HP Netserver LP 1000r User Guide (1.13 and 1.26 GHz) Online Version: 2.
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1 Controls, Ports, and Indicators ...................................................................... 1 Introduction ........................................................................................................ 1 Front Panel .................................................................................................... 1 Rear View ...................................................................................................... 4 Applying Power to the HP Netserver ...........
Contents Removing DIMMs ............................................................................................ 33 5 Installing Additional Boards......................................................................... 35 Introduction ...................................................................................................... 35 Tested PCI Boards ...................................................................................... 35 Tools Required ..........................................
Contents Tools Required ............................................................................................ 73 Rack Configuration Tools ............................................................................ 73 Safety Precautions ...................................................................................... 74 Preparing the Rack .......................................................................................... 75 HP Netserver Rack Mount Parts List .............................
Contents Netserver Will Not Power On ...................................................................... 98 Problems after Netserver is Powered On.................................................... 99 Error Messages ............................................................................................. 100 POST Error Messages .............................................................................. 102 Power-On Self Test (POST) Error Codes .................................................
1 Controls, Ports, and Indicators Introduction Before operating the HP Netserver LP 1000r, familiarize yourself with the Netserver's controls, ports, and indicators, as shown in Figures 1-1 through 1-3. Front Panel The front panel of the HP Netserver provides the controls and indicators commonly used when operating the Netserver.
Chapter 1 Controls, Ports, and Indicators FDD Eject Button CD-ROM Eject Button CD-ROM CD-ROM Activity LED SCSI Disk ID 0 FDD Activity LED SCSI Disk ID 1 Flexible Disk Drive (FDD) SCSI Disk ID 2 Figure 1-2. Input and Storage Device Controls Table 1-1.
Chapter 1 Controls, Ports, and Indicators Table 1-2. Component Indicators LED ICON Temperature LED Description This Temperature LED has four distinctive states and is linked to the two processors and a sensor on the system board. • Steady Green for normal operation. • Alternating Green/Red indicates the temperature has crossed the warning threshold. If this condition continues a system crash and possible data corruption will occur. Must take action to correct problem.
Chapter 1 LED ICON Controls, Ports, and Indicators Description Disk ID 0, ID 1, and ID 2 LED These Disk LEDs have five distinctive states for the respective SCSI disk drive: • Off for SCSI drive not present • Steady Green for SCSI drive present • Steady Red for a SCSI drive failure • Alternating Green/Red at 1 Hz blink rate for a SCSI drive rebuild • Alternating Green/Red at 3 Hz blink rate for SCSI drive identification SCSI Activity This LED is the SCSI Hard Disk Drive Activity indicator and has two
Chapter 1 Controls, Ports, and Indicators • The two LAN ports (LAN A/MGMT and LAN B) are for embedded controllers based on Intel's 82559 10/100 BaseT Fast Ethernet controller. Only LAN A/MGMT is used with Alert-on-LAN 2 (AOL2) and Wake-onLAN remote management functions. Each one has a RJ-45 LAN connector and two LEDs to indicate LAN speed and valid connection. Refer to Table 13 for the LAN LED indicators and Chapter 10, "Configuring the HP Netserver.
Chapter 1 Controls, Ports, and Indicators Applying Power to the HP Netserver Powering-Up the Netserver NOTE Turn on power to the monitor connected to the HP Netserver before you power-on the Netserver. This allows proper auto-configuration of video output of the Netserver as it boots up. 1. Ensure the HP Netserver's power cord is connected to the power source. See Figure 1-3. 2. Press the Power push-button on the front control panel. See Figure 1-1.
Chapter 1 Controls, Ports, and Indicators Connecting AC Power to Multiple-Server Configurations The HP Netserver temporarily draws a large "inrush current" when first connected to an AC power source. This also occurs when the Netserver is in a standby mode (power is turned off, but the power cord is plugged into AC power). The inrush current is much greater than the Netserver's normal operating current, and generally the AC power source can handle the normal inrush current.
Chapter 1 Controls, Ports, and Indicators The Netserver supports certain types of system activity, which is used as wake-up events from these sleep states. These wake-up events can be generated from the power button, LAN activity, and scheduled events. NOTE The HP Netserver’s power management policies (transitions between various power states) and the user options are specific to the particular ACPI-compliant NOS installed on the Netserver.
2 Opening and Closing the HP Netserver Introduction This chapter describes how to the remove the top cover, front bezel, and the air duct from the HP Netserver LP 1000r. WARNING Before removing the top cover, always disconnect the power cord and unplug telephone cables. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects, such as tools or jewelry.
Chapter 2 Opening and Closing the HP Netserver 4. Pull and lift the bezel out toward you and remove it from the chassis. See Figure 2-1. Figure 2-1. Front Bezel Location NOTE The front bezel pivots on two pins at the bottom and is held in place at the top with spring latches holding onto the top pins. The middle pins limit bezel rotation to an 80° angle. Replacing the Front Bezel 1. Place the bottom edge of the front bezel into the hinge pins at the bottom front of the chassis. 2.
Chapter 2 Opening and Closing the HP Netserver Removing the Top Cover To remove the top cover, follow these steps: NOTE You do not need to remove the front bezel to remove the top cover of the Netserver. 1. If the HP Netserver is operating, log off all users and shutdown the operating system. Refer to the instructions in Chapter 1, "Controls, Ports, and Indicators." 2. Disconnect the power cord and any cables attached to the Netserver. 3.
Chapter 2 Opening and Closing the HP Netserver Figure 2-2. Removing the Top Cover Replacing the Top Cover To replace the top cover, follow these steps: 1. If the HP Netserver is already laying on a flat surface with no power applied, continue with Step 5. 2. If the HP Netserver was operating with the cover removed, power down the operating system and turn off the Netserver's power switch. 3. Disconnect the power cord and any cables attached to the Netserver. 4.
Chapter 2 Opening and Closing the HP Netserver Figure 2-3. Replacing the Top Cover 7. Install the Netserver back into the rack and secure it to the rack. Refer to the instructions in Chapters 7, 8, or 13 (depending on the rack type) to install the chassis back into the rack. NOTE Some rack options do not require removing the HP Netserver from the rack to remove or replace the top cover.
Chapter 2 Opening and Closing the HP Netserver Removing the Air Duct The air duct directs air from the fan onto the heatsinks of both processors. The air duct also restricts access to both processors and all the DIMMs, and must be removed for full access. 1. Loosen the two captive screws holding the air duct to the system board. See Figure 2-4. 2. Remove the air duct from the system board. Figure 2-4.
