sasmgr.1m (2010 09)

ManualsBrandsHP ManualsSoftwareHP-UX Manpages

sasmgr(1M) sasmgr(1M)

NAME

sasmgr - utility to manage HP-UX Serial Attached SCSI (SAS) Mass Storage I/O cards / HBAs

SYNOPSIS

Path:

/opt/sas/bin

sasmgr [-h][-f] add -D

device_ﬁle -q raid -q level=raid_level

-q enc_bay=enc:bay[,enc

:bay][-q size=size][-q rebuild_rate=

rate]

sasmgr [-h][-f] add -D

device_ﬁle -q raid -q spare -q enc_bay=enc:bay

sasmgr [-h][-f] bdr -D

device_ﬁle -q lun={all | lun_dsf }

sasmgr [-h] clear_stat -D device_ﬁle

-q all

sasmgr [-h] clear_stat -D device_ﬁle

-q phy={all | phy_id }

sasmgr [-h] clear_stat -D device_ﬁle

-q phy_in_port={all | phy_id }

sasmgr [-h] clear_stat -D device_ﬁle

-q target={all | sasaddr }

sasmgr [-h][-f] delete -D

device_ﬁle -q raid -q raid_vol={rvol_id | all}

sasmgr [-h][-f] delete -D device_ﬁle -q raid -q spare

sasmgr [-h][-f] disable -D device_ﬁle

sasmgr [-h][-f] download -D device_ﬁle -q downloadfile=

ﬁlename -q enc_bay=enc:bay

sasmgr [-h][-f] download -D device_ﬁle -q downloadfile=

ﬁlename

-q ctrl=ctrl_device_ ﬁle

sasmgr [-h][-f] download -D device_ﬁle -q downloadfile=

ﬁlename

-q hba

sasmgr [-h] enable -D device_ﬁle

sasmgr [-h] get_info -D device_ﬁle

sasmgr [-h][-N] get_info -D device_ﬁle -q lun={all | lun_dsf }

sasmgr [-h][-v][-N] get_info -D device_ﬁle -q lun={

all | lun_dsf } -q lun_locate

sasmgr [-h] get_info -D device_ﬁle -q pci_id

sasmgr [-h] get_info -D device_ﬁle -q phy={all | phy_id }

sasmgr [-h] get_info -D device_ﬁle -q phy_in_port={all | phy_id }

sasmgr [-h][-N] get_info -D device_ﬁle -q raid

sasmgr [-h] get_info -D device_ﬁle -q reg={all | offset }[

-q reg_type={ pci_config |

mmio }]

sasmgr [-h] get_info -D device_ﬁle -q smp=ﬁle_name

sasmgr [-h] get_info -D device_ﬁle -q smp_addr

sasmgr [-h] get_info -D device_ﬁle -q target={all | sasaddr }

sasmgr [-h] get_info -D device_ﬁle -q vpd

sasmgr [-h] get_stat -D device_ﬁle

sasmgr [-h] get_stat -D device_ﬁle -q phy={all | phy_id }

sasmgr [-h] get_stat -D device_ﬁle -q phy_in_port={all | phy_id }

sasmgr [-h] get_stat -D device_ﬁle -q target={all | sasaddr }

sasmgr [-h][-f] replace_tgt -D device_ﬁle -q old_dev=lun_dsf

-q new_tgt_hwpath=new_hw_path

sasmgr [-h][-f] replace_tgt -D device_ﬁle -q old_dev=old_lun_dsf

-q new_dev=new_lun_dsf

sasmgr [-h][-f] replace_tgt -D device_ﬁle -q old_tgt_hwpath=old_hw_path

-q new_tgt_hwpath=new_hw_path

HP-UX 11i Version 3: September 2010 − 1 − Hewlett-Packard Company 1

Summary of content (8 pages)

PAGE 1
sasmgr(1M) sasmgr(1M) NAME sasmgr - utility to manage HP-UX Serial Attached SCSI (SAS) Mass Storage I/O cards / HBAs SYNOPSIS Path: /opt/sas/bin sasmgr [-h][-f] add -D device_file -q raid -q level=raid_level -q enc_bay=enc:bay[,enc:bay] [-q size=size] [-q rebuild_rate=rate] sasmgr [-h][-f] add -D device_file -q raid -q spare -q enc_bay=enc:bay sasmgr [-h][-f] bdr -D device_file -q lun={all | lun_dsf } sasmgr [-h] clear_stat -D device_file sasmgr [-h] clear_stat -D device_file -q all sasmgr [-h] clear_sta
PAGE 2
sasmgr(1M) sasmgr(1M) sasmgr [-h][-f] reset -D device_file sasmgr [-h] set_attr -D device_file -q lun=lun_dsf -q locate_led={on | off} sasmgr [-h][-f] set_attr -D device_file -q raid -q raid_vol=rvol_id -q state=vol_state sasmgr [-h][-f] set_attr -D device_file -q raid -q raid_vol=rvol_id -q rebuild_rate=rebuild_rate DESCRIPTION sasmgr is a common diagnostic tool used for all Serial Attached SCSI (SAS) I/O cards / Host Bus Adapters (HBAs).
PAGE 3
sasmgr(1M) sasmgr(1M) The size of the disk specified should be greater than the size of at least one of the physical disks in the volume. If the -f option is not specified, sasmgr displays a warning message before continuing the command. Otherwise, it suppresses the warning message and continues executing the command. This command requires superuser privileges. Refer to the Security Restrictions section below.
PAGE 4
sasmgr(1M) sasmgr(1M) qualifier takes the enclosure and bay of the disk for which the firmware update is to be done. If the -f option is not specified, sasmgr displays a warning message before continuing the command. Otherwise, it suppresses the warning message and continues executing the command. downloadfile ctrl Updates the firmware on the specified enclosure. The downloadfile qualifier takes the name of the file containing the new firmware.
PAGE 5
sasmgr(1M) sasmgr(1M) smp_addr Shows the SMP initiator SAS address to send SMP requests. target Shows information about a specific target or all targets. vpd Shows vital product data information for the SAS I/O card / HBA. get_stat When the get_stat command is run without qualifiers, it shows statistics about the SAS I/O card / HBA represented by device_file . The following qualifiers are specified with the get_stat command: phy Shows statistics for all PHYs or a specific PHY.
PAGE 6
sasmgr(1M) sasmgr(1M) reset Resets the SAS I/O card / HBA and performs a complete re-initialization. This is a destructive operation. Some I/Os can be aborted by this command. If the -f option is not specified with this command, sasmgr displays a warning message before continuing. Otherwise, it suppresses the warning message and executes the command.
PAGE 7
sasmgr(1M) sasmgr(1M) Delete the Core I/O card / HBA Spare on the HBA whose device file is /dev/sasd0: sasmgr delete -D /dev/sasd0 -q raid -q spare Change the state to ACTIVE for the RAID volume with volume id 3. sasmgr set_attr -D /dev/sasd0 -q raid -q raid_vol=3 -q state=ACTIVE Change the rebuild rate to 20% for the RAID volume with volume id 3. sasmgr set_attr -D /dev/sasd0 -q raid -q raid_vol=3 -q rebuild_rate=20 Update the firmware on the specified HBA.
PAGE 8
(Notes) A (Notes) sA 8 Hewlett-Packard Company −1− HP-UX 11i Version 3: September 2010