HP-UX 11i v3 Installation and Update Guide HP Integrity Servers and HP 9000 Servers HP Part Number: 5992-5741 Published: September 2007, Edition 2.
© Copyright 2000-2008 Hewlett-Packard Development Company, L.P Legal Notices Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license.The information contained herein is subject to change without notice.
Table of Contents About This Document ....................................................................................................................9 Intended Audience...............................................................................................................9 Publishing History................................................................................................................9 Document Organization........................................................................
Mass Storage Stack for HP-UX 11i v3.................................................................................39 HP-UX 11i v3 Device Special File (DSF).............................................................................40 Security Considerations......................................................................................................41 Predefined Security Levels............................................................................................
Reviewing the Cold-Install Process....................................................................................69 Cold-installing HP-UX 11i v3.............................................................................................70 Before You Begin...........................................................................................................70 Miscellaneous Data Collection Table.......................................................................71 Network Data Collection Table...
8 Verifying System Install or Update............................................................................................113 Verifying the HP-UX Cold-Install or Update...................................................................114 Task 1: Listing all Software Installed on Your System.................................................114 Task 2: Verifying the Installed Software......................................................................114 Backing Up the System.........................
List of Figures 3-1 5-1 5-2 6-1 6-2 6-3 6-4 6-5 6-6 6-7 Install-time Security Software Dependencies.............................................................45 Cold-installing HP-UX 11i v3......................................................................................69 Software Tab ...............................................................................................................81 Updating to HP-UX 11i v3................................................................................
List of Tables 1 2 3 1-1 2-1 3-1 3-2 3-3 3-4 3-5 4-1 5-1 5-2 5-3 6-1 6-2 6-3 6-4 A-1 C-1 C-2 C-3 8 Publishing History Details............................................................................................9 Typographic Conventions...........................................................................................11 HP-UX 11i Releases.....................................................................................................12 HP-UX 11i v3 Operating Environments.................
About This Document This guide describes installing (called cold-installing) HP-UX 11i v3 (B.11.31) and updating from the following paths: • HP-UX 11i v2 (B.11.23) PA-RISC to HP-UX 11i v3 (B.11.31) PA-RISC • HP-UX 11i v2 (B.11.23) Intel Itanium® to HP-UX 11i v3 (B.11.31) Intel Itanium® The document printing date and part number indicate the document's current edition. The printing date will change when a new edition is printed. Minor changes may be made at reprint without changing the printing date.
Document Organization The HP-UX 11i v3 Installation and Update Guide is divided into chapters and appendixes, which contain information about installing and updating HP-UX 11i v3. IMPORTANT: The Read Before Installing or Updating to HP-UX 11i v3. DVD booklet that comes with the HP-UX 11i v3 media contains last-minute cold-install and update information that was not available when this guide was published. Make sure to review the booklet before continuing. • Chapter 1: “Welcome to HP-UX 11i v3” (page 17).
• Appendix A (page 117). Use this appendix to learn about the known problems and troubleshooting steps for the install and update. • Appendix B (page 131). Use this appendix to learn about the effect of two VxFS tunables, vx_ninode and vxfs_bc_bufhwm, on system memory consumption and learn about the guidelines on setting them for machines with relatively low RAM. • Appendix C (page 135). Use this appendix to learn about the OEs and media contents.
HP-UX Release Name and Release Identifier Each HP-UX 11i release has an associated release name and release identifier. The uname(1) command with the -r option returns the release identifier. Table 3 lists the releases available for HP-UX 11i. Table 3 HP-UX 11i Releases Release Identifier Release Name Supported Processor Architecture B.11.11 HP-UX 11i v1 PA-RISC B.11.23 HP-UX 11i v2 PA-RISC and Intel Itanium® B.11.
You can find the release notes in the following locations: — HP-UX Instant Information DVD. See “Media Kit Contents” (page 18) for more information. — The HP Technical Documentation Web site: http://docs.hp.com/ Here you will find the release notes pertinent to previous releases of HP-UX, as well as release notes for various individual products.
Other HP Web Resources The following Web sites provide a variety of information regarding the HP-UX 11i v3 release: • HP Integrity Servers: http://h20341.www2.hp.com/integrity/cache/332341-0-0-0-121.html • HP 9000 Servers: http://h20338.www2.hp.com/hpux11i/cache/324545-0-0-0-121.html • Itanium-based Server Information: http://h20338.www2.hp.com/hpux11i/cache/324923-0-0-0-121.html • HP Software Depot: http://www.hp.com/go/softwaredepot • HP Software Releases and Media: http://www.hp.
• International information: http://www.hp.com Select a country or region if you are not automatically directed. • Localized user guides: http://docs.hp.com Use the navigation menu to select a language. • Partition Manager http://www.docs.hp.com/en/PARMGR/ • Safety and ergonomic information: http://www.hp.com/ergo • HP Systems Insight Manager: http://www.hp.com/go/hpsim • Software Distributor: http://www.docs.hp.com/en/SD/ • System administration for HP-UX systems: http://docs.hp.
HP Encourages Your Comments HP encourages your comments concerning this document. We are truly committed to providing documentation that meets your needs. Please send comments to: http://docs.hp.com/en/feedback.html Please include document title, manufacturing part number, and any comment, error found, or suggestion for improvement you have concerning this document. Also, please include what we did right so we can incorporate it into other documents.
1 Welcome to HP-UX 11i v3 HP-UX 11i v3 is an enterprise release delivering the highest level of integrated virtualization and automation. HP-UX 11i v3 dynamically reduces complexity and cuts deployment times to maximize return on investment. The HP-UX 11i v3 release supports both HP Integrity servers and HP 9000 servers, including those based on dual-core Intel Itanium 2 processors. HP-UX 11i v3 is engineered to maintain compatibility with previous HP-UX 11i releases.
Media Kit Contents This guide is part of the HP-UX 11i v3 media kit, which includes the following DVDs and documents: • • • • HP-UX 11i v3 (B.11.31) DVD (2-DVD set) — Contains the HP-UX Operating System (OS), Operating Environments (OEs), required networking software, Update-UX, Ignite-UX, and online diagnostics. HP-UX 11i v3 (B.11.31) Applications DVD — Contains HP-UX application software. HP-UX 11i v3 Instant Information DVD — Contains HP-UX manuals, release notes, and white papers.
HP-UX 11i v3 Operating Environments Operating Environments (OEs) are tested and integrated application bundles designed to work with the operating system and provide the functionality needed for your system's purpose.