3 Installing Mass Storage Devices Introduction The HP Netserver LP 1000r comes standard with an IDE CD-ROM and a flexible disk drive. The Netserver will accept up to three Hot Swap SCSI hard disk drives (HDD) in special mounting tray adapters. At least one Hot Swap SCSI hard disk drive is required for booting the Netserver. An optional SCSI tape backup drive may be connected to the external SCSI connector at the rear.
Chapter 3 Installing Mass Storage Devices • IDE Devices o The embedded IDE controller is an Enhanced-IDE dual channel controller and provides two connectors (IDE-1 and IDE-2) for IDE devices. Refer to Figure A-1,"System Board Layout," in Appendix A, "Specifications." o The IDE CD-ROM has only one connector on the cable from the primary channel (IDE-1) connector. o A secondary IDE connector (IDE-2) is available, but is not used. • SCSI Device Selection o Use only HP LVD low profile (1 inch) SCSI 3.
Chapter 3 Installing Mass Storage Devices • SCSI Drive Addressing o The addresses of the SCSI drives are automatically assigned by the drive bay location in the chassis. Refer to Figure 3-1. No SCSI ID software settings or jumpers are required if using a HP NetRAID Controller board inserted into the only PCI slot. • SCSI Device Installation Order The three Hot Swap bays support various SCSI HDD configurations.
Chapter 3 Installing Mass Storage Devices Boot Priority The Netserver's boot order should be considered when selecting a boot device. This is especially important if you are installing a board that requires an early number in the boot order. The board's boot priority is set by its location in the boot order. By default the Netserver searches for boot devices in this order: 1. IDE CD-ROM drive 2. Flexible disk drive 3. Embedded SCSI A channel (Hot Swap SCSI Drives) 4.
Chapter 3 CAUTION Installing Mass Storage Devices To prevent damage to the Hot Swap SCSI hard disk drives, don't use a HVD (high voltage differential) DAC controller. If the hardware mirroring option is required (which uses the SCSI channel of the HP NetRAID Controller board), refer to " Optional SCSI Drive Controller" later in this chapter. The instructions describe how to move the SCSI cable from the system board to the SCSI connector on the HP NetRAID Controller board.
Chapter 3 Installing Mass Storage Devices Installing Hot Swap Hard Drives Use this section to install the SCSI hard drives in the Hot Swap drive bays. CAUTION Protect the drive from static electricity by leaving it in its anti-static bag until you are ready to install it. Before handling the drive, touch any unpainted metal surface to discharge static electricity. When you remove the drive from the antistatic bag, handle it only by the frame. Do not touch the electrical components.
Chapter 3 Installing Mass Storage Devices CAUTION Save the filler panel for future use. If the filler panels are left out of empty drive bays while the Netserver is operating, thermal damage and/or excessive EMI could occur. 2. Remove the SCSI drive from its protective packaging and open the ejector arms as shown in Figure 3-3. The SCSI drive should already be mounted in the Hot Swap mounting tray adapter. a. Place both thumbs in the center opening at the front of the SCSI drive. b.
Chapter 3 Installing Mass Storage Devices CAUTION To prevent snapping off the ejector arms do not apply excessive pressure. 5. Close the ejector arms by rotating each one back into place. See Figure 3-4. 6. Verify the tab on each ejector arm engages the edge of the drive bay as you close it. See Figure 3-4. Closing Ejector Arm Drive Ejector Arms Locking tab pivots when ejector arm is opened or closed. Figure 3-4. Closing Drive Ejector Arms 7.
Chapter 3 Installing Mass Storage Devices Removing Hot Swap Hard Drives CAUTION You must remove the drive slowly and then wait for the drive heads to park before completely removing the drive. Ensure you follow these instructions carefully to prevent handling damage, such as head slaps or head actuator unlocking. 1. To unlock the drive and remove it: a. Place both thumbs into the opening at the center of the drive. b. Pull out on both ejector arms with both thumbs at the same time.
Chapter 3 Installing Mass Storage Devices Figure 3-5. Removing a Hot Swap Drive CAUTION To prevent overheating or excessive electromagnetic radiation, use the filler panels to fill the unused drive bays. If the filler panels are left out of empty drive bays while the Netserver is operating, thermal damage and/or excessive EMI could occur. Optional SCSI Drive Controller Typically, this option is only used when hardware mirroring the Hot Swap SCSI drives.
Chapter 3 Installing Mass Storage Devices 3. Unfold the cable and connect it to the SCSI connector on the HP NetRAID Controller board before installing the board into the Netserver. SCSI Connector Leave SCSI cable connected here. SCSI Backplane Board Figure 3-6. SCSI Backplane Board SCSI Backplane Board Disconnect SCSI A end of Cable. Figure 3-7.
4 Installing Additional Memory Introduction The HP Netserver LP 1000r's main memory is implemented using four memory slots on the system board and it supports up to 4 GB (1 GB x 4) of memory. The Netserver uses only 3.3V, 168-pin, 133 MHz, buffered, SDRAM DIMMs and ships with at least one 256 MB DIMM. The embedded video controller is provided with 4 MB standard video memory and cannot be upgraded. NOTE Use only PC 133 (133 MHz) SDRAM DIMMs acquired from Hewlett-Packard.
Chapter 4 Installing Additional Memory Memory Installation Guidelines • The HP Netserver LP 1000r only uses 133 MHz (PC133) buffered SDRAM DIMMs, which are electrically different from the EDO and PC100 SDRAM memory modules used in other HP Netserver models. • DIMMs sizes supported are 128 MB, 256 MB, 512 MB, or 1 GB in any combination. • Supported memory capacity ranges from 128 MB to 4 GB maximum (1 GB in each of the 4 DIMM slots). The minimum capacity is 128 MB (one DIMM).
Chapter 4 Installing Additional Memory 5. Locate the DIMM slots on the system board. See Figures 4-1 and 4-2. 6. Loosen the two captive screws holding the air duct over the DIMM slots, and remove the air duct. See Figure 4-1. Figure 4-1.
Chapter 4 Installing Additional Memory 0 1 DIMM SLOTS 2 3 System Board (top view) Figure 4-2. DIMM Locations on System Board 7. Choose an empty slot on the system board to install a DIMM. DIMMs may be installed in any combination, in any slot, but HP recommends starting at slot 0 and filling the slots in order with the largest size first: DIMM slots 0, 1, 2, and 3. 8. Spread the two retaining latches on the slot outward. See Figure 4-3.
