HP Netserver LP 2000r User Guide (1.13 and 1.26 GHz) Online Version: 2.
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1 Controls, Ports, and Indicators ...................................................................... 1 Introduction ........................................................................................................ 1 Front Panel ........................................................................................................ 1 Rear Panel......................................................................................................... 4 Applying Power to the HP Netserver ....
Contents Memory Installation Guidelines ................................................................... 32 Installing Additional DIMMs ............................................................................. 32 Removing DIMMs ............................................................................................ 36 5 Installing Additional Boards......................................................................... 39 Introduction ............................................................
Contents Attaching the Cable Management Arm ........................................................... 72 8 Rack Mounting the HP Netserver (2-Post) .................................................. 75 Introduction ...................................................................................................... 75 Tools Required ............................................................................................ 77 HP Netserver Rack Mount Parts List ...........................................
Contents Introduction .................................................................................................... 105 Tools Required .............................................................................................. 105 Common Installation Problems...................................................................... 106 Troubleshooting Sequence ....................................................................... 106 Netserver Will Not Power On ......................................
1 Controls, Ports, and Indicators Introduction Before operating the HP Netserver LP 2000r, familiarize yourself with the Netserver's controls, ports, and indicators, as shown in Figures 1-1 through 1-3. Front Panel The front panel of the HP Netserver provides the controls and indicators commonly used when operating the Netserver. Figure 1-1.
Chapter 1 Controls, Ports and Indicators FDD Eject Button CD-ROM Eject Button CD-ROM CD-ROM Activity LED SCSI Disk ID 0 FDD Activity LED SCSI Disk ID 1 Flexible Disk Drive (FDD) SCSI Disk ID 2 Figure 1-2. Control Panel Indicators Table 1-1. Control Panel Switches and Indicators Control/Indicator Power On/Off/Sleep Switch & LED Power Power Switch LED Description The power switch turns the Netserver power On or Off.
Chapter 1 Controls, Ports and Indicators Table 1-2. Component Indicators LED ICON Description Temperature/Fan LED This LED indicates the system temperature and fan speed status: • Steady Green indicates normal temperature and fan speed. • Alternating Red/Green indicates temperature has exceeded the warning threshold or the fan speed has fallen below the warning threshold. • Steady Red indicates temperature has exceeded the critical threshold or the fan speed has fallen below the critical threshold.
Chapter 1 Controls, Ports and Indicators Rear Panel The ports and connectors at the rear are listed below and shown in Figure 1-3. • The power connector accepts a standard power cable to connect the HP Netserver LP 2000r with a UPS or the site power source. A second power supply for redundancy is optional. Each power supply has its own power cord connection. • The mouse port accepts a standard mouse with a PS/2 connector. • The keyboard port accepts a standard keyboard with a PS/2 connector.
Chapter 1 Power Controls, Ports and Indicators Mouse Parallel Keyboard LAN A/MGMT Serial A/MGMT PCI Slot (1) LAN B Video External SCSI Connector Figure 1-3. Rear Panel and Ports Table 1-3. Rear Panel LED Indicators Indicator Definition Power Supply LED Each power supply module has a status LED: • Steady Green indicates the power supply module is powered up and operating normally.
Chapter 1 Controls, Ports and Indicators Applying Power to the HP Netserver Powering-Up the HP Netserver 1. Turn on power to the monitor connected to the HP Netserver. Turning on the monitor first ensures that video output auto-configures properly as the Netserver boots up. 2. Press the Power push-button on the front control panel. See Figure 1-1. When you press the power button, the Netserver powers up and loads the operating system.
Chapter 1 Controls, Ports and Indicators Connecting AC Power to Multiple-Server Configurations The HP Netserver temporarily draws a large "inrush current," when first connected to an AC power source. The inrush current is much greater than the Netserver's normal operating current and generally, the AC power source can handle the normal inrush current. However, if you install several HP Netservers on one circuit, precautions are necessary.
Chapter 1 Controls, Ports and Indicators The Netserver supports certain types of system activity, which is used as wake-up events from these sleep states. These wake-up events can be generated from the power button, LAN activity, and scheduled events. NOTE The HP Netserver’s power management policies (transitions between various power states) and the user options are specific to the particular ACPI-compliant NOS installed on the Netserver.
2 Opening and Closing the HP Netserver Introduction This chapter describes how to the remove the front bezel, top cover, and air flow guide from the HP Netserver LP 2000r. WARNING Before removing the cover, always disconnect the power cord and unplug cables. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry. Disconnect cables to avoid exposure to shock hazard.
Chapter 2 Opening and Closing the HP Netserver Figure 2-1. Removing the Front Bezel Replacing the Front Bezel 1. Hook the bottom edge of the bezel onto the pins at the front of the chassis. See Figure 2-1. 2. Close the bezel and press the top corners to snap it into place. Removing the Top Cover You do not need to remove the front bezel to remove the top cover of the Netserver. 1. If the HP Netserver is operating, log off all users and shut down the operating system. 2.
Chapter 2 Opening and Closing the HP Netserver 4. Release the top cover by turning the knob at the front of the chassis in a clockwise direction. See Figure 2-2. 5. Slide the top cover about ½ inch (13mm) toward the front of the Netserver and then lift it off the chassis. Figure 2-2. Removing the Top Cover Replacing the Top Cover To replace the cover, follow these steps. 1. Ensure the knob on the cover is turned to the Open position (clockwise). See Figure 2-3. 2.
Chapter 2 Opening and Closing the HP Netserver B A Figure 2-3. Replacing the Cover 3. Turn the knob to the Closed position (counter-clockwise). See Figure 2-3. 4. Slide the Netserver back into the rack.
Chapter 2 Opening and Closing the HP Netserver Removing the Rear Chassis Blower/Bracket and Air Flow Guide The blower generates the air that cools the processor heatsinks. The air flow guide directs air onto the processor heatsinks. The air flow guide sits directly over the DIMMs and must be removed to install or remove DIMMS. 1. To remove the rear chassis blower/bracket assembly, tilt up the inside edge of the rear chassis blower/bracket assembly. 2.
