HP ProLiant BL20p Generation 4 Server Blade User Guide Part Number 405591-002 December 2006 (Second Edition)
© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Contents Component identification ............................................................................................................... 6 Server blade components ........................................................................................................................... 6 Front panel components ................................................................................................................... 6 Front panel LEDs........................................................
Accessing local media devices ........................................................................................................ 35 Configuration and utilities ............................................................................................................ 37 Server blade deployment tools .................................................................................................................. 37 Software drivers and additional components ..........................................
Battery replacement .................................................................................................................... 68 Regulatory compliance notices ..................................................................................................... 69 Regulatory compliance identification numbers ............................................................................................. 69 Federal Communications Commission notice.......................................................
Component identification In this section Server blade components .......................................................................................................................... 6 Local I/O cable ..................................................................................................................................... 12 Server blade enclosure bay numbering ..................................................................................................... 12 iLO 2 connections ........
Front panel LEDs Item Description Status 1 UID LED Blue = Identified Blue flashing = Active remote management Off = No active remote management 2 Health LED Green = Normal Green flashing = Booting Amber = Degraded condition Red = Critical condition 3 NIC 1 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 4 NIC 2 LED* Green = Network linked Green flashing = Network activity Off = No link or activity 5 NIC 3 LED* Green = Network linked Green flashing =
Item Description Status 9 Drive activity Green = Active online condition Off = Inactive online condition * Actual NIC numeration depends on several factors, including the operating system installed on the server blade.
Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (green) SAS and SATA hard drive LED combinations Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation On, off, or flashing Alternating amber and blue The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application. On, off, or flashing Steadily blue The drive is operating normally, and it has been selected by a management application.
Internal components Item Description 1 HP Smart Array SAS/SATA Battery-Backed Write Cache enabler (optional) 2 Internal USB connector 3 SAS backplane power connectors (2) 4 SAS backplane connectors (2) 5 Processor socket 2 6 HP Smart Array E200i Controller cache module connector 7 HP Smart Array E200i Controller cache module 8 HP Smart Array E200i Controller 9 FBDIMM slots 1-8 10 NMI switch 11 System battery 12 Power converter module 13 NIC mezzanine connector 14 System mainten
FBDIMM slots Item Description 1 FBDIMM slot 1A 2 FBDIMM slot 2C 3 FBDIMM slot 3A 4 FBDIMM slot 4C 5 FBDIMM slot 5B 6 FBDIMM slot 6D 7 FBDIMM slot 7B 8 FBDIMM slot 8D System maintenance switch Position Function Default 1* iLO 2 security override Off 2 Configuration lock Off 3 Reserved Off 4 Reserved Off 5* Password disabled Off 6* Reset configuration Off 7 Reserved Off 8 Reserved Off *To access redundant ROM, set S1, S5, and S6 to ON.
Local I/O cable Item Connector Description 1 Local I/O For connecting to the local I/O port on the server blade front panel 2 Video For connecting a video monitor 3 USB 1 For connecting a USB device 4 USB 2 For connecting a USB device 5 Serial For trained personnel to connect a null modem serial cable and perform advanced diagnostic procedures 6 iLO 2 RJ-45 (10/100 Ethernet) For connecting an Ethernet to the server blade iLO 2 interface from a client device Server blade enclosure bay n
IMPORTANT: When looking at the rear of the enclosure, server blade bay numbering is reversed. iLO 2 connections An iLO 2 connector resides on the server blade management module of the enhanced server blade enclosure. This RJ-45 connector enables remote manageability for each server blade in the enhanced server blade enclosure.
Blade Enclosure). For information on the compatibility of server blade enclosures, refer to the HP website (http://www.hp.com/go/bladesystem/enclosure/compatibility).
Operations In this section Power up the server blade....................................................................................................................... 15 Power down the server blade .................................................................................................................. 15 Remove the server blade ......................................................................................................................... 16 Remove the access panel .................
IMPORTANT: When the server blade is in standby mode, auxiliary power is still being provided. To remove all power from the server blade, remove the server blade from the server blade enclosure. IMPORTANT: Remote power procedures require the most recent firmware for the power enclosure and server blade enclosure management modules. For the most recent firmware, refer to the HP website (http://www.hp.com/go/support). Remove the server blade 4. Identify the proper server blade in the server blade enclosure.