Chapter 4 CAUTION Installing Additional Memory The memory modules are sensitive to static electricity and can be easily damaged by improper handling. Do the following when handling the accessory kit: • Leave the memory module in the anti-static container until you are ready to install it. • Always use an anti-static wrist strap and a grounding mat.
Chapter 4 WARNING Installing Additional Memory Ensure you hold the DIMM tightly as you push it into the slot. It is possible to turn or bend the DIMM slightly while inserting it, which would damage or break the DIMM socket. If a DIMM socket is damaged, you must use another DIMM slot or replace the entire HP Netserver, since this Netserver is not repairable in the field. 11. Holding the DIMM at approximately 30° to the system board, press the DIMM fully into the slot until the retaining latches close.
Chapter 4 Installing Additional Memory Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a defective DIMM. 1. If the HP Netserver is already installed and working, power down the Netserver. Refer to Chapter 1, "Controls, Ports, and Indicators." 2. Disconnect the power cables and all external cables. If necessary, label each one to support re-assembly.
5 Installing Additional Boards Introduction The HP Netserver LP 1000r provides one 64-bit PCI slot connected to a riser board on the system board, which will handle a full-length 32-bit or 64-bit PCI accessory board.
Chapter 5 Installing Additional Boards Accessory Board Installation Guidelines The following sections provide the guidelines necessary to install a PCI accessory board into the HP Netserver LP 1000r. IRQ Settings The IRQ settings are automatically assigned and don't require user intervention. The HP Netserver uses the Plug-and-Play feature of the PCI board to correctly assign its resources automatically.
Chapter 5 Installing Additional Boards Remote Control Card The HP Netserver LP 1000r supports the HP Remote Control (PCI) card, which makes use of the HP TopTools remote management software. The Remote Control card requires an I2C connection to the system board, which is provided by the I2C connector on the daughter board (Integrated Remote Assistant circuitry) installed onto the system board. See Figures 5-1 and 5-2. Integrated Remote Assistant Board (daughter board) I2 C Connector 2 Figure 5-1.
Chapter 5 Installing Additional Boards Installing the Accessory Board Use this procedure to install the accessory board and observe the installation guidelines listed earlier. 1. If the Netserver is already installed and working, power down the Netserver. Refer to Chapter 1, "Controls, Ports, and Indicators." 2. Disconnect the power cable and any external cables connected to the Netserver. If necessary, label each one to expedite re-assembly.
Chapter 5 Installing Additional Boards NOTE Refer to the Readme file, Tested Products List, or Configuration Advisor on your HP Netserver Navigator CD-ROM for helpful information about a particular PCI board type. 64-Bit PCI Slot (1) Riser Board (not shown) 2 IC Connector System Board (top view) Figure 5-2. PCI Accessory Board Slot NOTE Refer to "System Board Layout" in the Appendix A, "Specifications," for connections not shown in Figure 5-2. 7.
Chapter 5 Installing Additional Boards 8. Remove the securing clamp from the chassis and set it aside for re-assembly later. Securing Clamp Riser Board Figure 5-3. Riser Board and Securing Clamp 9. Lift up the latch and move the slot cover to the left away from the tabs and out of the chassis as shown in Figure 5-4. The PCI slot cover is held in place by the latch and must be saved for use later. NOTE 40 Save the slot cover for use later if the PCI board is removed.
Chapter 5 Installing Additional Boards Latch Tab Rest Slot Cover Tabs (2) Riser Board Figure 5-4. Removing the Accessory Slot Cover 10. If necessary, remove the riser board from the PCI slot. You may leave the riser board in place with smaller PCI boards, but you will need to remove the riser board from the PCI slot for larger PCI boards. 11. Slide the accessory board into the PCI slot on the riser board as shown in Figure 5-5.
Chapter 5 Installing Additional Boards Riser Board Installed Latch PCI Slot Figure 5-5. Inserting PCI Board-Riser Board 12. Insert the PCI board and riser board into the PCI connector on the system board. See Figure 5-5. 13. Secure the PCI board into the slot opening between the two tabs and close the latch. See Figures 5-4 and 5-5. 14. If you have a longer PCI board, you must use the board clamp to install the board into the Netserver. See Figure 5-6. a.
Chapter 5 Installing Additional Boards d. Close the latch and then close the board clamp onto the edge of the PCI board. See Figure 5-6. 15. When you have completed the PCI aboard installation, close the Netserver and return it to the rack where power can be applied. 16. Once the Netserver is returned to normal operation, you may need to install software drivers.
6 Installing an Additional Processor Introduction The HP Netserver LP 1000r ships with at least one processor on the system board (primary processor socket – CPU 1) and the voltage regulator modules (VRMs) are embedded in the system board. Both processor sockets (primary and secondary) are located on the system board. Tools Required The following tools are required to access and install or remove the processors: • ¼-inch flat blade screwdriver • An anti-static service kit (3M 8501/8502/8503 or equivalent).
Chapter 6 Installing an Additional Processor • Use only processor upgrade kits with the same HP product number. • This ensures the processor type, clock speed, and cache size are the same. • Ensure a processor is installed in the primary processor (CPU 1) socket before installing a processor in the secondary socket (CPU 2). Primary Processor (CPU 1) Secondary Processor (CPU 2) System Board (top view) Figure 6-1.
Chapter 6 Installing an Additional Processor Installing a Second Processor This section provides the instructions for installing a second processor and its accompanying heatsink on the system board. CAUTION The processor is sensitive to static electricity and can be easily damaged by improper handling. Do the following when handling the accessory kit: • Leave the processor in the anti-static bag until you are ready to install it.
Chapter 6 Installing an Additional Processor Refer to Chapter 2, "Opening and Closing the HP Netserver," to gain access to the system board. NOTE It is not necessary to remove the system board from the Netserver to install the second processor (CPU 2). 6. Loosen the two captive screws holding the air duct over the DIMM slots and remove the air duct. See Figure 6-2. Figure 6-2. Removing the Air duct 7.
Chapter 6 Installing an Additional Processor NOTE If you are upgrading the second processor to a faster processor speed than the primary processor, the primary processor must also be changed. Both processors must have the same product number, which includes the same clock speed, cache size, and FSB speed. The supported processors only perform at the rated speed indicated on the processor in the HP Netserver.