Chapter 2 Opening and Closing the HP Netserver Replacing the Rear Chassis Blower/Bracket and Air Flow Guide To replace the rear chassis blower/bracket and air flow guide, simply reverse the steps described in the preceding procedure. Removing the PCI Card Cage The PCI card cage contains the 3 PCI card slots on a riser board, and must be removed in order to access PCI cards. Remove the air flow guide before removing the PCI card cage (see “Removing the Air Flow Guide” earlier in this chapter). 1.
Chapter 2 Opening and Closing the HP Netserver Replacing the PCI Card Cage Follow these steps to replace the PCI card cage and reconnect the card cage fan to the system board. 1. Align the PCI card cage with the guides on the and left side of the chassis. Lower the PCI card cage and plug the fan into the connector on the system board. See Figure 2-6. 2. Press down on the top of the card cage to plug the riser card into the motherboard. 3.
3 Installing Mass Storage Devices Introduction The HP Netserver LP 2000r comes standard with an IDE CD-ROM and a slim-line flexible disk drive, and can accommodate up to six Hot Swap SCSI hard drives. A SCSI tape backup drive may be connected as an option to the external SCSI connector at the rear. Tools Required No tools are required to install a SCSI drive in the Netserver.
Chapter 3 Installing Mass Storage Devices • SCSI Device Selection o Use only HP LVD low-profile (1 inch) SCSI 3.5-inch hard disk drives in the Hot Swap drive slots. o Ensure the SCSI devices you install in Hot Swap slots do not have terminations installed. The Hot Swap backplane provides automatic termination for any unused slots. The HP Hot Swap SCSI drives come set without device ID or termination. Do not change these settings.
Chapter 3 Installing Mass Storage Devices CAUTION Thermal damage or excessive electromagnetic radiation may result if you operate the HP Netserver without filler panels inserted in empty SCSI HDD slots. Figure 3-1. HP Netserver Mass Storage Drives Boot Priority The Netserver's boot order should be considered when selecting a boot device. This is especially important if you are installing a board that requires a high priority in the boot order.
Chapter 3 NOTE Installing Mass Storage Devices The boot order can be changed using the Netserver's (BIOS) Setup Utility and the SCSI Select Utility. Refer to Chapter 10, "Configuring the HP Netserver," for more information. Installed Mass Storage Devices Table 3-1 lists the number and types of mass storage devices that may be installed in the HP Netserver LP 2000r. Table 3-1.
Chapter 3 Installing Mass Storage Devices CAUTION To prevent damage to the Hot Swap SCSI hard disk drives, do not use a HVD (high voltage differential) DAC controller. If you are mirroring hard drives using the HP NetRAID Controller board, refer to "Duplexing SCSI Hard Disk Drives" later in this chapter for instructions on how to install the SCSI cable to the SCSI backplane connector. Refer to the documentation provided by the HP NetRAID PCI Controller board for external cabling requirements.
Chapter 3 Installing Mass Storage Devices Tab Tab Figure 3-2. Removing a Filler Panel 2. Remove the SCSI drive from its protective packaging and open the ejector arms, as shown in Figure 3-3. 3. Slide the SCSI drive into the slot until you feel resistance. Then press in firmly until the drive is fully seated into the connector on the SCSI back plane. See Figure 3-3.
Chapter 3 Installing Mass Storage Devices Figure 3-3. Inserting a SCSI Drive 4. Make sure the drive is pushed in completely. Close the ejector arms and press them in until the latch clicks into place. See Figure 3-4.
Chapter 3 Installing Mass Storage Devices Figure 3-4. Closing Drive Ejector Arms 5. Verify that the drive is flush with the other drives. If the drive is not flush, it is not seated properly in the drive slot. Open the ejector arms and repeat Step 3 and 4. Make sure that you open the ejector arms wide before inserting the drive in the slot. Push the drive in completely before attempting to close the ejector arms. Removing Hot Swap Hard Drives CAUTION Remove the drive slowly.
Chapter 3 Installing Mass Storage Devices Figure 3-5. Opening Drive Ejector Arms 2. Remove the drive: a. Using both hands, grasp the ejector arms and firmly pull the drive out about an inch to disengage the connection on the backplane. See Figure 3-6. b. Wait about 30 seconds for the drive to stop spinning and for the drive heads to park. c. Use your hand to support the bottom of the drive, while you slowly pull the drive straight out. Do not allow the drive to fall. 3.
Chapter 3 Installing Mass Storage Devices Figure 3-6. Removing a SCSI Drive Duplexing SCSI Hard Disk Drives This section provides instructions for duplexing SCSI hard drives by using internal SCSI channels (see Figure 3-8) or a SCSI host bus adapter card, such as the HP NetRAID Controller board (see Figure 3-9). If you are duplexing using a SCSI host bus adapter card, you will need to install the optional SCSI accessory cable. Figure 3-7 shows the default SCSI cable configuration.
Chapter 3 Installing Mass Storage Devices Rear Front Top Connector Cable C BACKPLANE B Cable B SCSI Channel A Bottom Connector SCSI 3 SCSI 4 SCSI 5 SCSI Terminator SCSI 0 External SCSI Cable A SCSI Channel B Top Connector BACKPLANE A SCSI 1 Bottom Connector SCSI 2 Cable A = External SCSI Cable Cable B = Short Internal SCSI Cable Cable C = Long Internal SCSI Cable Figure 3-7.
Chapter 3 Installing Mass Storage Devices Front Rear Top Connector Cable C BACKPLANE B SCSI Channel A Cable B Bottom Connector SCSI Channel B (Cable A Removed) SCSI 4 SCSI 5 SCSI Terminator Top Connector External SCSI SCSI 3 BACKPLANE A Bottom Connector SCSI 0 SCSI 1 SCSI 2 Cable A = External SCSI Cable Cable B = Short Internal SCSI Cable Cable C = Long Internal SCSI Cable Figure 3-8.
Chapter 3 Installing Mass Storage Devices 4. Fold the cables in the PCI card cage as shown in Figure 3-11. NOTE Ensure the cables do not impede airflow or obstruct the PCI card cage fan.
Chapter 3 Installing Mass Storage Devices Figure 3-10. Channel 0 and Channel 1 Connectors Figure 3-11.