The Next Step Continue with Chapter 2: “System Requirements for Cold-Installing and Updating” (page 21).
2 System Requirements for Cold-Installing and Updating This chapter helps you assess the current state of your system prior to cold-installing or updating to HP-UX 11i v3.
System Requirements To cold-install or update HP-UX 11i v3, you must have the following: • • • A supported system. See “Supported Systems” (page 26) HP-UX 11i v3 OE and Application (AR) media 1.5 GB memory, minimum NOTE: The minimum memory limit is intended for running the HP-UX 11i v3 Foundation OE (FOE) and minimal applications. Additional memory will be required for optimal performance and optional software and applications.
Disk Space Requirements for a Cold-Install Table 2-1 lists the amount of disk space allocated for the indicated partitions during a default cold-install for each Operating Environment. Table 2-1 File Partition Disk Space Allocation by OE1, 2 Partition FOE EOE MCOE TCOE / 1 GB (28% used) 1 GB (29% used) 1 GB (29% used) 1 GB(28% used) /stand 1.9 GB (7% used) 1.9 GB (7% used) 1.9 GB (7% used) 1.9 GB (7% used) /var 8.5 GB (3% used) 8.5 GB (3% used) 8.5 GB (3% used) 8.5 GB (3% used) /usr 3.
Disk Space Allocation for File Partitions Depending on your system's purpose, you may need to determine how much disk space you will need for each file partition before you cold-install or update to HP-UX 11i v3. For example, if you plan to install applications from other vendors, you may need to modify the size of the /opt partition to accommodate their size. Depending on how much disk space is available, you can change the partition size to meet your needs.
How to Plan Your Disk Space Needs This section provides hints and information to help you determine your disk needs for HP-UX 11i v3. If you need more disk space, be sure to order the equipment and plan on installing it after backing up your current system. • • Record the hardware path to the DVD drive.
Supported Systems For a list of HP 9000 and HP Integrity systems that this release of HP-UX 11i v3 fully supports, refer to HP Server Support Matrix at the following website: http://www.hp.com/go/hpuxservermatrix NOTE: HP-UX 11i v3 is not supported on workstations. HP recommends that PA-RISC workstation users use HP-UX 11i v1, and Itanium®-based workstation users use HP-UX 11i v2. Further information about HP workstations can be found at the following website: http://hp.com/go/workstations.
Supported Network Drivers, Mass Storage Drivers, I/O Cards, and Storage Devices Before installing HP-UX 11i v3, make sure that the drivers, I/O cards, and storage devices on your system are supported. You can run the msv2v3check script to validate whether the drivers, mass storage I/O cards, and mass storage devices installed on your system are supported on HP-UX 11i v3. This script will report if any unsupported drivers, mass storage I/O cards, and mass storage devices are found on your system.
http://www.hp.com/products1/serverconnectivity/mass_storage_devices.html WARNING! If third-party (non-HP) storage will be connected to your HP-UX 11i v3 system, HP recommends that you contact your third-party storage vendor to determine the compatibility of the storage with HP-UX 11i v3. Check with your third-party storage vendor for information about any pre-requisites and limitations with the storage on HP-UX 11i v3.
Identification of Model, OS/OE, and Software Before you cold-install or update to HP-UX 11i v3, you need to identify the model of your system and other information. Identifying the Model To determine the model number of your system, enter: model To verify that HP-UX 11i v3 is supported on your system, see “Supported Systems” (page 26).
Identifying Installed Software To identify the software products on a system or media, use swlist.
3 Choosing an Installation Method This chapter provides information and scenarios to help you choose the most appropriate method to install HP-UX 11i v3 on your system.
Cold-Installs of HP-UX 11i v3 Cold-install means installing system software on a new (uninstalled) or existing system by completely rebuilding the root volume group, erasing the existing operating system and data on that volume, and installing the new operating system and specified software and data.
Supported Update Paths to HP-UX 11i v3 Update means using update-ux to selectively overwrite the operating system and application software from a media or network source depot. An advantage of performing an update is that it leaves user data, configuration, and applications in place. You can update to HP-UX 11i v3 from HP-UX 11i v2 (B.11.23). Updating from any other release directly to HP-UX 11i v3 is not supported.
Updating from HP-UX 11i v2 (B.11.23) Table 3-1 lists the supported update paths from HP-UX 11i v2 to the HP-UX 11i v3.
Deciding Which Method to Use Now that you have evaluated your system and ordered any needed hardware, you need to decide whether to cold-install or update to HP-UX 11i v3 on your system. When to Cold-Install CAUTION: The cold-install process erases software on the root volume before installing. If you want to retain any existing software, make sure to back up that software before migrating or use update.Cold-installing using Ignite-UX overwrites everything on the target volume.
• • Each system has a unique configuration. Current disk space is sufficient for HP-UX 11i v3. See “How to Plan Your Disk Space Needs” (page 25). You can choose two different methods to update to HP-UX 11i v3 on a supported system: 1) by the using the update-ux terminal user interface; 2) by using the update-ux command line interface. An advantage of performing an update is that it leaves user data, configuration, and applications in place.
system for installing many similar systems. The process described in this guide cold-installs and updates a single system from local media. • If you are cold-installing or updating one system at a time — Cold-install or update directly from the DVDs in the HP-UX 11i v3 media kit: — HP-UX 11i v3 OE media — Boot and install a new system or update an existing system. — HP-UX Application media— Install applications not installed with the OE or install a newer version of an OE application.
2007 release or later cannot be supported, due to known problems with the initial release of 11.31 HP-UX software management tools (that get installed with OE bundles from February 2007).
Mass Storage Stack for HP-UX 11i v3 HP-UX 11i v3 introduces a new representation of mass storage devices, known as the agile view. In the agile view, disk devices and tape drives are identified by the actual object, not by a hardware path to the object. In addition, paths to the device can change dynamically and multiple paths to a single device can be transparently treated as a single virtualized path, with I/O being distributed across those multiple paths.
HP-UX 11i v3 Device Special File (DSF) In a similar way to hardware paths, there are two types of DSFs for mass storage: legacy DSFs and persistent DSFs. Both can be used to access a given mass storage device independently, and can coexist on a given system. These DSFs are described below. • • A legacy device special file was the only type of mass storage DSF in releases prior to HP-UX 11i v3, so it is associated with the legacy view.
