HP-UX vPars and Integrity VM V6.3 Administrator Guide

hpux-atc-sd2-001par1# ioscan -kfNC fc
Class I H/W Path Driver S/W State H/W Type Description
======= =============== ====== ========= =========
==============================================================
fc 1 41/0/2/0/0/0/0 fcd CLAIMED INTERFACE HP AH401A 8Gb Dual Port PCIe Fibre Channel Adapter
(FC Port 1)
fc 9 41/0/2/0/0/0/0.0x11 fcd CLAIMED INTERFACE HPVM Virtual FC (VFC) Controller
fc 2 41/0/2/0/0/0/1 fcd CLAIMED INTERFACE HP AH401A 8Gb Dual Port PCIe Fibre Channel Adapter
(FC Port 2)
fc 4 42/0/1/0/0/0/0 fcd SUSPENDED INTERFACE HP SN1000Q 16Gb Dual Port PCIe Fibre Channel Adapter
(FC Port 1)
fc 8 42/0/1/0/0/0/0.0x11 fcd SUSPENDED INTERFACE HPVM Virtual FC (VFC) Controller
fc 5 42/0/1/0/0/0/1 fcd SUSPENDED INTERFACE HP SN1000Q 16Gb Dual Port PCIe Fibre Channel Adapter
(FC Port 2)
And, the targets and LUNs impacted in dscvr_g01 are gone to NO_HW state.
dscvr_g01# ioscan -kfNH 0/0/0/0
Class I H/W Path Driver S/W State H/W Type Description
======== =============================================== ====== ========= =========
================================================
ext_bus 0 0/0/0/0 gvsd CLAIMED INTERFACE HPVM NPIV Stor Adapter
tgtpath 0 0/0/0/0.0x21530002ac000d2c estp NO_HW TGT_PATH Virtual Storage HBA
target served by gvsd driver,target port id 0x10200
lunpath 0 0/0/0/0.0x21530002ac000d2c.0x0 eslpt NO_HW LUN_PATH LUN path for ctl0
lunpath 1 0/0/0/0.0x21530002ac000d2c.0x4001000000000000 eslpt NO_HW LUN_PATH LUN path for disk0
After the IO card is replaced with a new one, the olrad -R command can be used to resume
usage of the card.
hpux-atc-sd2-001par1# olrad -R 10-0-1-1-0-5
Activity: Start of Post Replace
Target slot: 10-0-1-1-0-5
Activity: End of Post Replace
Target slot: 10-0-1-1-0-5
Activity: Target slot powered on, drivers resumed, OK to start using the card
Target slot: 10-0-1-1-0-5
At this point, the NPIV HBA and the targets and LUNs behind it are ready for use and come back
to the CLAIMED state.
dscvr_g01# ioscan -kfNH 0/0/0/0
dscvr_g01# ioscan -kfNH 0/0/0/0
Class I H/W Path Driver S/W State H/W Type Description
======== =============================================== ====== ========= =========
================================================
ext_bus 0 0/0/0/0 gvsd CLAIMED INTERFACE HPVM NPIV Stor Adapter
tgtpath 0 0/0/0/0.0x21530002ac000d2c estp CLAIMED TGT_PATH Virtual Storage HBA
target served by gvsd driver,target port id 0x10200
lunpath 0 0/0/0/0.0x21530002ac000d2c.0x0 eslpt CLAIMED LUN_PATH LUN path for ctl0
lunpath 1 0/0/0/0.0x21530002ac000d2c.0x4001000000000000 eslpt CLAIMED LUN_PATH LUN path for disk0
174 PCI OLR support on VSPs