Chapter 6 Installing an Additional Processor Terminator ZIF Lever Processor Socket Figure 6-3. Removing the Terminator NOTE Retain the terminator for future use. The Netserver will not operate properly if using only one processor with no terminator installed in the second processor socket. 9. Lift the terminator out of the socket and place it on anti-static surface or bag. 10. Align the second processor over the empty processor socket.
Chapter 6 Installing an Additional Processor CAUTION Ensure you align pin-1 of the processor with pin-1 of the processor socket or pin damage will occur. 11. Insert the second processor into the socket and close the ZIF lever to fully seat the processor. You should hear the ZIF lever click when it closes properly. Pin-1 Marker Figure 6-4.
Chapter 6 Installing an Additional Processor NOTE No speed switch settings are required for the supported processors (1.13 and 1.26 GHz) in the HP Netserver. These processors rely on the internal settings within the processors and do not rely on external switch settings on the system board. Installing the Heatsink Once the processor is installed, the heatsink must be installed on top of the processor.
Chapter 6 Installing an Additional Processor NOTE The heatsinks are not reusable unless the thermal patch has been replaced each time the heatsink is removed, even if the heatsink is just temporarily removed from a processor and then re-installed on the same processor. Each time the heatsink is moved (slide) on the processor, some of the thermal material is removed from the thermal patch, which could cause poor heat transfer and overheating. 3.
Chapter 6 Installing an Additional Processor Tool Latch Hook Latch (hidden) Step A Tab Tab Processor Socket Figure 6-5. Placing the Heatsink on the Processor CAUTION Ensure the left ridge on the bottom of the heatsink fits into the groove between the processor socket and processor, while both ridges should straddle the processor. If good contact is not made between the processor and the heatsink, the processor will overheat and possible damage may occur. See Figures 6-5 and 6-6. b.
Chapter 6 Installing an Additional Processor c. While holding the heatsink down with one hand, push down with your thumb to hook the tab with the thumb latch. See Figure 6-6. Hold Down Tool Latch Hook Latch Step C Step B Figure 6-6. Setting the Latches CAUTION Failure to re-install the air duct will cause the Netserver to shut down with no messages displayed and possible damage to the processor. 5. Replace the air duct on the system board and tighten the captive screws. See Figure 6-7.
Chapter 6 Installing an Additional Processor Figure 6-7. Replacing the Air Duct Firmware and Software Changes This section describes the firmware changes provided by the HP Netserver Navigator CD-ROM and the possible need to reinstall the NOS to recognize the second processor. Upgrading the Firmware If your processor included a new HP Netserver Navigator CD-ROM, insert the CD into the HP Netserver LP 1000r CD-ROM drive and power on the Netserver.
Chapter 6 Installing an Additional Processor Reinstalling the NOS You may have to reconfigure or reinstall your NOS in order to use the additional processor. If you have gone from a uni-processor to dual-processor configuration, check your NOS documentation, or the Readme file and Configuration Advisor utilities on the HP Netserver Navigator CD-ROM. Removing a Processor and Heatsink Use this procedure to remove a processor and its heatsink. The heatsink must be removed before removing the processor.
Chapter 6 Installing an Additional Processor Refer to the heatsink installation procedure earlier in this chapter. CAUTION To prevent damage to the replacement processor, remove the old patch and install a new thermal patch to the bottom of the heatsink before installing it on the new processor. The heatsinks are not reusable unless the thermal patch has been replaced each time the heatsink is removed.
7 Rack Mounting the HP Netserver (2-Post) Introduction This chapter provides the instructions for mounting the HP Netserver in a two-post (column) non-HP rack. The illustration below shows the characteristics of the 2-post (CPI – Chatsworth Products Inc.) rack. If you have one of the four-post HP racks, see Chapter 8, "Rack Mounting the HP Netserver (4-post)," or Chapter 13, "Alternative Rack Mounting (4-post)," for instructions.
Chapter 7 Rack Mounting the HP Netserver (2-Post) B Characteristics of 2-Post Rack: A A. Column is U-shaped for easy access. B. Top is secured to ceiling to hold additional weight. C. Base is bolted to floor. C Figure 7-1. Features of 2-Post Rack NOTE If you want to mount your Netserver in a third-party rack not mentioned in this guide, you may find relevant documentation on HP's web site at the following URL: http://www.hp.
Chapter 7 Rack Mounting the HP Netserver (2-Post) NOTE If the HP Netserver is completely configured by the vendor before delivery to the customer, then mounting the HP Netserver in the rack may be the final step in the installation procedure. If the vendor configures the HP Netserver at the customer's site, installation of the network operating system and other software may occur after the HP Netserver is mounted in the rack. WARNING The HP Netserver weighs 32 lbs. (14.5 kg.) fully loaded.
Chapter 7 Rack Mounting the HP Netserver (2-Post) Rack Configuration Tools HP rack configuration tools, including white papers, are available on the worldwide web. Enter the following URL in your browser: http://www.hp.com/netserver At the Web site, search for "configuration tools" and "high density rack solutions," specifically Rack Assistant, Rack Configuration, Order Assistant, and HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r).
Chapter 7 Rack Mounting the HP Netserver (2-Post) • Circuit Overloading - Ensure the total configuration of equipment in the rack does not overload the supply circuit. To this end, check the nameplate ratings on all equipment. Consider the effect of circuit overloading on overcurrent protection and supply wiring. • Reliable Earth Grounding - Maintain reliable earth grounding of rack-mounted equipment.
Chapter 7 Rack Mounting the HP Netserver (2-Post) NOTE Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver. The tools are available at: http: //www.hp.com/netserver/support 1. Use the mounting brackets to help find the Netserver location on the columns, as shown in Figure 7-2. The screw holes cover a span of only one EIA unit, which is the height requirement of the HP Netserver. 2.
Chapter 7 Rack Mounting the HP Netserver (2-Post) Preparing the HP Netserver Each HP Netserver has two inner-rails attached at the factory and shipped to customers. These two inner-rails must be removed to attach the brackets before the Netserver can be mounted in the rack. 1. Lay the HP Netserver on a flat surface. 2. Remove the front bezel on the Netserver chassis, if not already removed. See Figure 7-3. Optional (2) Figure 7-3. Removing Existing Hardware 3.
Chapter 7 Rack Mounting the HP Netserver (2-Post) b. If you are mounting the HP Netserver as a center mount, you only need the flush mount brackets to mount to the Netserver chassis. Leave the original front mounting brackets to provide a connection for the front bezel. See Figure 7-3. 6. Mount the two flush mount brackets on the Netserver chassis using the four screws provided for each one. See Figure 7-4. Figure 7-4. Mounting Flush Mount Brackets 7.