4 Installing Additional Memory Introduction The HP Netserver LP 2000r's main memory is implemented using four memory slots on the system board which support up to 4 GB (1 GB x 4) of memory. The Netserver uses only 3.3V, 168-pin, 133 MHz SDRAM DIMMs and ships with at least one 256 MB DIMM. The embedded video controller is provided with 4 MB standard video memory and cannot be upgraded. NOTE Use only PC 133 (133 MHz) SDRAM DIMMs acquired from Hewlett-Packard.
Chapter 4 Installing Additional Memory Memory Installation Guidelines • The HP Netserver LP 2000r only uses PC 133 (133 MHz) SDRAM DIMMs, which are electrically different from the EDO and PC100 SDRAM memory modules used in previous HP Netserver models. • DIMMs sizes supported are 128 MB, 256 MB, 512 MB, or 1 GB in any combination. • Supported memory capacity ranges from 128 MB to 4 GB maximum (1 GB DIMM in each of the 4 DIMM slots).
Chapter 4 Installing Additional Memory Figure 4-1. Removing the Air Flow Guide 6. Locate the DIMM slots on the system board, and choose an empty slot to install a DIMM. See Figure 4-2. DIMMs may be installed in any combination, in any slot, but HP recommends starting at slot 0 and filling the slots in order, with the largest size first. CAUTION Use only HP PC133 (133 MHz) SDRAM DIMMs.
Chapter 4 Installing Additional Memory 0 1 DIMM Slots 2 3 System Board (top view) Figure 4-2. DIMM Locations on System Board 7. Spread the two retaining latches on the slot outward. See Figure 4-3. 8. Remove a DIMM from its container, handling the module by its edges. CAUTION • Leave the memory module in the anti-static container until you are ready to install it. • Always use an anti-static wrist strap and a grounding mat.
Chapter 4 Installing Additional Memory 9. Align the notches on the DIMM with the keys on the slot. See Figure 4-3. Retaining Latches (2) Keys Notches DIMM Slot 30 Degrees Figure 4-3. Aligning the DIMM 10. Hold the DIMM at approximately 30 ° to the system board and press the DIMM firmly and evenly into the slot until the retaining latches close. See Figures 4-3 and 4-4.
Chapter 4 Installing Additional Memory 0 1 DIMM Slots 2 3 System Board Figure 4-4. Inserting DIMMs Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a defective DIMM. 1. Log off all users, back up files, and power down the HP Netserver. For detailed instructions, see "Powering-Down the HP Netserver," in Chapter 1, "Controls, Ports and Indicators." 2. Pull out the anti-tip foot at the bottom of the rack.
Chapter 4 Installing Additional Memory 5. Remove the air flow guide. See Figure 4-1. Refer to "Removing the Rear Chassis Blower/Bracket and Air Flow Guide" in Chapter 2, "Opening and Closing the HP Netserver." 6. Locate the DIMM slots on the system board. See Figure 4-2. 7. Open the retaining latches. 8. Lift the DIMM completely away from the slot. 9. Place the DIMM in its anti-static container. 10. Repeat Steps 6-9 for as many DIMMs as you need to remove.
5 Installing Additional Boards Introduction The HP Netserver LP 2000r provides three 64-bit PCI slots connected to a riser board contained in the PCI card cage. The slots will accept full-length 32-bit or 64-bit PCI accessory boards.
Chapter 5 Installing Additional Boards Accessory Board Installation Guidelines The following sections provide guidelines for installing PCI accessory boards into the HP Netserver LP 2000r. IRQ Settings The HP Netserver uses the Plug and Play feature of the PCI board to automatically assign IRQ settings to its resources. Boot Priority The HP Netserver's boot priority (BIOS search order for a boot drive) should be considered when selecting a boot device.
Chapter 5 Installing Additional Boards Remote Control Card The HP Netserver LP 2000r supports the HP Remote Control card, which uses the HP TopTools remote management software. The Remote Control card requires an I2C connection to the system board, provided by the I2C connector on the daughter board (Integrated Remote Assistant circuitry) that is installed on the system board. See Figure 5-1 and Figure 5-2.
Chapter 5 Installing Additional Boards Integrated RA Board 2 IC Connector Figure 5-2. Integrated RA Board Location Installing an Accessory Board Use this procedure to install the accessory board. NOTE For information about a specific PCI board type, refer to the Readme file, Tested Products List, or Configuration Advisor on your HP Netserver Navigator CD-ROM. 1. Log off all users and, if necessary, back up files.
Chapter 5 Installing Additional Boards 2. Press the power switch on the HP Netserver control panel to turn off power when prompted by the operating system. 3. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP Netserver chassis out from the rack as far as it can be extended. It is not necessary to remove the HP Netserver from the rack to install an accessory board. 4. Disconnect the power cables and any external cables connected to the system.
Chapter 5 Installing Additional Boards Lift Cage by Fan and Back Edge Figure 5-3. Removing the PCI Card Cage 8. Install the PCI card: a. Use a Phillips screwdriver to remove the slot cover. See Figure 5-4. b. Slide the PCI card into the PCI slot. See Figure 5-5. NOTE 44 Slot 1 does not support the HP NetRAID-4M PCI board. Avoid using slot 1 for full-length cards. Slots 2 and 3 may be used for any card.
Chapter 5 Installing Additional Boards Slot 3 Slot 2 Slot 1 Figure 5-4.
Chapter 5 Installing Additional Boards Figure 5-5. Inserting a PCI Card 9. When you have completed the PCI card installation, replace the PCI card cage and reconnect the card cage fan to the system board: a. Align the PCI card cage with the guides on the and left side of the chassis. Lower the PCI card cage and plug the fan into the connector on the system board. See Figure 5-6. b. Press down on the top of the card cage to plug the riser card into the motherboard. c.
Chapter 5 Installing Additional Boards Guide Pin Figure 5-6. Replacing the PCI Card Cage 10. Replace the top cover on the HP Netserver and push the Netserver back into the rack. Once the HP Netserver is returned to normal operation, you may need to install software drivers. The drivers for the new PCI board are either part of your existing system software or included on a flexible diskette or CD-ROM provided with the accessory board.