Security Considerations HP-UX Bastille (HPUXBastille) is included as recommended software on the Operating Environment media and can be installed and run with Ignite-UX or Update-UX, (see “Predefined Security Levels” (page 41)). HP-UX Bastille is a security hardening and lockdown tool that can be used to enhance security of the HP-UX operating system. It provides customized lockdown on a system-by-system basis by encoding functionality similar to Bastion Host and other hardening and lockdown checklists.
Selecting Your Security Levels at Install Time During installation, you can configure your security levels by navigating to the System tab from the Ignite-UX Graphical User Interface Installation and Configuration dialog box. The System tab allows you to configure information unique to your system such as security levels, hostname, IP address, root password, and the time zone. For ease of use, HP recommends using the System tab to select the security level appropriate for your deployment as described below.
Serviceguard Configuration (post-installation) to Enable Use with Security Levels Configuring Sec20MngDMZ or Sec30DMZ for Use with Serviceguard Serviceguard uses dynamic ports. To enable operation, the possible-SG port range must be opened. Opening the port range is not consistent with the security goals of Sec20MngDMZ (MANDMZ.config) and Sec30DMZ (DMZ.config) since multiple services (including other rpc-like applications), may also listen to this same port range.
Configuring HP-UX Bastille Sec10Host To configure the HP-UX Bastille Sec10 Host, refer to the Securing Serviceguard document at: http://docs.hp.com/ CAUTION: When reverting to the configuration prior to the use of HP-UX Bastille, note these precautions: • Security configuration changes will be undone temporarily. • Other manual configuration changes or additional software installed since HP-UX Bastille was initially run may result in HP-UX Bastille requiring a manual merge of configuration settings.
Security Choice Dependencies The Sec00Tools security level is installed by default on your system. Although Sec00Tools does not implement any security changes at cold-install- or update-time, it does ensure that the required software (Figure 3-1) is installed. The Sec00Tools security level contains the pre-built configuration files that you can use to create a security level or you can use it as a template to create a custom security configuration.
Secured Services and Protocols Each security level provides incrementally higher security by locking down various protocols and services. HP-UX Bastille uses a series of questions to determine which services and protocols to secure. Using one of the security levels applies a default security profile, simplifying the lockdown process.
Table 3-3 Host-based Sec10Host Install-time Security Settings (continued) Category Actions Daemons Disable ptydaemon Disable pwgrd Disable rbootd Disable NFS client daemons Disable NFS server Disable NIS client programs Disable NIS server programs Disable SNMPD inetd Services Deactivate bootp Deactivate inetd's built-in services Deactivate CDE helper services Deactivate finger Deactivate ident Deactivate klogin and kshell Deactivate ntalk Deactivate login, shell, and exec services Deactivate swat Deact
Table 3-4 Additional Sec20MngDMZ Install-time Security Settings1 Category Actions inetd Services Includes all disabled inetdservices in Table 3-3 and: Deactivate ftp Deactivate telnet Restrict syslog daemon to local connections IPFilter Configuration2 1 2 3 4 5 Block incoming DNS query connections Block incoming HIDS administration connections3,4 Configure IPFilter to allow outbound traffic, block incoming traffic with IP options set, and all other traffic except for HP-UX Secure Shell, HIDS agent, WB
Online Diagnostics The diagnostics software, which is installed with HP-UX 11i v3, consists of two product bundles: • OnlineDiag • SysFaultMgmt These bundles include many tools to help verify, troubleshoot, and monitor PA-RISC and Itanium-based system hardware such as processors, memory, power supplies, fans, interface cards and mass storage devices.
The SysFaultMgmt bundle includes the System Fault Management (SFM) software. The SFM software includes the following tools: • SFM Providers SFM monitors the health of HP servers and retrieves information about hardware such as memory, processors, power supplies, and cooling devices. SFM operates in the Web-based Enterprise Management (WBEM) environment. • EVWEB EVWEB is packaged with SFM and can be used to view and administer WBEM indications generated on the HP-UX 11i v3 system.
Offline Diagnostics Offline Diagnostic Environment (ODE) includes a set of offline support tools that enables you to troubleshoot a system that is running without an operating system. ODE is available on the following media: • • HP 9000 PA-RISC Offline Diagnostics CD, for PA-RISC systems. HP Itanium-Processor Family (IPF) Offline Diagnostics and Utilities CD, for Itanium-based systems. HP highly recommends that you get the latest CD and update the Offline Diagnostics for improved functionality.
4 Preparing to Cold-Install or Update to HP-UX 11i v3 This chapter details the preparation tasks required to cold-install or update to HP-UX 11i v3. What You Will Find in This Chapter • “Cold-Install Tasks” (page 54) • “Update Tasks” (page 60) • “Backing Up Your System” (page 62) • “Locating Source Media and Codewords” (page 65) • “The Next Step” (page 66) Time Estimate for This Chapter: Approximately 2 hours to gather the information needed and perform the prescribed tasks.
Cold-Install Tasks Prior to cold-installing HP-UX 11i v3, perform these tasks: • Select an HP-UX Console (Itanium-based systems only), if appropriate. • Back up any configuration files you want to reinstall. • Make a recovery image of your system. • If you intend to use Ignite-UX to cold-install HP-UX 11i v3 on more than one system, update your Ignite-UX server. For more information, refer to the Ignite-UX Administration Guide at: http://docs.hp.com/en/oshpux11iv3.html • Locate source media and codewords.
Determining if the conconfig Command Exists on your System 1. At the EFI prompt type the following command: Shell> conconfig • If the command exists, the system will return output similar to the following: CONSOLE CONFIGURATION Index Primary Type 1 P Serial 2 S VGA • 2. Device Path Acpi(HWP0002,PNP0A03,0)/Pci(1|2) Acpi(HWP0002,PNP0A03,0)/Pci(4|0) If the command does not exist, the system will return the error message: conconfig not found.
Using the Firmware Selection Menu to Select the Primary HP-UX Console 1. Decide what console you want to use. Depending on your system configuration, HP-UX can use one of the following devices as your system console: • • • 2. System Serial Port Management Processor (MP) Serial Port (if present) VGA device (if present) Using the EFI menus, do the following: • Select Boot option maintenance from the main Boot Manager Menu. • Select Select Active Console Output Devices.
Understanding Interface Differences Between Itanium-based Systems Each Itanium-based system has a similar interface with minor differences. You can navigate these menus with the arrow keys or v and ^ keys, and use the Enter or spacebar key to select and deselect devices. Selected devices have an asterisk (*) next to them. After making your changes to this menu, select Save Settings to NVRAM and then Exit.