Chapter 7 Rack Mounting the HP Netserver (2-Post) Figure 7-5. Mounting Center Mount Brackets Placing the HP Netserver in the Rack Use this procedure to position the HP Netserver into the rack and secure it in place. Once the Netserver is in the rack, you can connect the front bezel to the Netserver chassis. WARNING To prevent personal injury or damage to the equipment, use two people to mount the HP Netserver into the rack. 1.
Chapter 7 Rack Mounting the HP Netserver (2-Post) Figure 7-6. Flush Mounting in the Rack 3. Position the Netserver’s two flush mount brackets over the holes (1st & 3rd) on the face of the two columns. See Figure 7-6. The masking tape or marking pen (marker) should provide the location of the holes on the two columns. See Figure 7-2. 4. Insert one screw through each bracket into the column, preferably the top or 1st hole on the column below the marker. 5.
Chapter 7 Rack Mounting the HP Netserver (2-Post) 6. If mounting the Netserver with the center mounts, follow Steps 1-5 for the center mount brackets. See Figure 7-7. Figure 7-7.
Chapter 7 Rack Mounting the HP Netserver (2-Post) Attaching the Front Bezel The front bezel attaches to the HP Netserver by pivoting on two pins at the bottom and holding onto the top pins with spring latches. The middle pins force the bezel to rotate in or out, ensuring a rotating action. 1. Position the Bezel in front of the HP Netserver LP 1000r as shown in Figure 7-8. 2. Push in on the bottom to engage the pins, allowing it to rotate up. 3. Push the bezel in at the top to engage the spring latches.
8 Rack Mounting the HP Netserver (4-Post) Introduction This chapter provides the instructions for mounting the HP Netserver in a 4-post (column) HP System/E or System/U or third-party rack. The illustration below shows the characteristics of the System/E and System/U racks. If you have the older HP Systems rack, see Chapter 13, "Alternative Rack Mounting (4-post)," for instructions.
Chapter 8 Rack Mounting the HP Netserver (4-Post) B A C Characteristics of System/E and System/U Racks: D A. 5-Cornered Columns B. Full Panel Vent C. “HP Rack System/E” or “HP Rack System/U” Name Plate D. Numbered EIA Units E. Anti-Tip Foot Extends Out Front or Back E Figure 8-1. HP System/E and System/U Rack Features NOTE If you want to put your Netserver into a third-party rack not mentioned in this guide, you may find relevant documentation on HP's web site at the following URL: http://www.hp.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Before mounting the Netserver, plan the Netserver's location in the rack relative to other rack components. Proper placement is vital for safety and operating efficiency. For more information, refer to "Rack Configuration Tools" later in this chapter. NOTE If the HP Netserver is completely configured by the vendor before delivery to the customer, then mounting the HP Netserver in the rack may be the final step in the installation procedure.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Safety Precautions Always keep the following safety and environmental issues in mind, especially if you install the HP Netserver in a non-HP rack environment: • Optimum Operating Environment - The optimum operating conditions for the HP Netserver is in an environmental controlled computer room with a temperature range of 20 to 22° C (68 to 72° F) at 40 to 60% relative humidity.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Preparing the Rack The outer-rail assemblies must be released after shipment and the columns must be marked before mounting the outer-rail assemblies. Once the outer-rails are correctly mounted, then the HP Netserver LP 1000r can be installed into the rack. A template is not provided because the Netserver is exactly one EIA unit high and can only fit into one EIA unit, but not across two EIA units. NOTE The HP Netserver weighs 32 lbs. (14.5 kg.
Chapter 8 Rack Mounting the HP Netserver (4-Post) 3/4 CCW Release Spring Assembly 1/4 CW Figure 8-2. Releasing Spring Assembly Marking the Columns Use this section to mark the front and rear columns of the HP System/E or HP System/U rack. The outer-rails mount to the face of the front columns and the inside face of the rear columns. The masking tape (or marking pen) is used to identify and mark the locations on the columns.
Chapter 8 Rack Mounting the HP Netserver (4-Post) The screw holes cover a span of only one EIA unit, which is the height requirement of the HP Netserver. NOTE The Netserver can only be mounted into both holes of one EIA Unit, but cannot be mounted across two EIA units. You cannot use a hole in one EIA unit and a hole in another EIA unit. 2. Use the masking tape (or marking pen) to mark above the 3rd hole up on both front columns, as shown in Figure 8-3.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Anti-tip Foot Extended Leveler Screws (4) Figure 8-4. Mounting Outer-Rails to Columns 4. Match the outer-rail pins to the column holes (1st & 3rd) marked on the front and rear columns. See Figure 8-3. The mounting pins of the outer-rails should go into the inside face of the rear column and the front face of the front column. 5.
Chapter 8 Rack Mounting the HP Netserver (4-Post) A tension spring allows the outer-rails to compress during installation. The outer-rails are held in place at of the front of the rack by a flat spring tab at the rear face of the front columns. See Figures 8-2 and 8-5. 6. Repeat Steps 3 through 5 for the outer-rail on the right front and rear columns. 7. If you need to release the outer-rail assembly once it is installed into the rack, do the following: a.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Placing the HP Netserver in the Rack Use this procedure to insert the HP Netserver into the outer-rail assemblies mounted in the rack. Once the Netserver is in the rack, then you can connect the cables to the rear of the Netserver. WARNING To prevent rack instability while mounting the HP Netserver, ensure the rack's anti-tip foot is pulled forward out of the bottom of the rack. Failure to do so could result in injury and equipment damage.
Chapter 8 Rack Mounting the HP Netserver (4-Post) Figure 8-6. Mounting the HP Netserver 5. Slowly move the Netserver chassis into the outer-rail assemblies until the Netserver is completely in the rack. See Figures 8-6. The securing brackets on the front of the Netserver should stop the chassis from going all the way into the rack. 6. Secure the Netserver chassis to the rack with the captive screws.
Chapter 8 Rack Mounting the HP Netserver (4-Post) 1. Position the Bezel in front of the HP Netserver LP 1000r as shown in Figure 8-7. 2. Push in on the bottom to engage the pins, allowing it to rotate up. 3. Push the bezel in at the top to engage the spring latches. The spring latches should click when engaged. Pins Spring Latches (2) Figure 8-7.