6 Installing an Additional Processor Introduction The HP Netserver LP 2000r ships with at least one processor installed. Both primary and secondary processor sockets are located on the system board (the primary socket is CPU 1). The voltage regulator modules (VRMs) are embedded in the system board. Tools Required The following tools are required to access, install, or remove the processors: • ¼-inch flat blade screwdriver • An anti-static service kit (3M 8501/8502/8503 or equivalent).
Chapter 6 Installing an Additional Processor Primary Processor (CPU1) Secondary Processor (CPU 2) Figure 6-1. System Board (top view) Installing a Second Processor This section provides the instructions for installing a second processor and its heatsink on the system board. Figure 6-1 indicates the location of the primary and secondary processors.
Chapter 6 Installing an Additional Processor CAUTION Take the following precautions when installing processors: • Leave the processor in the anti-static bag until you are ready to install it. • Wear an anti-static wrist strap and use a static-dissipating work surface or grounding mat connected to the chassis when handling components. • Before removing a processor from the anti-static bag, touch a grounded, unpainted metal surface to discharge static electricity. 1.
Chapter 6 Installing an Additional Processor 6. Ensure the processor speed of the second processor (CPU 2) is the same as the primary processor. If you are upgrading the second processor to a faster processor speed than the primary processor, the primary processor must also be changed. Both processors must have the same product number, which includes the same clock speed, cache size, and FSB speed. The supported processors only perform at the rated speed indicated on the processor in the HP Netserver.
Chapter 6 Installing an Additional Processor Terminator ZIF Lever Processor Socket Figure 6-2. Removing the Terminator NOTE Keep the terminator for future use. The terminator must be installed in the secondary processor socket when only one processor is used or the HP Netserver will not operate properly. 8. Align the second processor over the empty processor socket, as shown in Figure 6-3.
Chapter 6 Installing an Additional Processor CAUTION Ensure that you the align pin-1 of the processor with pin-1 of the processor socket or pin damage will occur. 9. Insert the second processor into the socket and close the ZIF lever to fully seat the processor. You should hear the ZIF lever click when it closes properly. NOTE No speed switch settings are required for the supported 1.13 and 1.26 GHz processors.
Chapter 6 Installing an Additional Processor Installing the Heatsink After installing a new processor, you need to install a heatsink on top of the processor. The thermal patch on the bottom of the heatsink provides thermal bonding between the two components. The patch must be replaced if the heatsink is removed (even temporarily) from the processor. 1. Remove the heatsink from the shipping container. 2. Inspect the thermal patch. Replace the patch if it is damaged: a.
Chapter 6 Installing an Additional Processor Thumb Latch Hook Latch (hidden) Step A Tab Tab Processor Socket Figure 6-4.
Chapter 6 Installing an Additional Processor Hold Down Hook Latch Tool Latch Figure 6-5. Setting the Latches Firmware and Software Changes This section deals with the firmware changes provided by the HP Netserver Navigator CD-ROM and the possible reinstalling of the NOS to recognize the second processor. Upgrading the Firmware If your processor included a new HP Netserver Navigator CD-ROM, insert the CD into the HP Netserver LP 2000r CD-ROM drive and power on the Netserver.
Chapter 6 Installing an Additional Processor Removing a Processor and Heatsink Use this procedure to remove a processor and its heatsink (the heatsink must be removed before the processor). CAUTION Take the following precautions when removing processors: • Wear an anti-static wrist strap and use a static-dissipating work surface or grounding mat connected to the chassis when handling components.
Chapter 6 Installing an Additional Processor 3. Tilt the heatsink back towards the hook latch and release the hook latch. Then, lift the heatsink away from the processor and out of the Netserver. 4. Open the ZIF lever to allow removal of the processor. See Figure 6-2. 5. Hold the processor by its edges and lift it out of the socket. Place it on a staticdissipating work surface or into an anti-static bag. 6.
7 Rack Mounting the HP Netserver (4-Post) Introduction This chapter provides instructions for mounting the HP Netserver in 4-post HP System/E or System/U racks (shown in Figure 7-1) and third-party non-threaded 4-post racks. If you have the older 4-post HP Systems rack, see Chapter 13, "Alternative Rack Mounting (4-Post)," for instructions. If you have a 2-post non-HP rack, see Chapter 8, "Rack Mounting the HP Netserver (2-Post)," or refer to the documentation in the appropriate rack accessory kit.
Chapter 7 Rack Mounting the HP Netserver (4-Post) b c a Characteristics of System E and System U racks: a. 5-Cornered Columns b. Full Panel Vent c. “HP Rack System/E” or “HP Rack System/U” Nameplate. d. Numbered EIA Units e. Anti-tip Foot extends in front or back (on System E Rack) d e Figure 7-1. HP System/E and System/U Rack Features The HP Netserver LP 2000r rack mount kit requires two EIA units of space in the rack.