Additional Notes on Console Selection • • • HP-UX acts based upon the EFI Boot Maintenance Manager menu's Select Active Console sections to determine where to send its output. If the incorrect console devices are selected, HP-UX may either fail to boot or boot with output directed to the wrong location. Therefore, any time new potential console devices are added to a system, or anytime NVRAM on a system is cleared, review console selections to ensure that they are correct.
Task 3: Making a Recovery Image of Your System Any data on the client disks that are used for installation, including the operating system, are removed entirely as part of this installation process. Make a recovery image of your system so you can easily restore it to its original state if a problem occurs. See “Backing Up Your System” (page 62) for more information. Task 4: Updating Your Ignite-UX Server Ignite-UX supports network-based installations, which might be convenient when installing many systems.
Update Tasks Prior to updating to HP-UX 11i v3, perform these tasks: • Identify all software products and bundles on your system. • Rebuild the HP-UX kernel. • Rename your log files to make it easier to find problems encountered during an update. • Back up your operating system using the Ignite-UX make_net_recovery or make_tape_recovery command. • Locate source media and codewords. Task 1: Identifying Software Versions 1.
Task 4: Backing Up Your System Back up your system before performing an update, and again after the update is complete. If a problem occurs, you can easily restore the system to its original state. See “Backing Up Your System” (page 62) for more information. Task 5: Locating Source Media and Codewords Locate the source media needed for the update. See “Locating Source Media and Codewords” (page 65) for instructions.
Backing Up Your System Back up your system before performing a cold-install or update, and again after the cold-install or update. If a problem occurs, you can easily restore the system to its original state.
For more information on using make_net_recovery, refer to the make_net_recovery(1M) manpage or the Ignite-UX Administration Guide. The guide is available at the HP Technical Documentation Web site: http://docs.hp.com/en/oshpux11iv3.html You can also locate the Ignite-UX Administration Guide at the Ignite-UX Information Library: http://www.docs.hp.com/en/IUX/infolib.
Task 2: Backing Up Your Data Files There are a number of different backup methods you may wish to choose from depending on your system backup needs and your configurations. Some recommended backup methods are: • • HP OpenView Storage Data Protector HP-UX fbackup/frecover utilities Choosing HP Storage Data Protector for Backup If you are backing up large numbers of systems, the HP Storage Data Protector software product can be particularly useful.
Locating Source Media and Codewords Now that you have backed up your system and important data files, locate the source media needed for the cold-install or update. See the section called, “Media Kit Contents” (page 18) for more information. You can obtain a codeword for a purchased product by contacting one of the HP licensing services in Table 4-1: Table 4-1 HP Licensing Services Location Telephone Email Asia 0120.42.1231 (Inside Japan) sw_codeword@hp.com 0426.48.9310 (Inside Japan) +81.426.48.
The Next Step You are now ready to cold-install or update to HP-UX 11i v3. • • 66 To cold-install: see Chapter 5: “Cold-Installing HP-UX 11i v3 From Media” (page 67). To update: see Chapter 6: “Updating to HP-UX 11i v3” (page 87).
5 Cold-Installing HP-UX 11i v3 From Media This chapter describes cold-installing HP-UX 11i v3. What You Will Find in This Chapter • “Before You Begin” (page 68) • “Reviewing the Cold-Install Process” (page 69) • “Cold-installing HP-UX 11i v3” (page 70) • “Post-Install Tasks ” (page 85) • “The Next Step” (page 86) Time Estimate for This Chapter: Approximately 2-3 hours, depending on your system.
Before You Begin Before you cold-install HP-UX 11i v3, make sure that: • • • 68 Your system meets the system requirements to install and operate HP-UX 11i v3. For more details see Chapter 2: “System Requirements for Cold-Installing and Updating” (page 21). You have completed the preparation tasks required to cold-install your system. Most importantly, make sure you created an operating system recovery image to protect your data in the event of a system crash.
Reviewing the Cold-Install Process Figure 5-1 (page 69) shows the overall process of cold-installing HP-UX 11i v3 from media. You can also cold-install HP-UX 11i v3 from network depots and from golden images. For more information on these alternative methods of cold-installing refer to the Ignite-UX Administration Guide. NOTE: If your system is on HP Mission Critical Support, discuss the proper installation method with your HP Customer Engineer.
Cold-installing HP-UX 11i v3 This section describes cold-installing from the HP-UX 11i v3 DVDs. Before you begin, review Appendix A (page 117) for any installation issues that apply to your system.
NOTE: During an installation, Ignite-UX configures the root, dump, and swap devices with the new HP-UX 11i v3 mass storage stack agile addressing representation. This means that, after installing, the commands that display the boot, dump, and swap devices will show them using the agile form. During a cold-install of HP-UX 11i v3, both legacy and persistent DSFs are automatically created.
Network Data Collection Table Table 5-2 provides HP-UX commands that you can use after the install to confirm specific information. Table 5-2 Network Data Type of Data 72 Your Specific Data HP-UX Command to Confirm Data After System is Up and Running Host Name uname -n/hostname Host IP Address nslookup hostname Subnet Mask grep SUBNET_MASK /etc/rc.config.d/netconf Default Gateway IP Address grep ROUTE_GATEWAY /etc/rc.config.d/netconf Domain Name cat /etc/resolv.
Task 1: Booting Your Machine This task describes how to boot your system from the install media. If you want to boot an Itanium-based system, follow the instructions in the section called, Booting Your Itanium-based System below. If you want to boot a PA-RISC system, follow the instructions in “Booting Your PA-RISC System” (page 74). Booting Your Itanium-based System 1. 2. 3.
Booting Your PA-RISC System 1. 2. 3. Make sure any external devices that need to be configured at cold-install are connected to the target system and are turned on and operational. Insert the HP-UX 11i v3 DVD into the drive. Stop the autoboot by pressing any key. The boot console menu is displayed. If you need help, enter: HELP 4. Ensure that Fast Boot is enabled. 1. Select the Configuration Menu: CO 2. If the Fast Boot selection is available, switch Fast Boot ON: FB ON 3.
For an agile hardware path, boot from the DVD drive using the full agile hardware path name: BOOT For more information on agile hardware paths, refer to the white paper called, The Next Generation Mass Storage Stack: HP-UX 11i v3 at the HP Technical Documentation Web site: http://docs.hp.com/ 7. After a few minutes, at the Interact with IPL? prompt press n. The install kernel loads (3-5 minutes), after which a screen might prompt you to enter the keyboard language of your console. 8.