9 Connecting the Monitor, Keyboard, Mouse, and UPS Introduction Use the procedures listed here to connect the peripheral devices to the HP Netserver LP 1000r. 1. Connect the monitor, keyboard, and mouse to the HP Netserver LP 1000r using the connections provided on the rear of the chassis. See Figure 9-1. When connecting the Netserver to peripherals, use the cable ties and labels provided with the product.
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS Connecting the UPS (Uninterruptible Power Supply) 1. If you do not have an UPS (Uninterruptible Power Supply) located in the rack, install it before attempting to connect it to the Netserver. 2. Connect the serial cable provided between the UPS and the HP Netserver. Refer to the user guide included with the UPS for additional information and ensure you configure the Netserver's serial/management port correctly in Setup (BIOS) Utility.
10 Configuring the HP Netserver Introduction This chapter describes how to configure the HP Netserver with the help of the HP Netserver Navigator CD-ROM, which is shipped with your Netserver. This CD-ROM also provides the latest information concerning your Netserver. As you configure the Netserver, it's important to have the very latest configuration information. The CD-ROM will inform you of any applicable compatibility issues, and provide you with a current list of HP-tested peripherals and accessories.
Chapter 10 Configuring the HP Netserver Contents of the HP Netserver Navigator CD-ROM The Main Menu of the Navigator CD directs you to modules where you can perform the required configuration tasks, or access the utilities used in the configuration process.
Chapter 10 Configuring the HP Netserver Status Report Identification You must compare the Document Number on your HP Netserver Navigator CD-ROM with the most current Status Report's Document Number for your HP Netserver model. • Each version of the HP Netserver Navigator CD-ROM has a four-digit Document Number, such as 77xx, corresponding to a Status Report, printed on the disk. • Each Status Report has a different Document Number.
Chapter 10 Configuring the HP Netserver • HP TopTools Software – This is the HP browser-based management software that provides remote administration and monitoring of critical Netserver components. • HP TopTools Remote Control Card – This is an accessory PCI board that provides a connection for remote LAN or modem-based server management software (HP TopTools) when installed into the Netserver.
Chapter 10 Configuring the HP Netserver Setup (BIOS) Utility The HP Netserver (BIOS) Setup Utility is used to configure the following Netserver options: • User Preferences • Security • Configuration • Exit Accessing the Setup Utility The (BIOS) Setup Utility menu offers the choices listed above, and the corresponding items are described in the topics below. 1. Turn on the monitor and the HP Netserver. 2.
Chapter 10 Configuring the HP Netserver o Integrated I/O Port - Configure ports for serial and parallel, assign base addresses and interrupts, pointing devices (mouse), and console redirection for remote control. o Flexible Disk Drive - Enable or disable the flexible disk drive controller. o CPU and Memory - Enable or disable memory cache, memory hole, and processor serial number.
Chapter 10 Configuring the HP Netserver previous screen appears. When you are making selections from a pop-up menu, use the Esc key to close the pop-up without making a selection. Changing the System Date and Time Use this topic to change the HP Netserver's date and time and refer to the following procedure. 1. To reach the Setup Utility, boot or reboot the system and press F2 when prompted. 2. If necessary, use the left-arrow key to select User Preferences from the menu bar at the top of the screen.
Chapter 10 Configuring the HP Netserver 12. Choose Exit Saving Changes from the list of exit options, then press Enter. A dialog appears and asks you to confirm your decision. 13. Choose Yes and then press Enter. Then the HP Netserver reboots. Setting the HP Netserver's Boot Passwords Use this topic to set a password to boot the HP Netserver. To configure the HP Netserver for a password, which will require a password on boot-up, refer to the following procedure. 1.
Chapter 10 Configuring the HP Netserver 4. Press the Enter key to enter a new password or change the old one. A pop-up menu appears titled, "Set Power-On Password". If no password has been entered, the field "Enter new password: [ ]" is highlighted. If a previous password has been entered, the field "Enter old password: [ ]" is highlighted. NOTE To leave the pop-up menu without entering a password, press the Esc key at any time. 5.
Chapter 10 NOTE Configuring the HP Netserver You typically would not need to use this utility unless you are an experienced administrator or requested to do so by a support provider. During the boot process the message "SCSI BIOS successfully loaded" will appear if there are devices connected to the SCSI controller. The SCSI controller can provide the bus, device, and channel configurations when active on screen. To access the Symbios SCSI Configuration Utility, refer to the following instructions. 1.
11 HP Netserver Online Documentation CD-ROM Overview The HP Netserver Online Documentation CD-ROM contains the entire set of documentation for your HP Netserver LP 1000r. The Online Documentation CD provides a web-based interface that allows you to quickly and efficiently locate necessary information including.
12 Troubleshooting Introduction If you are having problems installing your HP Netserver, there are a number of different tools available for troubleshooting, including the information provided in this chapter. • HP Netserver Online Documentation CD-ROM contains the following information in the HP Netserver LP 1000r Service Manual.
Chapter 12 Troubleshooting you need to get assistance from Hewlett-Packard, refer to the HP Netserver Warranty and Service/Support booklet provided with the Netserver. WARNING Before removing the cover, always disconnect the power cord and unplug telephone cables. Disconnect telephone cables to avoid exposure to shock hazard from telephone ringing voltages.
Chapter 12 Troubleshooting 1. Remove the AC power cord, wait 15 seconds, reconnect the power cord, and try again. 2. Ensure all cables and the power cord are firmly plugged into the proper receptacles. 3. If the Netserver is plugged into a switched multiple-outlet box, ensure the switch on the outlet box is turned on. 4. Plug a different electrical device (such as a printer) into the power outlet, and turn it on to verify if the fault is with the power supply. 5.
Chapter 12 Troubleshooting d. Clear the CMOS memory and reboot. Refer to "Clearing the CMOS Configuration" later in this chapter. 6. If you have completed a boot of the Netserver successfully, reinstall the thirdparty options one at a time, checking the Netserver after installing each option. Error Messages There are three kinds of error messages. Two message types appear on screen during the POST process and include text messages or alpha-numeric code.
Chapter 12 Troubleshooting 3. Verify the power outlet is working. 4. Verify the Netserver and monitor are turned on. The power-on indicator should be illuminated. 5. Verify the display's contrast and brightness settings are correct. 6. Verify all internal cables are properly connected and all boards firmly seated. 7. Verify the processor and its heatsink are fully seated in its socket on the system board. 8. Verify the DIMMs are installed correctly and fully seated. 9.