6. Remove the access panel. Install the access panel 1. 2. Place the access panel on top of the server blade, allowing it to extend past the rear of the server approximately 10 mm (0.39 in). Slide the access panel forward to lock, and tighten the captive screw to secure the access panel to the server. Remove the air baffle To remove the component: 1. 2. 3. Power down the server blade (on page 15). Remove the server blade (on page 16). Remove the access panel (on page 16).
4. Remove the air baffle. To replace the component, reverse the removal procedure. IMPORTANT: To ensure proper cooling, be sure the correct processor air baffle is installed at all times.
Setup In this section Installing the HP BladeSystem components................................................................................................. 19 Verifying system components ................................................................................................................... 19 Connecting to the network....................................................................................................................... 19 Installing server blade options......................
Installing a server blade 1. Remove a 6U server blade blank. 2. Install the server blade. When the server blade is fully inserted, it locks into place. The default setting for server blades initiates automatic power up. CAUTION: To prevent improper cooling and thermal damage, do not operate the server blade enclosure unless all bays are populated with either a component or a blank.
Hardware options installation In this section Processor option..................................................................................................................................... 21 Memory option ...................................................................................................................................... 26 Hard drive option...................................................................................................................................
CAUTION: To prevent possible server blade overheating, always populate processor socket 2 with a processor and a heatsink or a processor cover and a heatsink blank. 5. Open the processor retaining latch and the processor socket retaining bracket.
6. Remove the processor socket protective cover. IMPORTANT: Be sure the processor remains inside the processor installation tool. 7. If the processor has separated from the installation tool, carefully re-insert the processor in the tool.
8. Align the processor installation tool with the socket and install the processor. 9. Press down firmly until the processor installation tool clicks and separates from the processor, and then remove the processor installation tool.
10. Close the processor socket retaining bracket and the processor retaining latch. 11. Remove the heatsink protective cover. 12. Align the holes in the bottom of the heatsink with the pins in the heatsink retention module.
13. Install the heatsink and close the heatsink retaining latch. Install the access panel (on page 17). 15. Install the server blade ("Installing a server blade" on page 20). 16. Power up the server blade (on page 15). 14. NOTE: By default, the server blade powers up on installation. Memory option The server blade ships with two FBDIMMs installed. The server blade supports up to 32 GB of memory. CAUTION: Use only HP FBDIMMs. FBDIMMs from other sources may adversely affect data integrity.
Installing FBDIMMs 1. 2. 3. 4. 5. Power down the server blade (on page 15). Remove the server blade (on page 16). Remove the access panel (on page 16). Open the FBDIMM slot latches. Install the FBDIMM. To remove FBDIMMs, reverse the installation procedure. For FBDIMM slots 1 and 2, remove the air baffle, if necessary. Refer to the instructions located on the air baffle. Hard drive option The server blade supports up to two hot-plug SFF SAS or SATA drives.
1. Remove the hard drive blank. 2. Open the release latch and prepare the hard drive for installation.
3. Install the hard drive. 4. Determine the status of the hard drive from the hot-plug hard drive LEDs. ("SAS and SATA hard drive LED combinations" on page 9, "SAS and SATA hard drive LEDs" on page 8) 5. Resume normal server operations. Multifunction network adapter option To install the component: 1. 2. 3. 4. 5. 6. 7. Back up all server blade data. Power down the server blade (on page 15). Remove the server blade (on page 16). Remove the access panel (on page 16).
8. Power up the server blade (on page 15). NOTE: By default, the server blade powers up on installation. Fibre Channel mezzanine option An optional dual port FC mezzanine enables FC support for clustering capabilities and SAN connection when used in conjunction with interconnect devices that support a SAN connection. For more information about connecting to the SAN, refer to “SAN configuration (on page 43)". Server blades can be configured for SAN connectivity when used with the following components.
Install the access panel (on page 17). 9. Install the server blade ("Installing a server blade" on page 20). 10. If connecting to SAN, install one of the interconnect device options ("Interconnect options" on page 31). 8. Interconnect options To connect to SAN using optical cables, you must install either an RJ-45 Patch Panel 2 or a SANcompatible interconnect option kit in the server blade enclosure.
5. Connect the cable to the cache module. 6. Install the access panel (on page 17). Install the server blade ("Installing a server blade" on page 20). Power up the server blade (on page 15). 7. 8. NOTE: By default, the server blade powers up on installation.
Local I/O cabling In this section Using the local I/O cable........................................................................................................................ 33 Local administration using iLO 2 .............................................................................................................. 33 Connecting locally to a server blade with video and USB devices ................................................................