Task 2: Selecting Your Installation Type The system displays the Ignite-UX welcome screen for the HP-UX installation process. When the initial Ignite-UX welcome screen appears, read how to navigate and select choices on this terminal interface: • • • • Use the Tab key to navigate between fields and the arrow keys to navigate within fields. Use the Enter key to select an item. Pressing Enter or the spacebar opens a menu list.
3. From the User Interface and Media Options window, choose the degree of customizing needed to configure the installation. Mark your choices and select OK. • Select from one of the three choices shown in Source Location Options: — Media only installation is the default setting for installing from a DVD. — Media with network enabled is recommended when you want basic networking enabled during installation so you can load software from a network depot (when an Ignite-UX server is not available).
Task 3: Configuring Your Installation At this point, the system displays the Install HP-UX Wizard screen for the HP-UX installation process. You are now at the first step of the Install HP-UX Wizard. This section describes how to configure your installation using the Guided Installation process. 1. 2. From the Install HP-UX Wizard screen, select an overall system configuration. Press Next to accept the default option, HP-UX B.11.31 Default. The system displays the System Environmentscreen.
NOTE: If you select VxVM or LVM, the root disk cannot be moved to another SCSI bus or address that results in a change in the hardware path to the device. If it is moved, you may not be able to boot safely from it. This is similar to the limitation present in LVM. 6. On the Root Disk/Volume Group Disks screen, s pecify how many disks you want placed into the root volume group. If you have more than one disk, you may select Yes to choose the Striping option.
9. On the Security Choices screen, select the appropriate security setting for your system based on the information in the section called, “Security Considerations” (page 41). Please note that four security levels are displayed. By default, Sec00Tools is selected. Press Next to accept your selection and proceed to the Pre-Install Disk Information screen. 10. On the Pre-Install Disk Information screen, identify which disks will be overwritten during the install process.
Task 4: Selecting and Deselecting Software Bundles If you use the Guided Installation or Advanced Installations, then you can deselect the software bundles that are installed by default and select optional software not installed by default. From the Software tab you can select products from a list of categories to build your operating system. (If you choose the No User Interface option, then you cannot deselect the default-installed software bundles.
Table 5-3 HP-UX 11i v3 Software Product Categories Software Category Description CompilersDevelopment Compilers and Development Tools CoreOS Core HP-UX Functionality Desktop Desktop Environments DisksFileSystems File Systems and Volume Mgmt Drivers I/O Drivers HighAvailability High Availability InetServices Internet Services Internet Internet Software Tools Interoperability Computing Interoperability Tools Java Java Tools and Utilities Localization Localization Manuals HP-UX Manual
• • • OE Required: Software that is required and is always installed with the operating system. Software in this category cannot be deselected. OE Recommended: Software that is recommended and should be installed because it fulfills the required software dependencies, if any exist. Software in this category can be deselected. OE Optional: Software that does not have to be installed.You can choose to select the desired software bundles prior to installing your system.
Task 5: Finishing Your Installation Finishing the Guided Installation process begins with filesets being copied from the media to the hard disk. The system automatically reboots during the installation process. Depending on how you set up your parameters, the system either sets basic network configurations automatically, or calls the set_parms command after it has rebooted to enable you to set the root password, date and time, time zone, IP address, and additional network parameters.
Post-Install Tasks Task 1: Configuring OE Applications After updating to an HP-UX 11i v3 Operating Environment (OE), some OE products need post-installation configuration to make them functional. This need may be indicated by a message logged in /var/opt/swm/swm.log. Refer to each product's installation instructions for details.
Create a New Root Home Directory Consider creating a root home directory that is not /. Doing this keeps the user root dot files out of the /directory. Make sure it is on the root volume by calling it something like /homeroot. Doing this is especially important if you are using Logical Volume Manager (LVM) and /home is a separate volume. 1. 2. 3. Log in as root. Except on trusted systems, edit /etc/passwd to change the home directory from root to /homeroot and save it.
6 Updating to HP-UX 11i v3 This chapter describes updating your system to HP-UX 11i v3 using Update-UX.
Before You Begin Before you update to HP-UX 11i v3, make sure that: • • • You are updating from a supported migration path. See “Supported Update Paths to HP-UX 11i v3” (page 33). Your system meets the system requirements to update and operate HP-UX 11i v3. For more details see Chapter 2: “System Requirements for Cold-Installing and Updating” (page 21). You have completed the preparation tasks required to update your system.
NOTE: If your system is on HP Mission Critical Support, discuss the proper method of installing the OE with your HP Customer Engineer. IMPORTANT: You must install the latest version of Update-UX prior to updating your system. The latest version of Update-UX allows you to use the preview (-p) option, which is new for HP-UX 11i v3. Failure to install the latest version of Update-UX may cause the update to fail. For instructions, see “Task 2: Install the Latest Update-UX Bundle” (page 92).
Table 6-1 Updating Tips Topic Tip Running Other Commands During the update process, be careful when running other commands; doing so may cause the commands to function improperly. All Software Does Not Get Updated Update-UX updates the HP-UX OS and any software specified in additional software bundles available on the source media or depot. Update-UX may not automatically update software that is not contained in an Operating Environment.
NOTE: In HP-UX 11i v3, there are two types of DSFs for mass storage: legacy DSFs and persistent DSFs. Both can be used to access a given mass storage device independently and can coexist on a given system. During an update from HP-UX 11i v2 to 11i v3, existing legacy DSFs are retained and persistent DSFs will be created. Configuration files will not be modified, so system devices will continue to use the existing legacy DSFs.
5. Mount the first DVD onto the new directory as a file system, for example: mount /dev/dsk/c1t2d0 /dvdrom 6. Create the directory that will contain the network depot you want to create, for example: mkdir /var/11iv3 7. Copy all products on the mounted DVD to the target depot. For example, to copy the contents of the first DVD to the target depot called update-depot type the following command: swcopy -s /dvdrom \ * @ /var/11iv3/update-depot 8.
2. Create the directory under root(/). For example: mkdir /dvdrom 3. Mount the DVD onto the new directory as a file system. For example: mount /dev/dsk/c1t2d0 /dvdrom 4. Using swinstall, install the latest version of the Update-UX bundle on the target system. NOTE: Make sure you use the correct case to install the Update-UX bundle (in title case). This bundle contains the update-ux command (lowercase).