Chapter 12 Troubleshooting e. If the Netserver now works, replace the boards and accessories one at a time to determine which one is causing the problem. 8. If the Netserver still does not work contact your service representative to replace the Netserver. POST Error Messages If you get a POST text error message in reverse video, press the [Enter] key (View System Error) to get a more detailed explanation and a possible solution.
Chapter 12 Troubleshooting • Verify the mouse is connected to the correct connector (not the keyboard connector) at the rear of the Netserver. • Verify the connector is pushed completely. Mouse error (The LP 1000r will complete the boot process without a mouse connected.) If no message appears (screen is blank) If the problem persists, replace the mouse or contact your HP support organization. • If no text or messages appear listen for the beep codes.
Chapter 12 Troubleshooting Clearing the CMOS Configuration You may need to clear the CMOS configuration if the configuration has been corrupted, or if incorrect settings made in the Setup Utility have caused error messages to be unreadable. To clear the configuration: 1. Turn off power to the Netserver and remove the cover. 2. Move switch 4 in the configuration switch on the system board (labeled "Clear CMOS") to the ON position. See Figures 12-1 and 12-2. 3. Turn on power to the Netserver.
Chapter 12 Troubleshooting Not Used (Default =Off) BIOS Recovery Clear Password Clear CMOS Not Used (Default = Off) Not Used (Default = Off) Shaded rectangle represents the position of switch Not Used (Default = Off) Not Used (Default = Off) Figure 12-2. Configuration Switch Positions Resetting a Lost Password If you have forgotten the Power-on password, you can reset it using the configuration switch on the system board.
Chapter 12 Troubleshooting Hardware Problems This section describes what to do if you have problems with your monitor, mass storage devices, printer, accessory boards, keyboard, or mouse. Monitor Does Not Work NOTE If the Netserver has a large amount of memory installed, it may take 30 seconds for the first screen to display. 1. If nothing is displayed on the screen, but the Netserver starts and you have verified the keyboard, disk drives, and other peripheral devices are functioning properly: a.
Chapter 12 Troubleshooting Keyboard or Mouse Does Not Work 1. Verify the keyboard and mouse are connected to the correct connectors. Refer to the I/O panel label on the rear panel of the Netserver. 2. Verify the mouse is correctly defined in the control options of your NOS. 3. Clean the mouse ball and rollers using a lint-free cloth. CD-ROM Drive Does Not Work 1. Verify a CD is inserted in the drive. 2. Verify the power and data cables are correctly connected to the device. 3.
Chapter 12 Troubleshooting WARNING There is a danger of explosion if the battery is incorrectly installed. For your safety, never attempt to recharge, disassemble, or burn the old battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 1. Power down the HP Netserver and unplug power cord. 2.
Chapter 12 Troubleshooting View Rotated 90 Degrees CCW Figure 12-3. Battery on System Board 7. Insert the new battery with the positive sign (+) facing up in the socket. 8. Press down on the center of the battery with your thumb, pushing the battery down into the socket. The battery should snap into place. 9. Ensure the spring latch holds the battery firmly. 10. If necessary, replace the PCI board and replace the top cover. 11. Re-install the Netserver into the rack. 12.
13 Alternative Rack Mounting (4-Post) Introduction This chapter provides the instructions for mounting the HP Netserver in a four-post (column) HP Systems rack. Figure 13-1 shows the Systems rack. If you have the newer 4-post HP System/E or System/U racks, go to Chapter 8. If you are mounting the Netserver in a 2-post non-HP rack, refer to Chapter 7, or see the documentation in the appropriate rack accessory kit.
Chapter 13 Alternative Rack Mounting (4–Post) Figure 13-1.
Chapter 13 Alternative Rack Mounting (4–Post) Before mounting the Netserver, determine the Netserver's location in the rack relative to other rack components. Proper placement is vital both for safety and operating efficiency. For more information, refer to "Rack Configuration Tools" later in this chapter. NOTE If the HP Netserver is completely configured by the vendor before delivery to the customer, then mounting the HP Netserver in the rack may be the final step in the installation procedure.
Chapter 13 Alternative Rack Mounting (4–Post) Safety Precautions Always keep the following safety and environmental issues in mind, especially if you install the HP Netserver in a non-HP rack environment: • Optimum Operating Environment – The optimum operating conditions for the HP Netserver is in an environmental controlled computer room with a temperature range of 20 to 22° C (68 to 72° F) at 40 to 60% relative humidity.
Chapter 13 Alternative Rack Mounting (4–Post) Preparing the Rack The outer-rail assemblies must be released after shipment and the columns must be marked before mounting the outer-rail assemblies. Once the outer-rails are correctly mounted, then the HP Netserver LP 1000r can be installed into the rack. A template is not provided because the Netserver is exactly one EIA unit high and can only fit into one EIA unit, but not across two EIA units. NOTE The HP Netserver weighs 32 lbs. (14.5 kg.) fully loaded.
Chapter 13 Alternative Rack Mounting (4–Post) Figure 13-2. Releasing Spring Assembly Marking the Columns Use this section to mark the front and rear columns of the HP Systems rack. The outer-rails mount to the face of the front columns and the inside face of the rear columns. The masking tape (or marking pen) is used to identify and mark the locations on the columns.
Chapter 13 Alternative Rack Mounting (4–Post) 1. Find the EIA unit markings on the rack and the location for the Netserver. The screw holes cover a span of only one EIA unit, which is the height requirement of the HP Netserver. NOTE The Netserver can only be mounted into both holes of one EIA Unit, but cannot be mounted across two EIA units. You cannot use a hole in one EIA unit and a hole in another EIA unit. 2.
Chapter 13 Alternative Rack Mounting (4–Post) 4. Match the outer-rail pins to the column holes (1st & 3rd) marked on the front and rear columns. See Figure 13-3. The mounting pins of the outer-rails should go into the inside face of the rear column and front face of the front column. Anti-tip Foot Extended Leveler Screws (4) Figure 13-4. Mounting Outer-Rails to Columns 5. With the outer-rails held in position at the rear, push in on the front outer-rail mount.
Chapter 13 Alternative Rack Mounting (4–Post) A tension spring allows the outer-rails to compress during installation. The outer-rails are held in place at of the front of the rack by a flat spring tab at the rear face of the front columns. See Figures 13-2 and 13-5. 6. Repeat Steps 3 through 5 for the outer-rail assembly on the right front and rear columns. 7. If you need to release the outer-rail assembly once installed into the rack, do the following: a.