Chapter 7 Rack Mounting the HP Netserver (4-Post) HP Netserver Rack Mount Parts List Ensure the rack-mounting kit provided with the HP Netserver contains the following parts: Table 7-1. Parts for Rack Mount Kit Quantity 2 Description Slide mechanisms Rack Configuration Tools The HP rack configuration tools (including white papers) are on HP's web site at the following URL: http://www.hp.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Safety Precautions Always keep the following safety and environmental issues in mind, especially if you install the HP Netserver in a non-HP rack environment: • Optimum Operating Environment - The optimum operating conditions for the HP Netserver is in an environmental controlled computer room with a temperature range of 20 to 22°C (68 to 72°F) at 40 to 60% relative humidity.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Marking Rack Columns To make it easier to install the slides in the rack, you may want to mark the rack columns to indicate the server placement. Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver. The tools are available at: http://www.hp.com/netserver/support Use a marking pen or masking tape to mark the server position on the face of the front columns and the inside of the rear columns.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Installing Slides in the Rack 1. Ensure the rack is stabilized. For HP system /E or /U racks, pull the anti-tip foot forward out of the bottom of the rack and lower the leveler screws to make firm contact with the floor. See Figure 7-3. Anti-tip Foot Extended Leveler Screws (4) Figure 7-3. Installing Slides in the Rack 2. Insert the rear slide mounting pins into holes you have marked on the rear column.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Removing Slides from the Rack Follow these steps if you need to release the outer slide assembly after it is installed in the rack. 1. Place your finger inside the slide to release the spring tab, as shown in the example in Figure 7-4. 2. Press in on the spring tab and pull the outer slide assembly toward you at the front of the rack. Spring Tab Figure 7-4.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Mounting the HP Netserver on the Slides Follow these steps to mount the HP Netserver on the slides in the rack. Once the Netserver is in the rack, you can connect the cables to the rear of the Netserver. NOTE WARNING If other rack components are to be mounted in the rack below the HP Netserver, install them before mounting the Netserver.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Figure 7-5.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Figure 7-6. Pressing the Stop Release Attaching the Front Bezel 1. Hook the bottom edge of the bezel onto the pins at the front of the chassis. See Figure 7-7. 2. Close the bezel and press the top corners to snap it into place.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Pin A B Pin Figure 7-7. Attaching the Bezel Cabling Rack Components After installing the HP Netserver in the rack, refer to the white paper entitled HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r) to cable the components in the rack enclosure. The white paper is available on HP's web site at the following URL: http://www.hp.
Chapter 7 Rack Mounting the HP Netserver (4-Post) Attaching the Cable Management Arm The Cable Management Arm (CMA) allows the cables and power cord to move in and out with the HP Netserver chassis without being accidentally disconnected. The Cable Management Arm installation is tool-less. 1. Ensure the HP Netserver is pushed all the way into the rack. 2. Attach the Cable Management Arm to the rack: a. Mount the outer flange of the Cable Management Arm on the pins on the left slide rear bracket. b.
Chapter 7 Rack Mounting the HP Netserver (4-Post) 3. Attach the Cable Management Arm to the HP Netserver: a. Insert the thumbscrew on the inner flange of the Cable Management Arm into the hole in the chassis slide mount. b. Tighten the thumbscrew to secure the Cable Management Arm. See Figure 7-8. 4. Extend the HP Netserver out of the rack to ensure the Cable Management Arm moves with the chassis without binding. 5.
8 Rack Mounting the HP Netserver (2-Post) Introduction This chapter provides instructions for mounting the HP Netserver in a two-post non-HP rack. The illustration below shows the characteristics of the 2-post (CPI – Chatsworth Products Inc.) rack. If you have the 4-post HP System/E or System/U rack, or a third-party 4-post rack, see Chapter 7, "Rack Mounting the HP Netserver (4-Post)," for instructions. If you have the older 4-post HP systems rack, see Chapter 13, "Alternative Rack Mounting.
Chapter 8 Rack Mounting the HP Netserver (2-Post) B A Characteristics of 2-Post Rack: A. U-shaped column for easy access B. Top is secured to ceiling to hold additional weight. C. Base is bolted to floor. C Figure 8-1.
Chapter 8 Rack Mounting the HP Netserver (2-Post) The HP Netserver LP 2000r rack mount kit requires two EIA units of space in the rack. Before mounting the Netserver, plan the Netserver's location in the rack relative to other rack components. Proper placement is vital both for safety and operating efficiency. For more information, see “Rack Configuration Tools” later in this chapter.
Chapter 8 Rack Mounting the HP Netserver (2-Post) The white papers, particularly the HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r), provide rack information for HP Netservers in high-density racks and additional information for rack systems not listed in this manual. You will need this information to complete a rack system installation.
Chapter 8 Rack Mounting the HP Netserver (2-Post) Marking the Columns To make it easier to mount the HP Netserver in the rack, you may want to mark the column holes that will be used by the Netserver. The Netserver may be mounted using either flush-mount or center-mount brackets that attach to the front side of the two columns. Use a marking pen or masking tape to mark the columns. Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver.
Chapter 8 Rack Mounting the HP Netserver (2-Post) Preparing the HP Netserver Before the HP Netserver can be mounted in the rack, you need to remove the factory-installed chassis slides from the Netserver and install the flush-mount or center-mount brackets. 1. Lay the HP Netserver on a flat surface. 2. Remove the slides from the sides of the chassis. See Figure 8-3. Figure 8-3. Removing Existing Hardware 3.
Chapter 8 Rack Mounting the HP Netserver (2-Post) 5. Attach the appropriate mounting brackets to the chassis, using the four screws provided for each bracket: a. If you are flush-mounting the HP Netserver, attach the two flush-mount brackets, as shown in Figure 8-4. b. If you are center-mounting the HP Netserver, attach the two center-mount brackets, as shown in Figure 8-5. NOTE The flush-mount brackets have pins for connecting the front bezel; the center-mount brackets do not have pins. Figure 8-4.
Chapter 8 Rack Mounting the HP Netserver (2-Post) Figure 8-5. Attaching Center-Mount Brackets Mounting the HP Netserver in the Rack Follow these steps to mount the HP Netserver in the rack and secure it in place. Once that is done, you can connect the front bezel to the Netserver chassis and attach cables. NOTE WARNING If other rack components are to be mounted in the rack below the HP Netserver, install them before mounting the Netserver. The HP Netserver LP 2000r weighs 38 lbs. (17.3 kg.
Chapter 8 Rack Mounting the HP Netserver (2-Post) 3. Insert a screw through the bottom hole on each bracket and tighten the screws sufficiently to hold the HP Netserver in place while you insert and tighten the remaining screws. See Figure 8-6 or Figure 8-7. Figure 8-6.
Chapter 8 Rack Mounting the HP Netserver (2-Post) Figure 8-7.
Chapter 8 Rack Mounting the HP Netserver (2-Post) Attaching the Front Bezel The bezel attaches to the brackets on the front of the HP Netserver. 1. Hook the bottom edge of the bezel onto the pins on the brackets. See Figure 8-8 (figure shows flush-mount brackets). 2. Close the bezel and press the top corners to snap it into place. Pin A Pin B Figure 8-8.
