HP StorageWorks Command Console V2.5 User Guide (AA-RV1UA-TE, March 2005)
Table Of Contents
- Contents
- About this Guide
- About SWCC
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
About this Guide
Command Console V2.5 User Guide
11
In This Guide
This guide contains the following chapters and appendixes:
■ Chapter 1—”About SWCC” provides a description of the function and
capabilities of the SWCC application.
■ Chapter 2—”Using SWCC” provides instructions on how to use SWCC.
■ Chapter 3—”Setting Up Notification” provides instructions on how to set up
notifications on SWCC.
■ Chapter 4—”Interpreting Agent Email Messages” provides a description of
how to interpret Agent email messages.
■ Chapter 5—”Using the Storage Window” provides instructions on how to use
Storage windows.
■ Chapter 6—”Integrating SWCC with Insight Manager” provides instructions
on how to integrate SWCC with the Insight Manager.
■ Chapter 7—”Troubleshooting” provides instructions on how to troubleshoot
SWCC.
■ Appendix A—”Using the Command Console LUN” provides instructions on
how to use the SWCC LUN.
■ Appendix B—”Interpreting SNMP Traps” provides instructions on how to
interpret SNMP trap messages.