Veritas 5.0.1 Installation Guide HP-UX 11i v3 (5900-2464, September 2012)

2. Create the configuration file for the HP-UX 11i v3 OE depot. If you want VxVM_5.0.1
DGV=140, which is compatible only with VxVM_5.0.1 software, either comment-out or delete
the vxvm_version=4.1 entry at the end of the OE configuration file.
3. To register the HP-UX 11i v3 OE depot, complete the following steps:
a. # cd /var/opt/ignite/data/Rel_B.11.31
b. # /opt/ignite/bin/make_config \
- s <depot_server>:<1131_OE_depot> \
-c <OE_config_filename>_cfg
c. Test the configuration file.
# /opt/ignite/bin/instl_adm –T –f <OE_config_filename>_cfg
4. Create the configuration file for the HP-UX 11i v3 Veritas VxVM/VxFS 5.0.1 depot:
a. # cd /var/opt/ignite/data/Rel_B.11.31
b. # /opt/ignite/bin/make_config \
- s <depot_server>:<1131_Vx*5.0.1_depot> \
-c <VX_config_filename>_cfg
c. Test the configuration file:
# /opt/ignite/bin/instl_adm –T –f <VX_config_filename>_cfg
5. Combine both configuration files into a single Ignite-UX INDEX configuration clause:
a. # vi /var/opt/ignite/INDEX
b. Append a new configuration clause, such as:
cfg “HP-UX B.11.31_Sept2007_OE-Vx50” {
description “B.11.31_Sept2007_OE-Vx50 – 2 depots”
“/opt/ignite/data/Rel_B.11.31/config”
“/var/opt/ignite/data/Rel_B.11.31/<0E_config_filename>_cfg"
“/var/opt/ignite/data/Rel_B.11.31/<VX_config_filename>_cfg"
“/opt/ignite/data/Rel_B.11.31/hw_patches_cfg”
“/var/opt/ignite/config.local"
}
c. Test all the configuration files in the INDEX file.
# /opt/ignite/bin/instl_adm –T
6. If you plan to LAN boot the client, add its boot entry in the appropriate file on the server. This
step is not required if you plan to initiate the cold-install from the Ignite-UX server and the client
is up.
a. For an Intel® Itanium®-based client:
1. # vi /etc/bootptab
2. Update the System-IPF entry with client_hostname and other relevant values.
b. For a PA-RISC client:
1. # vi /etc/opt/ignite/instl_boottab
2. Append an entry for the client using the following format:
<client_IP_addr>:<client_MAC_addr>::reserve # <client_hostname>
Cold-Installing the Client
To cold-install the client, complete the following steps:
1. Boot the client, whose hardware supports B.11.31. For a list of supported systems, see the
HP-UX 11i v3 Release Notes .
2. Use Ignite-UX to cold-install using the two depots referenced in the Ignite-UX server INDEX
configuration clause created above. In the Ignite-UX interface, make your selection in the Basic
tab Configurations line, such as “HP-UX B.11.31_Sept2007_OE-Vx50”.
Cold-Installing VxVM 5.0.1 and VxFS 5.0.1 with HP-UX 11i v3 31