9 Connecting the Monitor, Keyboard, Mouse, and Power Supplies Introduction Use the procedures in this chapter to connect the peripheral devices to the HP Netserver LP 2000r, and install or remove the power supply module. Connecting the Monitor, Keyboard and Mouse 1. Connect the monitor, keyboard, and mouse to the HP Netserver LP 2000r using the connections provided on the rear of the chassis. See Figure 9-1. The two USB connectors are reserved for peripherals other than the keyboard or mouse.
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS Installing a Power Supply Module The HP Netserver LP 2000r comes with one power supply module. A second power supply module for redundancy is optional. If only one power supply module is used, it must be installed in power supply bay 2, and a power supply filler panel must be installed in the empty bay 1. Each power supply has its own power cord (see Figure 9-2).
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS Figure 9-3. Removing the Power Supply Filler Panel 2. Before installing the new power supply module, pinch the release and pull it down. See Figure 9-4. NOTE The release lever on the power supply module must be in the down position in order to install the module.
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS Release Lever Figure 9-4. Moving Release Lever Down 3. Slide the module into the power bay and press the release lever in until it clicks into place. See Figure 9-5. Figure 9-5. Installing a Power Supply Module 4. Plug in the power cord for the power supply module. See Figure 9-2.
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS Removing a Power Supply Module If only one power supply module is used, it must be installed in power supply bay 2, and a power supply filler panel must be inserted in the empty bay 1. CAUTION Operating the HP Netserver without a power supply filler panel in an empty power supply bay could cause excessive EMI or thermal damage to the Netserver. 1.
Chapter 9 Connecting the Monitor, Keyboard, Mouse, and UPS 2. If you are not replacing the power supply module, insert the power supply filler panel into the empty power supply bay: a. Pinch the release lever on the filler panel and pull the lever down. b. Slide the filler panel into the power bay. See Figure 9-7. c. Press the release lever in until it clicks into place. Figure 9-7. Inserting the Power Supply Filler Panel Connecting the Uninterruptible Power Supply 1.
10 Configuring the HP Netserver Introduction This chapter describes how to configure the HP Netserver LP 2000r with the help of the HP Netserver Navigator CD-ROM, which is shipped with your Netserver. This CD-ROM also provides the latest information concerning your Netserver. As you configure the Netserver, it's important to have the very latest configuration information.
Chapter 10 Configuring the HP Netserver Contents of the HP Netserver Navigator CD-ROM The Main Menu of the Navigator CD directs you to modules where you can perform the required configuration tasks, or access the utilities used in the configuration process.
Chapter 10 Configuring the HP Netserver Status Report Identification You must compare the Document Number on your HP Netserver Navigator CD with the most current Status Report's Document Number for your HP Netserver model. • Each Status Report has a different Document Number. You can obtain the release history (archive) and Status Report for your CD-ROM through the Web: • Internet WWW -- http://netserver.hp.com/netserver/support/ Once on the web site, select from the following items: 1.
Chapter 10 Configuring the HP Netserver • HP TopTools Remote Control Card – This is an accessory PCI board that provides a connection for remote LAN or modem-based server management software (HP TopTools) when installed into the Netserver. • Integrated Remote Assistant – This is an embedded product called HP Integrated Remote Assistant (also referred to as Integrated RA).
Chapter 10 Configuring the HP Netserver Accessing the Setup Utility The (BIOS) Setup Utility menu offers the choices listed above, and the corresponding items are described in the topics below. 1. Turn on the monitor and the HP Netserver. 2. Start the Setup Utility by pressing the [F2] key, when the following message appears on the boot screen. Press to enter SETUP Menu Bar The Setup Utility provides a menu bar with several menu selections.
Chapter 10 Configuring the HP Netserver o Embedded LAN Controllers - Enable or disable the embedded LAN controllers and the available features. The Alert-On-LAN 2 (AOL2) and Wake-on-LAN features are enabled/disabled under the embedded LAN A submenu. o Boot Device Ordering - Set the boot order, including bootable boards. • Exit – Exit the Setup Utility by saving changes or exit without saving changes, which reverts to previous settings. When you exit, the HP Netserver reboots.
Chapter 10 Configuring the HP Netserver Once in the Setup Utility, the menu bar appears at the top of the screen with "User Preferences, Security, Configuration, and Exit" shown. The User Preferences menu is the default menu and should be the highlighted selection at the left of the menu bar when the Setup Utility first opens. 3. If necessary, use the up-arrow key to move to the System Time field. The "System Time" field is highlighted by default when the "User Preferences" menu is selected.
Chapter 10 Configuring the HP Netserver 2. Use the right-arrow or left-arrow key to select Security from the menu bar. As soon as it is selected, the selections for the Security menu appear as shown below. ➢Power-On Password ➢Hardware Security The arrowhead ➢ indicates there is a submenu to select from. 3. If necessary, use the arrow key to move to the Power-On Password menu selection and press Enter. The Power-On Password is highlighted by default when the Security menu is selected.
Chapter 10 Configuring the HP Netserver 5. Enter the password (new or old) in the appropriate field and press Enter. The password is accepted and the next field just below it, "Re-enter new password: [ ]" or "Enter new password: [ ]" field is highlighted. For security reasons, the password does not appear on the screen. 6. Enter the new password in the "Enter new password: [ NOTE ]" field.
Chapter 10 Configuring the HP Netserver To access the Symbios SCSI Configuration Utility, refer to the following instructions. 1. Reboot the HP Netserver. If you are already in the boot process, you should see the following message appear. Press to start Symbios Configuration Utility... 2. Press + keys to enter the utility. 3. Use the arrow keys to move the cursor, press Enter to select an option, and press Esc to exit. 4. To change adapter settings: a.
11 HP Netserver Online Documentation CD-ROM Overview The HP Netserver Online Documentation CD-ROM contains the entire set of documentation for your HP Netserver LP 2000r.
12 Troubleshooting Introduction If you are having problems installing your HP Netserver, there are a number of tools available for troubleshooting, including the information provided in this chapter.
Chapter 12 Troubleshooting Common Installation Problems The following sections contain general procedures to help you locate installation problems. If you need assistance, HP recommends contacting your reseller first. If you need to get assistance from Hewlett-Packard, refer to the Warranty and Support document provided with the Netserver. WARNING Before removing the cover, always disconnect the power cord and unplug telephone cables.