Table 6-2 TUI update-ux Steps 1. Start-Up Start the update-ux TUI. 2. Select Source Provide the location of the software depot from which the software will be installed. 3. Select OE Select the OE that you wish to update to. 4. Select Software Choose the software in the OE you selected to update. 5. Analysis (Preview) Analyze (preview) the update selections to determine if the selected software can be updated successfully. 6. Update Perform the actual software update. 7.
Figure 6-2 Overview Screen 2. After reviewing the information on the Update-UX Overview tab, type n (next) to proceed to the Source Selection tab. Step 2: Select Source The Source Selection tab appears. The Source Selection tab displays a list of registered source depots on the local host system.
Figure 6-3 Select Source Tab 1. Specify the source depot that contains the new OE that you want to use to update your target system. The system automatically selects the local host and default depot path. You can expand any entry that is preceded by the + sign. This allows you to view the available depots on the server. 2.
Step 3: Select OE The OE Selection tab appears. An Operating Environment (OE) is an integrated set of software that contains the HP-UX operating system, and selected applications. The OE Selection tab displays the list of OEs to which you can update. The OE that matches the one currently installed on your system is automatically selected. You may choose a different OE by selecting it (which will automatically deselect the other). Figure 6-4 OE Selection Tab 1.
• • 2. included in this category. You may need to install additional drivers to use all hardware components. Software in this category cannot be deselected. Recommended: Software bundles that HP recommends you install because it fulfills software dependencies, if any exist. You can, however, manually de-select the bundles before you install or update your system. Optional: Software bundles that are not installed or updated by default.
Figure 6-5 Software Selection Tab CAUTION: HP recommends that you do not deselect recommended software bundles or remove them from your system unless you know for certain that the software contained in these bundles is not required for your operating environment. If you deselect recommended software during the update, the old version of the software you deselected will remain on your system. The old version may or may not be compatible with the newly updated HP-UX 11i v3 operating system.
• • • • • 2. E an error has occurred when selecting this item . has no status; is not selected or installed N is newer than the software on the system O is older than the software on the system I is currently installed on the system. After selecting the software you wish to install, type p (preview) to preview the actions that will occur for the update without modifying the system. The output window appears and begins displaying messages beginning with: Analyzing software to be installed.
1. 2. 3. If you started a preview session, the preview stops after the analysis. Press Enter to return to the Software Selection tab. After returning to the Software Selection tab, type l (log) to view the log file, which presents a view of detailed install information. Review any errors, warnings, or notes. Warnings are simply informational. If there are any errors, they will need to be resolved before the update can continue. Step 6: Update In this step, the system proceeds with the actual update.
Figure 6-7 Log Screen This log screen provides multiple ways of viewing the information recorded in the log file. You can filter out the messages by verbosity levels, using the action keys at the bottom of the screen. Table 6-3 “Log Files Generated During Update” lists the log files that are generated during an update: Table 6-3 Log Files Generated During Update 102 Log File Description /var/opt/swm/swm.
Table 6-3 Log Files Generated During Update (continued) Log File Description /var/adm/sw/swagent.log This log file contains the detailed output from the software installation, including control scripts that run during the update. Please note that the swm.log file is a superset of the information found in the swagent.log file. /var/adm/sw/swagentd.log These are log files for individual commands that run during the update. Success or failure and output from these commands is recorded in the swm.log.
Table 6-4 Update-UX Commands (continued) Update-UX Command Description -x option=value Specifies -x options to be applied during the update. For a typical update, no -x options are required. For information on -x options, refer to the swm (1M) manpage or the Software Distributor Administration Guide. sw_spec Software selections support the same syntax as the swinstall command plus the syntax described in the selection syntax section below.
NOTE: Make sure you install all new optional software included in the OE collection that you want at the same time that you do your update. Updating Optional Software From the Command Line To update to HP-UX 11i v3 and specify additional optional software bundles on the command line, follow these steps: 1. If you want to install additional optional software included with the HP-UX 11i v3 Foundation OE collection, enter: /usr/sbin/update-ux -s /dvdrom HPUX11-OE 2.
Stack: HP-UX 11i v3 and the white paper called HP-UX 11i v3 Persistent DSF Migration Guide at: http://docs.hp.com/ The Next Step Continue with the Chapter 7: “Installing HP Applications and Patches” (page 107).
7 Installing HP Applications and Patches This chapter describes how to install HP applications from the Application Software DVD, and provides references for patching and patch management. Before you begin, make sure you have already completed installing or updating HP-UX.
Installing HP-UX Applications Your HP-UX 11i v3 media kit contains the HP-UX Application Software DVD. The Application Software DVD has optional development tools and system management software that you can choose to install new or update the existing software on your system. TIP: You can find the complete list of applications included in the HP-UX 11i v3 release on the HP Software Releases & Media site: http://www.hp.com/softwarereleases/releases-media2/index.
Installing HP-UX Applications from the DVD Before you begin, review Appendix A (page 117) for any installation issues that apply to your system. Required Media Have the HP-UX 11i v3 Application Software DVD ready from the HP-UX 11i v3 media kit. You must boot HP-UX 11i v3 to install HP-UX application software products. Use the following procedure to install products from the Application Software DVD: 1. 2. Insert the Application Software DVD in the DVD drive. Mount the Application Software DVD.
5. Unmount and eject the Application Software DVD. You must unmount the DVD before you can eject it from the DVD drive. The DVD is automatically unmounted whenever the server reboots. Use the umount command to unmount the DVD. For example, umount /dvdrom unmounts the /dvdrom file system. Refer to the umount (1M) manpage for details. NOTE: After you install or update HP-UX 11i v3, the latest critical patches that shipped with the media are installed on your system.
HP-UX Software Assistant HP-UX Software Assistant (SWA) is a command-line based tool that consolidates and simplifies patch management and security bulletin management on HP-UX systems. The SWA tool is new for HP-UX releases as of January 2007. It includes Security Patch Check (SPC) and is the HP-recommended utility to use to maintain currency with HP-published security bulletins for HP-UX software. The bundle name is SwAssistant. The product number is B6834AA.
The Next Step Continue with Chapter 8: “Verifying System Install or Update” (page 113).
8 Verifying System Install or Update This chapter provides steps to verify that your system is ready and back in production. Before you begin, make sure you have already completed either cold-installing or updating to HP-UX 11i v3.
