auto_adm.1m (2012 03)

a
auto_adm(1M) auto_adm(1M)
NAME
auto_adm - manage LIF AUTO configuration files
SYNOPSIS
/opt/ignite/bin/auto_adm
[
-p platform ][-f infile][-o outfile][-O
output_format][-? ]
/opt/ignite/bin/auto_adm
[ -p platform ] -n -T timeout -M message -l label -c command
-b device -i image [ -o outfile][
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[
-p platform ] -a -l label -c command -b device -i image
[
-f infile][-o
outfile][-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[
-p platform ] -A appendfile -f infile [ -o outfile ]
[
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[
-p platform ] -L label record_modifier [ -f infile][-o
outfile]
[
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[
-p platform ] -d -L label [ -f infile][-o outfile ]
[
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[
-p platform ] -D -L label [ -f infile][-o outfile ]
[
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[ -p platform ] -T timeout [ -f infile][-o outfile ]
[
-O output_format][
-? ]
/opt/ignite/bin/auto_adm
[ -p platform ] -M message [ -f infile][-o outfile ]
[
-O output_format][
-? ]
DESCRIPTION
The
auto_adm command is used to manipulate LIF autoconfiguration files.
auto_adm manages files in two different formats, auto_conf (CONF) and Initial System Loader (
ISL)
format. See auto_adm (4) for a description of these formats.
auto_adm may read and write either
format, and convert between formats. auto_adm defaults to PA architecture unless IA is specified
with -p platform.
record_modifier consists of at least one (and optionally any combination) of
-l label,
-c command, -b
device,and/or-i image.
Options
auto_adm recognizes the following options:
-p platform
Specifies the hardware platform of either IA or PA. If the platform is
IA, no LIF volume
manipulations will apply. If omitted, platform is assumed to be
PA.
-f infile
Specifies the input file name. If file name is a LIF volume, an ISL-formatted file entitled
AUTO is read from that volume. If -f is omitted, data is read from standard input.
auto_adm uses the following rules to determine the input format:
• If file name is a LIF volume, or the file begins with the characters
hpux, the input format
is assumed to be in ISL format.
• Otherwise it is assumed to be in
CONF format.
-o outfile
Specifies the output file name. If outfile is a LIF volume, a file entitled AUTO is written to
that volume. If omitted, data is written to stdout.
-O output_format
Specifies the format of outfile, either CONF or ISL. The default is CONF. If the file specified
by -o is a LIF volume, the output format must not be CONF.
-n Create a new AUTO or auto_conf file, and initialize it with data specified by the -T, -M, -
l, -c, -b and -i options.
-T timeout
Specifies the timeout in seconds before the default action is taken. Zero (0) means wait
indefinitely.
HP-UX 11i Version 3: March 2012 − 1 − Hewlett-Packard Company 1