HP-UX SNAplus2 Release Notes HP-UX 11i v1 Manufacturing Part Number: J6380-90003 September 2005 U.S.A. © Copyright 2005, Hewlett-Packard Company. All rights reserved.
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.
HP-UX SNAplus2 R7.11.11.001 Release Notes Announcement 1 HP-UX SNAplus2 R7.11.11.001 Release Notes Announcement This version of SNAplus2 (R7.11.11.001) is supported on machines running HP-UX 11i v1 operating systems.
HP-UX SNAplus2 R7.11.11.001 Release Notes What’s in This Version What’s in This Version This version of SNAplus2 (R7.11.11.001), referred to in this document as SNAplus2 R7 is supported on the HP-UX 11iv1 operating system.
ASUITE is a set of APPC applications. Use ASUITE to perform functions such as file transfer and others. — Full Duplex APPC Full Duplex APPC is an addition to the existing APPC interface that allows transaction programs (TP) to send and receive data at the same time. — Session Level interface (SLI) SLI is an extension of an LUA interface, working at a higher level. SLI allows you to work at a logical message level, rather than being concerned with the details of individual request units (RU).
HP-UX SNAplus2 R7.11.11.
HP-UX SNAplus2 R7.11.11.001 Release Notes Known Problems and Workarounds Known Problems and Workarounds Following are the known problems in this release of SNAplus2: • To use SNAplus2 on HP-UX 11i to control a large number of resources (hundreds of sessions or conversations), HP recommends that you install the following O/S patch: PHKL_23445. This patch is available to download at http://www.itrc.hp.com. • SNAplus2 Release 5.x and SNAplus2 Release 7.
HP-UX SNAplus2 R7.11.11.001 Release Notes Compatibility Information and Installation Requirements Compatibility Information and Installation Requirements The following section lists the hardware and software requirements for the HP SNAplus2EE Link product. For the hardware and software requirements for SNAplus2 User Applications, refer to the HP-UX SNAplus2 Installation Guide, available at: http://www.docs.hp.com/en/netcom.
HP-UX SNAplus2 R7.11.11.001 Release Notes Compatibility Information and Installation Requirements Running HP SNAplus2EE Link in a client/server environment requires additional LAN/9000 Link software components for servers and workstations. Running HP SNAplus2EE Link using QLLC requires X.25 (J2793A) software. Running HP SNAplus2EE Link using Token Ring, 802.3/Ethernet, or FDDI requires software for each link type.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Fixes in This Version This section describes the patches, software and document fixes included in this version of SNAplus2. Software Fixes If you are upgrading from an earlier version of SNAplus2 to R7.11.11.100, here is a list of known critical and serious problems from the earlier versions that have been fixed and included in this release.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Table 1-1 Software Fixes (Continued) SR Number Problem 8606266999 TM NMVT sent prior to UNBIND in LUA. 8606267173 RUI WRITE not completing: IPR issues in SNA. 8606268352 Critical buffer congestion detected. 8606204681 C++ CPI-C application core dumps from cmallc. 8606289627 Assert in nlu.c. 8606300552 SG TOC due to hang in sna_pcisdlc_v0_get_rw_lock. 1653299685 snap2adm: modification of LS changes adj_cp_type to END_NODE.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Table 1-1 SR Number Software Fixes (Continued) Problem 1653311605 R6:RUI_TERM fails if RUI_INIT not completed. 4701424812 Viewing config with snap2adm results in config changes. 4701425355 R6: ACC system hang when using QLLC. 4701425561 R6 SNAplus2 11.00 Dynamic tp load fails after 2 hrs under load. 4701428094 R6.10.20 SNAplus2 Link - EISA PSI link fails to start without DSR. 4701429621 R6.10.20 SNAplus2 LINK -Dep.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Table 1-1 SR Number Software Fixes (Continued) Problem 8606106196 SNAplus2 R6.10.20 - Unable to add SDLC on T500 system - SAM core dumps. 8606106251 SNAplus2 R5.1 API PHNE_14874 incorrectly refs ../../o/lib/libnof.sl. 8606106291 R6.11.00.201 NIO PSI panic at sdl_reset_port+0x13c with SDLC L2 tracing. 8606106415 SNAplus2 R6.10.20 System panic when starting SDLC Link with PHNE_19407. 8606106417 R6.11.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Table 1-1 SR Number Software Fixes (Continued) Problem 8606151854 SNAplus2 R6.11.00.BB panicked in function nrm_process_cnos_reply+270. 8606158330 R6.10.20 APPC UNKNOWN VERB returned after RECEIVE_ALLOCATE_EX issued. 8606164859 Autodial not working on EISA SNAplus2 migration. 8606166322 R6.11 64-bit: LUA gets invalid data when received RU is segmented.
HP-UX SNAplus2 R7.11.11.001 Release Notes Fixes in This Version Documentation Fixes The following changes have been made to the documentation and will become effective with this release. Table 1-2 SR Number Documentation Fixes Problem 1653245936 SNAplus2 Internal Trace not clear. (Corrected in Diagnostics Guide). 1653298133 Missing parameters in the SNAplus2 Admin. Command Reference. 4701430256 Device file information is misleading in the SNAplus2 Installation Guide.
HP-UX SNAplus2 R7.11.11.001 Release Notes Software Availability in Native Languages Software Availability in Native Languages This version of SNAplus2 is available only in English.
