virtual disks (RAID 1)
■ Striped mirrored virtual disks (RAID 0+1)
■ Striped parity virtual disks with parity across all drives (RAID 3/5)
Note that the capacity of the smallest member, not the largest, determines the
maximum capacity of RAID-based virtual disks.
■ The maximum capacity of RAID 0 virtual disks is equal to the number of
members times the capacity of the smallest member.
■ The maximum capacity of RAID 1 virtual disks is equal to the capacity of the
smallest member.
■ The maximum capacity of RAID 0+1 virtual disks is equal to the number of
members in one stripe times the capacity of the smallest mirrorset member.
■ The maximum capacity of RAID 3/5 virtual disks is equal to the number of
members minus one times the capacity of the smallest member.
Before you can create virtual disks from a physical device, your controller must
know of the device. You can add devices online without restarting the controller.
This procedure describes how to add a physical device before you create a virtual
disk.
To add a physical device and then create a virtual disk, follow these steps:
1. From the Navigation window, open a Storage window within a desired
subsystem.
2. Click Storage > Device > Add in the Navigation window.