Verifying the HP-UX Cold-Install or Update To verify that HP-UX 11i v3 was installed or updated successfully, use the Software Distributor commands swlist and swverify, as described in this section. In addition, you can view the results of your update in the log file /var/opt/swm/swm.log. Refer to “Step 6: Update” (page 101) for more information.
The Next Step Now that you have installed or updated your system and have all the HP applications that you need, you may want to configure additional hardware or file systems. You can find many configuration tasks in HP-UX System Administrator's Guide. The guide is available at the HP Technical Documentation Web site: http://docs.hp.com/en/oshpux11iv3.
A Known Problems and Troubleshooting This appendix lists known problems and troubleshooting steps for the install and update. What You Will Find in This Appendix • “Known Install and Update Problems” (page 118) • “Uninstalling HP-UX 11i v3” (page 129) NOTE: While the HP-UX 11i v3 install progresses, messages are displayed relating to the progress being entered into the log file. These messages usually refer to normal behavior.
Known Install and Update Problems Table A-1 describes problems known to occur in the HP-UX 11i v3 release. Table A-1 Known Install and Update Problems Problem Description/Action Use latest version of Ignite-UX The Software Manager (swm) product used with the Ignite-UX and and Update-UX to install HP-UX Update-UX tools from the HP-UX 11i v3 February 2007 OE release patches may fail to select or configure all HP-UX 11i v3 September 2007 patches.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Patches May Not Install Correctly when using the HP-UX 11i v3 February 2007 version of Ignite-UX and Update-UX If you are using the HP-UX 11i v3 February 2007 version of either Ignite-UX or Update-UX to cold-install or update a system with a source depot that contains HP-UX 11i v3 with September 2007 patches, some patches may not install correctly.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Patches May Not be Configured when using the HP-UX 11i v3 February 2007 version of Ignite-UX and Update-UX If you are using the HP-UX 11i v3 February 2007 version of either Ignite-UX or Update-UX to cold-install or update a system with a source depot that contains HP-UX 11i v3 with September 2007 patches, certain patches may not be configured. What To Do The following is an example of /var/adm/sw/swagent.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Install PHCO_36356 to avoid failure with FC card Critical Resource Analysis (CRA) may unexpectedly fail during Online Replacement (OLR), Online Deletion (OLD), or dynamic unload of a Fibre Channel driver module. OLR occurs when doing a replacement operation with either the olrad command, PCI attention button, or the Systems Management Homepage (SMH) on systems with this OLR feature.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action HP Service Control Manager (SCM) not supported on HP-UX 11i v3 The HP Service Control Manager (HP SCM) is not supported on HP-UX 11i v3. If your system is running SCM, you must migrate to HP System Insight Manager (HP SIM) version 4.2 BEFORE updating to HP-UX 11iv3; otherwise the update may fail. What To Do Remove HP SCM before updating to HP-UX 11iv3.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Secure Path not supported on HP-UX 11i v3 Secure Path is not supported on HP-UX 11i v3.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action JavaOOB Installation Errors Updating from the HP-UX 11i v2 September 2006 release to the HP-UX 11i v3 September 2007 release may cause the following errors to appear in the console log, dmesg.log and syslog from the Java Out-of-Box (JavaOOB) installation: ERROR: The proposed values for nfile (4097) and maxfiles_lim (4096)do not meet t he constraint of (nfile >= (2 * maxfiles_lim)).
Table A-1 Known Install and Update Problems (continued) Problem Description/Action NFS*MAN filesets Produce swverify Errors During Install/Update or Removal After an HP-UX 11i v3 install/update, the swverify command may report that one or more of the following ONCplus.NFS manpage files is missing: /usr/share/man/man1m.Z/portmap.1m /usr/share/man/man1m.Z/umount_nfs.1 /usr/share/man/ja_JP.eucJP/man1m.Z/umount_nfs.1m /usr/share/man/ja_JP.SJIS/man1m.Z/umount_nfs.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Updating to HP-UX 11i v3 from HP-UX 11iv2 with VxFS 5.0 If VxFS 5.0 has been used to create file systems with disk layout version 7, those disks will not be readable by the VxFS 4.1 for HP-UX 11i v3. What To Do Make sure you copy data from your DLV 7 file systems onto file systems created at layout version 5 or 6 before updating to HP-UX 11iv3. Updating to HP-UX 11i v3 from HP-UX 11iv2 with VxFS 4.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Third-Party Storage If third-party (non-HP) storage will be connected to your HP-UX 11i v3 system, HP recommends that you contact your third-party storage vendor to determine the compatibility of the storage with HP-UX 11i v3. Check with your third-party storage vendor for information about any pre-requisites and limitations with the storage on HP-UX 11i v3.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action /dev/random or /dev/urandom Errors During Update When updating your system to HP-UX 11i v3, you may encounter the following error message in the /var/opt/swm/swm.log file: *Running "/var/adm/sw/pre_update/RNG-DKRN.100". ERROR: The /dev/random or /dev/urandom device special files may not be in use during update-ux. Use the fuser(1M) command to identify these processes, then terminate them.
Table A-1 Known Install and Update Problems (continued) Problem Description/Action Online replacement (OLR) of a LAN card in a Serviceguard cluster fails on a system running HP-UX 11i v3 because the Critical Resource Analysis (CRA) performed as part of the OLR operation returns CRA_SYS_CRITICAL. You will encounter this problem on HP-UX 11i v3 whether you use the Peripheral Device Tool (pdweb) or the HP-UX olrad command. What To Do Apply patch PHNE_35894. You can apply the patch without a reboot.
B Controlling Memory Utilization of VxFS 4.1 This appendix discusses the effect of two VxFS tunables, vx_ninode and vxfs_bc_bufhwm, on system memory consumption and provides guidelines on setting them for machines with relatively low RAM.
Introduction VxFS 4.1 caches objects in memory to improve performance. Most of the memory consumed by VxFS is used to cache inodes (in the inode cache) and metadata (in the buffer cache). The sizes of these caches and the behavior of VxFS are controlled by a set of tunables. You can tailor the performance of VxFS to meet a variety of usage scenarios while taking into account variations in machine configurations via the use of these tunables.
Controlling the inode Cache As a matter of course, VxFS file systems allocate and free up inodes as required by the load on the file system. VxFS caches these inodes for better performance (faster lookups). In general, larger inode caches help file systems perform better for file server and web server loads. The global (static) tunable vx_ninode represents the maximum possible size of the VxFS inode cache.