2. Connect the local I/O cable to the I/O port on the server blade. CAUTION: Disconnect the local I/O cable when not in use. The port and connector do not provide a permanent connection. Rear iLO 2 connector performance degrades when the local I/O cable is connected, even if the iLO 2 connector on the cable is not in use. CAUTION: Before disconnecting the local I/O cable, observe the following guidelines: • • Completely log out of the current iLO 2 session before disconnecting from the iLO 2 port.
Connect the video connector to a monitor. Connect a USB mouse to one USB connector. Connect a USB keyboard to the second USB connector. 2. 3. 4. Item Description 1 Monitor 2 USB mouse 3 USB keyboard 4 Local I/O cable Accessing local media devices Use the following configuration when configuring a server blade or loading software updates and patches from a CD-ROM, such as the SmartStart CD, or a diskette. CAUTION: Disconnect the local I/O cable when not in use.
NOTE: Use a USB hub when connecting a USB diskette drive and/or USB CD-ROM drive to the server blade. The USB hub provides additional connections.
Configuration and utilities In this section Server blade deployment tools ................................................................................................................. 37 Configuration tools ................................................................................................................................. 44 Management tools..................................................................................................................................
• • • • Send alerts from iLO 2 Advanced regardless of the state of the host server blade. Access advanced troubleshooting features provided by iLO 2 Advanced. Launch a web browser, use SNMP alerting, and diagnose the server blade with HP SIM. Configure static IP bay settings for the dedicated iLO 2 management NICs on each server blade in an enclosure for faster deployment. The server blade must be properly cabled for iLO 2 connectivity.
o Ethernet NIC with 10/100 RJ-45 connector o TCP/IP networking and an IP address compatible with one of the following: the iLO 2 Diagnostic Port IP address or an assigned DHCP or static IP address o CD-ROM drive and/or diskette drive o Any of the following Java™ Runtime Environment versions: 1.3.1_02 1.3.1_07 1.3.1_08 1.4.1 for Windows® users only 1.4.2 for Linux users only Access the Java™ Runtime Environment versions at the HP website (http://java.sun.com/products/archive/index.html).
1.4.2 for Linux users only Access the Java™ Runtime Environment versions at the HP website (http://java.sun.com/products/archive/index.html). • Network server with an OS installed Static IP bay configuration Static IP bay configuration, implemented using the new Static IP Bay Settings on the BL p-Class tab, eases the initial deployment of an entire enclosure or the subsequent deployment of blades within an existing enclosure.
A number of third-party PXE deployment tools are available for Windows® and Linux. For additional information, refer to the HP website (ftp://ftp.compaq.com/pub/products/servers/management/pxe_wp.pdf). HP ProLiant Essentials Rapid Deployment Pack NOTE: To deploy server blades in an existing server blade enclosure, always use the most recent version of RDP available at the HP website (http://www.hp.com/servers/rdp). The RDP software is the preferred method for rapid, high-volume server deployments.
iLO virtual CD-ROM To deploy with a boot CD: 1. Do one of the following: o Insert the boot CD into the client PC that is using the iLO 2 Remote Console. o Use iLO 2 to create an image file of the boot CD. o Copy the image of the boot CD to a location on the network or the client PC hard drive. 2. Remotely access the server blade through iLO 2. Refer to "ProLiant p-Class Advanced management (on page 37)." 3. Click the Virtual Devices tab. Select Virtual Media.
Other methods for connecting to the server blade are available, but they do not provide the required network access for deployment. For more information, refer to "ProLiant p-Class Advanced management (on page 37)." NOTE: For more information about hardware and cabling configurations, refer to the documents that ship with the server blade enclosure or diagnostic station.
• The server blade enclosure management module firmware is up-to-date. Refer to the HP Business Support Center website (http://www.hp.com/support). • • The server blade is cabled properly to a supported SAN. SAN storage drivers are loaded. Refer to supporting white papers and the HP website (http://www.hp.com/servers/rdp). For SAN configuration information for the server blade, refer to the HP StorageWorks SAN Design Reference Guide on the HP website (http://h18000.www1.hp.
Using RBSU The first time you power up the server blade, the system prompts you to enter RBSU and select a language. Default configuration settings are made at this time and can be changed later. Most of the features in RBSU are not required to set up the server blade. To navigate RBSU, use the following keys: • To access RBSU, press the F9 key during power up when prompted in the upper right corner of the screen. • • To navigate the menu system, use the arrow keys.