Chapter 13 Alternative Rack Mounting (4–Post) Placing the HP Netserver in the Rack Use this topic to insert the HP Netserver into the outer-rail assembly mounted in the rack. Once the Netserver is in the rack, you can connect the cables to the rear of the Netserver. WARNING To prevent rack instability while mounting the HP Netserver, ensure the rack's anti-tip foot is pulled forward out of the bottom of the rack. Failure to do so could result in injury and equipment damage.
Chapter 13 Alternative Rack Mounting (4–Post) Figure 13-6. Mounting the HP Netserver 5. Slowly move the Netserver chassis into the outer-rail assemblies until the Netserver is completely in the rack. See Figure 13-6. The securing brackets on the front of the Netserver should stop the chassis from going all the way into the rack. 6. Secure the Netserver chassis to the rack with captive screws.
Chapter 13 Alternative Rack Mounting (4–Post) 2. Push in on the bottom to engage the pins, allowing it to rotate up. 3. Push the bezel in at the top to engage the spring latches. The spring latches should click when engaged. Pins Spring Latches (2) Figure 13-7.
A Specifications Introduction This appendix provides the power requirements, operating conditions (environmental requirements), physical requirements, hardware specifications, and video resolutions of the HP Netserver LP 1000r. The system board layout and the unused connectors are also provided. See Figures A-1 and A-2. Requirements The following tables provide the specifications required for normal operation of the HP Netserver LP 1000r. Table A-1.
Appendix A Specifications Table A-2.
Appendix A Specifications Table A-4. HP Netserver Hardware Specifications Processors Intel Pentium III (up to 2 processors) processors, at supported speeds of 1.13 and 1.26 GHz, with 512 KB level 2 cache on processor Chipset RCC LE chip set with 133 MHz bus speed support Memory Supports up to four SDRAM DIMMS for a maximum of 4 GB. Supported DIMM types: 128 MB, 256 MB, 512 MB and 1 GB unbuffered (registered), 72 bits wide, ECC single-bit correcting, multi-bit detecting.
Appendix A Specifications System Board Layout Battery LAN B LAN A/ MGMT Video (B) Parallel (T) UBS (2) Keyboard (B) Mouse (T) PCI Slot Processor 1 Config Switch IDE-2 Processor 2 Integrated Remote Assistant Board (Daughter Board) Power Connector 0 1 DIMM Slots 2 3 FDD SCSI B SCSI A IDE-1 (B) = Bottom, (T) = Top Figure A-1.
Appendix A Specifications Not Used Wake-onLAN (WOL) Not Used PCI Board Fan Wake-onRing (WOR) Not Used Not Used Power Supply Speed Monitor Integrated RA Board Connectors (2) (Daughter Board) Not Used Memory Fan Processor (CPU) Fan Power, Reset Buttons, Power LED Management Function Not Used See Default Settings Figure A-2. System Board Connectors (Used/Unused) NOTE If the switch is loaded, refer to the following table (Table A-6, "Default Settings") for switch default settings. Table A-6.
Index A ACPI Advanced Configuration and Power Management Interface, 2, 7 Advanced Configuration and Power Management Interface ACPI, 7 air duct remove for processors, 48 air duct, 29 Air Duct removing, 14 Alert-On-LAN 2 Magic Packet, 88 Setup Utility, 88 Alert-on-LAN 2 (AOL 2) LAN A only, 90 anti-tip foot rack installation, 77, 117 B boot device order Setup Utility, 90 boot device priority boot order, 18 changing boot order, 93 boot order boot device priority, 18 CD-ROM, 18 CD-ROM, 36 default, 18 flexible d
Index DIMM sizes 1 GB, 28 128 MB, 28 256 MB, 28 512 MB, 28 DIMMs air duct removal, 29 installation, 27 installation guidelines, 28 non-compatible, 27 open slot configuration, 28 removing, 33 retaining latches, 33 slots 0 through 3, 28 supported memory capacity, 28 Disk Array Controller board HP NetRAID 1M, 36 HP NetRAID 1Si, 36 HP NetRAID 2M, 36 recommendation, 36 Diskette Library, 97 display modes, 125 Drive Array Controller (DAC), 18 drive types supported flexible disk drive, 15 IDE CD-ROM, 16 low-voltag
Index no jumper settings, 17 Hot Swap SCSI ID assigned by location, 17 no controller board jumper settings, 17 HP DiagTools Utility, 97 HP Management Solutions, 87 HP NetRAID 1M, 19 HP NetRAID 1Si, 19 HP NetRAID 2M, 19 HP Netserver rack installation, 113 tool-less rack installation, 113 HP Netserver controls, 1 front panel, 1 indicators, 1 inrush current, 7 ports, rear panel, 4 powering down, 6 powering up, 6 rack installation, 59, 71 rack mount kit, 63, 75, 115 required tools (rack installation), 61 SCSI
Index troubleshooting, 106 video connection, 83 mouse, 83 mouse troubleshooting, 107 O Order Assistant, 27 outer-rail release compression spring, 75, 115 spring tab, 79, 119 P password resetting, 105 password problems, 105 PCI board PCI-to-PCI bridge, 38 PCI boards software drivers, 43 PCI slot riser board, 38 PCI slot devices, 90 PCI slots one 64-bit slot, 35 riser board, 35 ports Alert-on-LAN 2 (AOL2), 5 keyboard, 4 LAN, 5 mouse, 4 serial, 4 Wake-on-LAN, 5 ports external, 83 external SCSI, 5 keyboard, 83
Index rack mount kit parts list, 63, 75, 115 rear panel ports, 83 Remote Control card I2C connector, 37 Remote Control card RMC, 37 removing front bezel, 9 removing top cover, 11 replacing top cover, 12 retaining latches DIMMs, 31 S SCSI channels changing boot order, 93 SCSI configuration utility Symbios SCSI Configuration Utility, 93 SCSI configuration utility, 93 SCSI Configuration Utility change boot order, 36 SCSI controller ID, 18 SCSI device troubleshooting, 107 security hardware, 89 Setup Utility, 8
Index connection, 83 keyboard, 83 monitor, 83 mouse, 83 switch settings processor speed, 52 system board removing DIMMs, 33 system date changing, 91 T tape backup device troubleshooting, 107 tape backup drive, 16 terminator, 50 empty socket, 57 time changing, 91 top cover Closed knob position, 12 Open knob position, 11 TopTools Remote Control card supported, 37 troubleshooting battery problems, 107 CD-ROM drive, 107 heatsink problems, 98 keyboard, 107 mouse, 107 process steps, 98 troubleshooting basics, 98