Conclusion VxFS uses in-memory caches for objects that result in improved file system performance. The cache sizes are controlled by tunables that are auto-tuned at boot time by the driver. For situations where the auto-tuned values are not optimal, you can set these tunables. 134 Controlling Memory Utilization of VxFS 4.
C HP-UX 11i v3 Software Bundles This appendix describes the software bundles included in the HP-UX 11i v3 media contents. HP-UX 11i v3 has a new OE structure that provides more flexibility in managing the products you wish to install and update on your system. The new OE structure makes it easier and more reliable to incrementally update your system with OE software components.
Required Software The software listed in Table C-1 is required and always installed with the HP-UX 11i v3 operating system. Table C-1 Required Software Description Bundle Name HP-UX 11i v3 operating system software. This is a core bundle.
Table C-1 Required Software (continued) Description Bundle Name Obsolescence bundle OBSOLESCENCE NOTE: The Obsolescence product is required during an OE update to remove products that are obsolete or unsupported in HP-UX 11i v3. The Obsolescence product is automatically removed from the system at the end of the OE update process. The Obsolescence product is not needed and not installed during a cold install.
Recommended Software The software bundles listed in Table C-2 are installed or updated by default. You can deselect any of these bundles before you install or update your system; however make sure that any bundle you select or deselect does not have a dependency. For example, you may deselect a software bundle that is necessary for another program to work correctly.
Table C-2 Recommended Software (continued) Description Bundle Name Contains language-specific input methods, printer and terminal HPUXExtns-Jpn support, fonts and utilities. HPUXExtns-Kor HPUXExtns-SCh HPUXExtns-TCh Base VXFS 4.
Table C-2 Recommended Software (continued) Description Bundle Name HPUX TCPWrapper daemon HPUX-TCPWRAP This is a core bundle. HP Name Server HPUX-NameServer HP-UX Secure Shell SecureShell HP-UX Gated and Mrouted Server HPUXGatedMrouted This is a core bundle.
Table C-2 Recommended Software (continued) Description Bundle Name PRM Kernel Software PRMKernelSW (Not available on the TCOE) Software Assistant SwAssistant System Management Homepage SysMgmtWeb VMGuest (HP Integrity Servers Only) VMGuestLib Veritas Volume Manager Base-VXVM HP-UX Web Server Suite HP-UX Apache-based Web Server hpuxwsApache HP-UX Tomcat-based Servlet Engine hpuxwsTomcat HP-UX Webmin-based Admin hpuxwsWebmin HP-UX XML Web Server Tools hpuxwsXml Java Bundles Runtime Environ
Table C-2 Recommended Software (continued) Description Bundle Name HP Serviceguard T1905CA HP Serviceguard NFS Toolkit B5140BA Workload Manager B8843CA Workload Manager Toolkits WLMToolkits EOE and MCOE Only GlancePlus Pak B3701AA High Availability (HA) Monitors B5736DA MirrorDisk/UX LT B2491BA OnlineJFS 4.
Optional Software The bundles listed in Table C-3 are not installed or updated by default. You must select the desired optional software bundles prior to installing or updating your system. Table C-3 Optional Software Description Bundle Name Common Desktop Environment (CDE) bundle (xxx is language variable). CDE-xxx NOTE: CDE is an optional product in HP-UX 11i v3. If you require it, you must explicitly select the CDE bundle (CDE-XXX). This applies if you need dtterm, which is located in CDE.
Table C-3 Optional Software (continued) 144 Description Bundle Name PCIMux PCIMUX-00 PCIMux TERMIO-00 HP-UX 11i v3 Software Bundles
Index Symbols /etc, 58 /etc/passwd, 86 /home, 86 /local, 86 /opt, 58, 86 /usr, 86 /usr/local/, 58 10GigEthr, 143 A actions menu, 97 adding sources, 95, 99 additional software, 42, 79 administration, 15 alternate install methods, 88 Analysis Dialog, 100 Apache-based Web Server, 14 applications, 107 configuring after update, 85, 105 automatic scrolling, 101 B backup, 58, 59, 63, 114 Base Logical Volume Manager, 136 Base VXFS 4.
error codes with update-ux, 90 errors, 117 examples update optional software, 105 update-ux, 103 updating 11i v2 OE, 104 F factory ignition, 31, 88 Fast Boot, enable, 74 feedback, 14 file partitions, 23 file sizes, 24 file system, 71, 78 firmware recommendations, applying patches, downloading updates, 28 flowchart update process, 89 FOE, 104 forums, 15 Foundation OE, 104 frecover, 86 G GigEther-00, 137 GigEther-01, 137 GlancePlus Pak, 142 global tunables VxFS, 132 Gnome GTK+, 139 golden images, 88 Graphic
ioscan, 91, 92 ioscan command, 108 Itanium-based server, 14 ITRC, 15 J Java Out-of-Box, 143 Java Out-of-box Utility, 143 JAVAOOB, 143 N Netscape Directory Server Version 7, 143 network data collection, 72 network depot, 91 network drivers, 84 new root, 86 NIS, 72 notes, 117 nPartition Provider commands, 136 nslookup, 72 O K kernel, 60 rebuilding, 60 known problems, 117 L languages, 15 legal notice, 2 localization, 15 log files cleaning, 58, 59, 60, 61 renaming, 60 logfile, 101 LVM, 71, 86 M make_net_re
Security Level 10, 143 Security Level 20, 143 Security Level 30, 143 Software Package Builder, 143 TermlO-00, 144 updating, 105 OS, 29 updating, 87 overview updating, 88 P parMgr, 15 Partition Manager, 15 Pay Per Use, 143, 144 PCI drivers, 27 PCIMux, 144 Perl, 140 planning, 25 post-installation tasks, 85 pre-defined security, 41 pre-installed, 31 problems install, 118 update, 118 process update, 88 Process Resource Manager, 142 product description button, 101 summary button, 101 protocols secured, 46 Provi
SCM, 15 SCSI, 27 scsiU320-00, 137 SD, 15 Sec00Tools, 41 Sec10Host, 41 Sec20MngDMZ, 41 Sec30DMZ, 41 secured protocols, 46 services, 46 security dependencies, 45 install-time HP-UX Bastille, 41 pre-defined, 41 settings, 46, 48 Security Level 10, 143 Security Level 20, 143 Security Level 30, 143 Selectable Software Pay Per Use, 143, 144 selectable drivers, 27 selecting additional software, 42, 79 SerialSCSI-00, 137 servers, 14 Servicecontrol Manager, 15 services secured, 46 Servlet Engine, 141 set_parms, 84 se
vs.
