Using the HP DTC Manager/UX

Installing DTC Manager/UX with HP-UX 10.x

Note The following commands are for HP-UX version 10.30 (with four lan cards; lan0,

lan1, lan2 and lan3):

tail /var/adm/rbootd.log

Sat Jan 1 08:48:46 2000 : STARTUP

Sat Jan 1 08:48:46 2000 : ppa=0 Ether

Sat Jan 1 08:48:46 2000 : lan0: type: Ether NMID = 0

Sat Jan 1 08:48:46 2000 : ppa=1 Ether

Sat Jan 1 08:48:46 2000 : lan1: type: Ether NMID = 1

Sat Jan 1 08:48:46 2000 : ppa=2 Ether

Sat Jan 1 08:48:46 2000 : lan2: type: Ether NMID = 2

Sat Jan 1 08:48:46 2000 : ppa=3 Ether

Sat Jan 1 08:48:46 2000 : lan3: type: Ether NMID = 3

Sat Jan 1 08:48:46 2000 : matched lan0 : ppa 0

Sat Jan 1 08:48:46 2000 : matched lan1 : ppa 1

Sat Jan 1 08:48:46 2000 : matched lan2 : ppa 2

Sat Jan 1 08:48:46 2000 : matched lan3 : ppa 3

Sat Jan 1 08:48:46 2000 : got 4 lan device(s)

Sat Jan 1 08:48:47 2000 : INITIALIZATION COMPLETE

tail /var/opt/dtcmgr/log/dtcnmd.log

Sat Jan 1 08:48:55 2000 : STARTUP

Sat Jan 1 08:48:55 2000 : COUNT : 4

Sat Jan 1 08:48:55 2000 : ppa = 0

Sat Jan 1 08:48:55 2000 : type: Ether ‘lan0’; index= 0

Sat Jan 1 08:48:55 2000 : ppa = 1

Sat Jan 1 08:48:55 2000 : type: Ether ‘lan1’; index= 1

Sat Jan 1 08:48:55 2000 : ppa = 2

Sat Jan 1 08:48:55 2000 : type: Ether ‘lan2’; index= 2

Sat Jan 1 08:48:55 2000 : ppa = 3

Sat Jan 1 08:48:55 2000 : type: Ether ‘lan3’; index= 3

Sat Jan 1 08:48:55 2000 : found 4 supported rbootd interface(s):

Sat Jan 1 08:48:55 2000 : nmd_main : got 4 lan devices

Sat Jan 1 08:48:55 2000 : matched lan0 : ppa 0

Sat Jan 1 08:48:55 2000 : matched lan1 : ppa 1

Sat Jan 1 08:48:55 2000 : matched lan2 : ppa 2

Sat Jan 1 08:48:55 2000 : matched lan3 : ppa 3

Sat Jan 1 08:48:56 2000 : INITIALIZATION COMPLETE

These tail commands show you the last few lines of the log ﬁles. These log ﬁles

report whether the process is running. These log ﬁles also contain all the error

messages that might have occurred during start-up and running of the daemons.

3 If the log files indicate INITIALIZATION COMPLETE, you can now use the

DTC Manager/UX commands.

4 If you are upgrading from a previous release of DTC Manager/UX, reboot each

DTC by switching it off and then on (power off/on).

This completes the installation of the DTC Manager/UX. You can now use

DTC Manager/UX commands.