Veritas 5.0.1 Installation Guide, HP-UX 11i v3, First Edition, November 2009

If there are multiple HP-UX 11i v3 DVDs, repeat this step for DVD.
2. Alternatively, you can copy the DVD contents in an interactive mode wherein you mount
the DVD and use the Find Local CD-ROM option in the Specify Source screen by entering
the following command:
# swcopy -i \* @ /var/depots/my_hpux_depot
3. Copy the contents of the HP-UX ServiceGuard and StorageManagement Products media
into the depot folder you created:
# swcopy -s /11iv3SG_DVD \* @ /var/depots/my_hpux_depot
For example, copy the /11iv3SG_DVD into the same HP-UX depot.
If there are multiple ServiceGuard and StorageManagement DVDs, you must repeat this
step for each DVD.
4. If you plan to use this HP-UX depot to update systems other than the system where the
depot resides, you must register the HP-UX depot. The swcopy command automatically
registers the depot when it is first created. However, HP recommends that you register the
depot again such that it is visible to other systems. Enter the following command to register
the HP-UX depot:
# swreg -l depot @ /var/depots/my_hpux_depot
5. If you are updating from the HP-UX 11i v2 operating system, you must update to the HP-UX
11i v3 Update-UX version from the HP–UX 11i v3 depot before executing the update-ux
command:
# swinstall -s/var/depots/my_hpux_depot Update-UX
6. On each system that must be updated to HP–UX 11i v3, enter the following command:
# update-ux -s depot_server_name:/var/depots/my_hpux_depot \
!Base-VxVM-50 B3929GB \
B9116DB Base-VxFS-501 Base-VxTools-501 Base-VxVM-501 VxFS-SDK-501
If the HP-UX depot resides on the system that must be updated, you need not specify the
name of the depot server using the depot_server_name option. The depot_server_name
option indicates the hostname of the system where the my_hpux_depot resides followed
by a colon (:).
This command updates the system to HP-UX 11i v3 and VxVM 5.0.1 and VxFS 5.0.1. The
!Base-VxVM-50 entries on the command line ensure that VxVM 5.0 is not installed from
the depot during the update.
When you update HP-UX 11i v2 systems that include VxVM 3.5, the following message is
displayed:
WARNING: The following was found while selecting software:
- There are new revisions of SW available in the source that would
update SW already installed on the system. The newer revisions are
not selected for installation. This will leave the incompatible old
revision of SW on the system. The affected SW is:
- VRTSfspro.FSPRO-PRG,r=4.1x replaces
VRTSfspro.FSPRO-PRG,r=3.5_2_ga08.006
- VRTSfspro,r=4.1x replaces VRTSfspro,r=3.5_2_ga08.006
- VRTSob.VEAS-FILESET,r=3.2.555.1 replaces
VRTSob.VEAS-FILESET,r=3.2.532.0.001
- VRTSob,r=3.2.555.1 replaces VRTSob,r=3.2.532.0.001
- VRTSobgui.VEA-FILESET,r=3.2.555.1 replaces
VRTSobgui.VEA-FILESET,r=3.2.532.0.001
- VRTSobgui,r=3.2.555.1 replaces VRTSobgui,r=3.2.532.0.001
- VRTSvlic.VLIC-RUN,r=3.02.23.1 replaces
VRTSvlic.VLIC-RUN,r=3.01.IA.002.010
- VRTSvlic,r=3.02.23.1 replaces VRTSvlic,r=3.01.IA.002.010
- VRTSvmdoc.VXVM-DOC,r=4.1.032 replaces
VRTSvmdoc.VXVM-DOC,r=3.5~IA.014
Updating HP-UX and Veritas Products Using the update-ux Command 37