Chapter 12 Troubleshooting Netserver Will Not Power On Follow these steps if the power/activity light does not light green after you press the power-on button, or the Netserver will not power on properly. NOTE If the heatsink is not properly installed on the processor, the processor may overheat, causing intermittent or unreliable operation which may lead to a system crash and permanent damage to the processor. 1. Remove the AC power cord, wait 15 seconds, reconnect the power cord, and try again. 2.
Chapter 12 Troubleshooting For example, reduce the Netserver to the monitor, one flexible disk drive, one CD-ROM drive, one SCSI hard disk drive, keyboard, mouse, and one NIC. 4. Power on the Netserver to start the boot process. 5. If the Netserver will not complete the boot process: a. Consult the troubleshooting steps in the section "Hardware Problems" later in this chapter. b. If you get an error message or beep code refer to the HP Netserver LP 2000r Service Manual on the HP Web site at: http://www.
Chapter 12 Troubleshooting 10. Choose the Exit option and save the changes to save the configuration and exit the Setup Utility. Battery Spring Latch (Back of Chassis) Switch 1 Position Configuration Switch Figure 12-1. Configuration Switch Location Shaded rectangle represents the position of the switch.
Chapter 12 Troubleshooting Resetting a Lost Password If you have forgotten the Power-on password, you can reset it using the configuration switch on the system board. NOTE If you have forgotten the Power-on password, your Netserver will function normally, but you will not be able to access the configuration settings in the Setup Utility or complete the boot process if you reboot the Netserver. 1. Turn off power to the HP Netserver. 2. Remove the cover. 3.
Chapter 12 Troubleshooting Hardware Problems This section describes what to do if you have problems with your monitor, mass storage devices, printer, accessory boards, keyboard, or mouse. Monitor Does Not Work NOTE If the Netserver has a large amount of memory installed, it may take 30 seconds for the first screen to display. 1. If nothing is displayed on the screen, but the Netserver starts and you have verified the keyboard, disk drives, and other peripheral devices are functioning properly: a.
Chapter 12 Troubleshooting Keyboard or Mouse Does Not Work 1. Verify the keyboard and mouse are connected to the correct connectors. Refer to the I/O panel label on the rear panel of the Netserver. 2. Verify the mouse is correctly defined in the control options of your NOS. 3. Clean the mouse ball and rollers using a lint-free cloth. CD-ROM Drive Does Not Work 1. Verify a CD is inserted in the drive. 2. Verify the power and data cables are correctly connected to the device. 3.
Chapter 12 Troubleshooting Replacing a Battery If your HP Netserver repeatedly loses its configuration or the processor clock stops, you should replace the battery. WARNING There is danger of explosion if the battery is incorrectly installed. For your safety, never attempt to recharge, disassemble, or burn the old battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 1.
Chapter 12 Troubleshooting Figure 12-3. Battery on System Board 7. Insert the new battery with the positive sign (+) facing up. Push the battery down into the socket. The battery should snap into place. Ensure the spring latch holds the battery firmly. 8. Replace the PCI card cage, processor cooling fan, and cover. 9. Power on the Netserver. 10. Press to run the Setup Utility and reset the CMOS settings. Refer to “Setup (BIOS) Utility” in Chapter 10, "Configuring the HP Netserver.
13 Alternative Rack Mounting (4-Post) Introduction This chapter provides the instructions for mounting the HP Netserver in an older 4-post HP Systems rack, as shown in Figure 13-1. If you have the newer 4-post HP System/E or System/U rack or a third-party non-threaded 4-post rack, see Chapter 7, "Rack Mounting the HP Netserver (4-Post).
Chapter 13 Alternative Rack Mounting (4–Post) B A Characteristics of HP System rack: D E Figure 13-1. HP System Rack 116 A. 3-Cornered columns B. Fan-Only Vent C. “HP systems” name Plate D. EIA Units Marked by Triangles E.
Chapter 13 Alternative Rack Mounting (4–Post) The HP Netserver LP 2000r rack mount kit requires two EIA units of space in the rack. Before mounting the Netserver, plan for the Netserver's location in the rack relative to other rack components. Proper placement is vital both for safety and operating efficiency. For more information, see “Rack Configuration Tools” later in this chapter. Tools Required The following tools are required to rack-mount the HP Netserver.
Chapter 13 Alternative Rack Mounting (4–Post) The white papers, specifically HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r), provide rack information for HP Netservers in the high density racks and additional information for rack systems not listed in this manual. You will need this information to complete a rack system installation.
Chapter 13 Alternative Rack Mounting (4–Post) Marking the Columns To make it easier to install the slides in the rack, you may want to mark the columns to indicate the server placement. Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver. The tools are available at the following URL: http://www.hp.com/netserver/support Use a marking pen or masking tape to mark the server position on the inside of the front and rear columns, as shown in Figure 13-2.
Chapter 13 Alternative Rack Mounting (4–Post) Installing the Slides in the Rack 1. Prepare both slides for installation: a. Remove the spring from the slide’s rear bracket. See Figure 13-3. b. Remove the nuts holding the front and rear slide brackets and remove the brackets from the slides. Save the nuts. You will use them in Step 3. Figure 13-3.
Chapter 13 Alternative Rack Mounting (4–Post) 2. Attach the brackets to the front columns, using the two screws provided in the hardware kit. See Figure 13-4. Figure 13-4. Attaching the Front Brackets to the Rack 3. Install the slides in the rack: a. Insert the slide into the rack at the location you have marked on the front and rear columns. The slide bolts insert into the 2nd hole, counting from the base of the HP Netserver.
Chapter 13 Alternative Rack Mounting (4–Post) b. Tighten the nuts (saved from Step 1) onto the slide bolts to secure the slides to the columns. Use the M10 socket Torx driver to tighten the nuts. See Figure 13-5. Figure 13-5.
Chapter 13 Alternative Rack Mounting (4–Post) Mounting the HP Netserver on the Slides Use this procedure to insert the HP Netserver into the slides mounted in the rack. Once the Netserver is in the rack, you can connect the cables to the rear of the Netserver.
Chapter 13 Alternative Rack Mounting (4–Post) Figure 13-6.
Chapter 13 Alternative Rack Mounting (4–Post) Figure 13-7. Pressing the Stop Release Attaching the Front Bezel 1. Position the bezel in front of the HP Netserver LP 2000r, as shown in Figure 13-8. 2. Hook the bottom edge of the bezel onto the chassis pins. 3. Close the bezel and press the top corners to engage the spring latches. The spring latches should click when engaged.
Chapter 13 Alternative Rack Mounting (4–Post) Pin A B Pin Figure 13-8. Attaching the Bezel to the HP Netserver Cabling Rack Components After installing the HP Netserver in the rack, refer to the white paper entitled HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r) to cable the components in the rack enclosure. The white paper is available on HP's web site at the following URL: http://www.hp.
Chapter 13 Alternative Rack Mounting (4–Post) Attaching the Cable Management Arm The Cable Management Arm (CMA) allows the cables and power cord to move in and out with the HP Netserver chassis without being accidentally disconnected. The Cable Management Arm installation is tool-less. 1. Ensure the HP Netserver is pushed all the way into the rack. 2. Attach the Cable Management Arm to the rack: a.
A Specifications Introduction This appendix provides the power requirements, operating conditions (environmental requirements), physical requirements, hardware specifications, and video resolutions of the HP Netserver LP 2000r. The system board layout and the unused connectors are also provided. See Figures A-1 and A-2. Requirements The following tables provide the specifications required for normal operation of the HP Netserver LP 2000r. Table A-1.
Appendix A Specifications Table A-2. Environmental Requirements Parameter Conditions Temperature Operating 5° to 35° C (41° to 95° F) NOTE • Subtract 1° C (2° F) from the maximum temperature for each 609m (2,000 ft.
Appendix A Specifications Table A-3. Weight and Dimensions Weight___________ 38 lbs. (17.3 kg.) fully loaded (6 SCSI HDDs, 2 processors, and 4 DIMMs); excludes keyboard, mouse, and monitor Height ___________ 3.36 inches (85.4 mm) Width____________ 16.8 inches (428 mm) Depth 23.3 inches (591 mm) Table A-4. HP Netserver Hardware Specifications Processors Intel Pentium III (up to 2 processors) processors, at supported speeds of 1.13 and 1.26 GHz, with 512 KB level 2 cache on processor.
Appendix A Specifications Table A-5. Video Display Modes Resolution Max. Refresh Rate @ 256 Colors Max. Refresh Rate @ 65K Colors Max. Refresh Rate @ 16.
Appendix A Specifications Not Used Wake-onLAN (WOL) Not Used PCI Board Fan Wake-onRing (WOR) Not Used Not Used Power Supply Speed Monitor Integrated RA Board Connectors (2) (Daughter Board) Not Used Memory Fan Processor (CPU) Fan Power, Reset Buttons, Power LED Management Function Not Used See Default Settings Figure A-2.
Index A accessory board installing, 42 removing, 47 ACPI Advanced Configuration and Power Interface, 2, 7 Advanced Configuration and Power Interface ACPI, 7 air flow guide removing, 13 replacing, 14 anti-tip foot rack installation, 66, 68 B boot device order Setup Utility, 98 boot device priority boot order, 19 changing boot order, 101 boot order boot device priority, 19 CD-ROM, 19 CD-ROM, 40 default, 19 flexible disk drive, 19 flexible disk drive, 40 modifying, 20 Network connection, 40 PCI slot, 40 PCI sl
Index DIMMs installation guidelines, 32 installing, 31, 32 non-compatible, 31 open slot configuration, 32 removing, 36 retaining latches, 37 slots 0 through 3, 32 supported memory capacity, 32 Disk Array Controller board HP NetRAID 4M, 40 recommendation, 40 Diskette Library, 105 display modes, 132 Drive Array Controller (DAC), 20 drive types supported flexible disk drive, 17 IDE CD-ROM, 17 low-voltage differential SCSI, 18 Ultra-160M SCSI hard drives, 18 drives installing, 18 E embedded LAN controller LAN
Index HP Netserver Online Documentation CD-ROM, 103 automatic start, 103 I I2C connector supported, 41 IDE device Setup Utility, 97 IDE Setup Utility, 97 indicator LEDs, 2 ON/OFF, 2 inrush current allowing for, 7 installing additional memory, 32 DIMMs, 32 heatsink, 55 integrated I/O port Setup Utility, 97 Integrated Remote Assistant, 96 IRQ settings automatically assigned, 40 K keyboard, 87 troubleshooting, 112 L LAN LEDs, 5 RJ45 port, 5 speed 10 Mbps, 5 speed 100 Mbps, 5 LAN A Power On/Off Magic Packet, 9
Index keyboard, 4 LAN port, 4 mouse, 4 ports external, 87 keyboard, 87 mouse, 87 parallel, 4 rear panel, 4 serial ports, 87 USB ports, 87 video, 4, 87 power management Sleep States, 8 power management (ACPI) LAN A Power On/Off, 96 Wake-on-LAN, 96 Power requirements, 129 power supply module installing, 87 removing, 87 power switch DC power (front panel), 2 powering-down procedure, 6 powering-on procedure, 6 Power-on password setting, 101 problems CD-ROM drive, 112 keyboard, 112 mouse, 112 processors firmwar
Index Exit menu, 98 flexible disk drive, 97 hardware security, 97 IDE devices, 97 IDE primary/secondary, 97 integrated I/O port, 97 LAN A Power On/Off, 96 making selections, 98 memory cache, 97 menu bar, 97 password, 97 PCI slot devices, 97 pressing F2 to enter, 97 resetting lost password, 100, 101 security, 97 setting boot password, 99 user preferences, 97 Wake-on-LAN, 96 site preparation environmental considerations, 130 Sleep States, 2 Advanced Configuration and Power Interface, 7 defined, 7 hibernate,
Index Wake-on-LAN Magic Packet, 96 weight, 131 weight and dimensions, 131 140 Z Zero Insertion Force ZIF, 52 ZIF Zero Insertion Force, 52