BIOS Serial Console BIOS Serial Console allows you to configure the serial port to view POST error messages and run RBSU remotely through a serial connection to the server COM port. The server that you are remotely configuring does not require a keyboard and mouse. For more information about BIOS Serial Console, refer to the BIOS Serial Console User Guide on the Documentation CD or the HP website (http://www.hp.com/servers/smartstart).
WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified. This option should only be used by qualified service personnel. This value should always match the serial number sticker located on the chassis. Press the Enter key to clear the warning. 5. Enter the serial number and press the Enter key. 6. Select Product ID. 7. Enter the product ID and press the Enter key. 8. Press the Esc key to close the menu. 9.
For more information about iLO 2 features, refer to the iLO 2 documentation on the Documentation CD or on the HP website (http://www.hp.com/servers/lights-out). HP Systems Insight Manager HP SIM is a web-based application that allows system administrators to accomplish normal administrative tasks from any remote location, using a web browser. HP SIM provides device management capabilities that consolidate and integrate management data from HP and third-party devices.
• • DOS Operating environments which do not provide native USB support For more information on ProLiant USB support, refer to the HP website (http://h18004.www1.hp.com/products/servers/platforms/usb-support.html).
• From within HP Insight Diagnostics (on page 49) For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack. Remote support and analysis tools HP Instant Support Enterprise Edition ISEE is a proactive remote monitoring and diagnostic tool to help manage your systems and devices, a feature of HP support. ISEE provides continuous hardware event monitoring and automated notification to identify and prevent potential critical problems.
If you do not use the SmartStart CD to install an operating system, drivers for some of the new hardware are required. These drivers, as well as other option drivers, ROM images, and value-add software can be downloaded from the HP website (http://www.hp.com/support). IMPORTANT: Always perform a backup before installing or updating device drivers. ProLiant Support Packs PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management agents.
Troubleshooting In this section Troubleshooting resources ....................................................................................................................... 52 Pre-diagnostic steps ................................................................................................................................ 52 Service notifications................................................................................................................................ 55 Loose connections ......
Important safety information Before servicing this product, read the Important Safety Information document provided with the server. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • • • • • The leveling feet are extended to the floor. The full weight of the rack rests on the leveling feet. The stabilizing feet are attached to the rack if it is a single-rack installation. The racks are coupled together in multiple-rack installations. Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.
Prepare the server for diagnosis 1. 2. 3. 4. 5. 6. Be sure the server is in the proper operating environment with adequate power, air conditioning, and humidity control. Refer to the server documentation for required environmental conditions. Record any error messages displayed by the system. Remove all diskettes and CDs from the media drives. Power down the server and peripheral devices if you will be diagnosing the server offline. Always perform an orderly shutdown, if possible. This means you must: a.
Troubleshooting flowcharts To effectively troubleshoot a problem, HP recommends that you start with the first flowchart in this section, "Start diagnosis flowchart (on page 56)," and follow the appropriate diagnostic path. If the other flowcharts do not provide a troubleshooting solution, follow the diagnostic steps in "General diagnosis flowchart (on page 57).
General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the problem, or if the other flowcharts do not fix the problem, use the following flowchart.
Item See 4 The most recent version of a particular server or option firmware is available on the following websites: • • HP Support website (http://www.hp.com/support) HP ROM-BIOS/Firmware Updates website (http://h18023.www1.hp.com/support/files/server/us/romflash.ht ml) 5 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
Server blade power-on problems flowchart Symptoms: • • • The server does not power on. The system power LED is off or amber. The health LED is red or amber.
NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system attempts to access the boot device.
Possible problems: • • • Improperly seated or faulty internal component Faulty KVM device Faulty video device Item Refer to 1 "POST error messages and beep codes (on page 67)" 2 "Video problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
OS boot problems flowchart Symptoms: • • Server does not boot a previously installed OS Server does not boot SmartStart Possible causes: • Corrupted OS Troubleshooting 63
• • Hard drive subsystem problem Incorrect boot order setting in RBSU Item Refer to 1 HP ROM-Based Setup Utility User Guide (http://www.hp.com/servers/smartstart) 2 "POST problems flowchart (on page 61)" 3 • "Hard drive problems" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
Server fault indications flowchart Symptoms: • • Server boots, but a fault event is reported by Insight Management Agents (on page 48) Server boots, but the internal health LED, external health LED, or component health LED is red or amber NOTE: For the location of server LEDs and information on their statuses, refer to the server documentation.
Possible causes: • • • • Improperly seated or faulty internal or external component Unsupported component installed Redundancy failure System overtemperature condition Item Refer to 1 "Management agents (on page 48)" or in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support) 2 • "Integrated Management Log" or in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.
POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website (http://www.hp.com/support). WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary information in the server documentation before removing, replacing, reseating, or modifying system components.
Battery replacement If the server blade no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled.
Regulatory compliance notices In this section Regulatory compliance identification numbers ........................................................................................... 69 Federal Communications Commission notice ............................................................................................. 69 Declaration of conformity for products marked with the FCC logo, United States only..................................... 70 Cables ........................................................
Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • • • Do not attempt to recharge the battery. Do not expose the battery to temperatures higher than 60°C (140°F).
Regulatory compliance notices 74
Electrostatic discharge In this section Preventing electrostatic discharge............................................................................................................. 75 Grounding methods to prevent electrostatic discharge ................................................................................ 75 Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts.
Specifications In this section Environmental specifications .................................................................................................................... 76 Server specifications ...............................................................................................................................
Technical support In this section Before you contact HP............................................................................................................................. 77 HP contact information............................................................................................................................ 77 Customer Self Repair ..............................................................................................................................
• Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product. NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that an authorized service provider replace the part.
Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss mit der zugehörigen Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen.
dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee categorieën CSR-onderdelen: • Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening gebracht. • Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor reparatie door de klant.
reparo feito pelo cliente, a HP paga todas as despesas de transporte e de devolução da peça e determina a transportadora/serviço postal a ser utilizado. Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP (http://www.hp.com/go/selfrepair).
Technical support 83
Technical support 84
Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility ASR Automatic Server Recovery BBWC battery-backed write cache BIOS Basic Input/Output System DDR double data rate DHCP Dynamic Host Configuration Protocol DNS domain name system ESD electrostatic discharge FBDIMM fully buffered DIMM FC Fibre Channel FCA Fibre Channel adapter Acronyms and abbreviations 85
I/O input/output IEC International Electrotechnical Commission iLO 2 Integrated Lights-Out 2 IML Integrated Management Log IP Internet Protocol ISEE Instant Support Enterprise Edition KVM keyboard, video, and mouse LED light-emitting diode NBP Network Bootstrap Program NEMA National Electrical Manufacturers Association NFPA National Fire Protection Association NFS network file system NIC network interface controller ORCA Option ROM Configuration for Arrays Acronyms and abbreviations 86
OSEM Open Services Event Manager POST Power-On Self Test PSP ProLiant Support Pack PXE Preboot Execution Environment RAID redundant array of inexpensive (or independent) disks RBSU ROM-Based Setup Utility RDP Rapid Deployment Pack ROM read-only memory SAN storage area network SAS serial attached SCSI SATA serial ATA SFF small form-factor SFP small form-factor pluggable SIM Systems Insight Manager Acronyms and abbreviations 87
SNMP Simple Network Management Protocol TCP/IP Transmission Control Protocol/Internet Protocol TFTP Trivial File Transfer Protocol UID unit identification USB universal serial bus VCA Version Control Agent WEBES Web-Based Enterprise Service WfM Wired for Management Acronyms and abbreviations 88
Index A access panel 16, 17 ACU (Array Configuration Utility) air baffle 17 Array Configuration Utility (ACU) ASR (Automatic Server Recovery) authorized reseller 77 auto-configuration process 45 Automatic Server Recovery (ASR) Autorun menu 44 D 46 46 47 47 B batteries, replacing 68, 73 battery 10, 68, 73 battery-backed write cache enabler 31 bay numbering 12 BIOS Serial Console 46 BIOS upgrade 47 boot diskette 43 boot options 45 BSMI notice 72 buttons 6 C cables 12, 33, 55, 71 cabling 19 Care Pack 51 ca
hardware options 21 hardware options installation 21 health driver 47 help resources 77 HP Insight Diagnostics 49 HP ProLiant Essentials Foundation Pack 48 HP Systems Insight Manager, overview 48 HP technical support 77 I identification number 69 iLO (Integrated Lights-Out) 37, 42, 43, 47 iLO Advanced Functionality 37 iLO connector 13 IML (Integrated Management Log) 49 Important Safety Information document 52 Insight Diagnostics 49 installation, server options 21 installing operating system 40 Instant Supp
S utilities, deployment 41, 44 safety considerations 52 safety information 48 SAN configuration 43 scripted installation 41 serial number 46 series number 69 server blade bay numbering 12 server blade enclosure 12 server blade enclosure bay numbering 12 server blade installation 20 server blade removal 16 server fault indications flowchart 65 server features and options 21 service notifications 55 setting up a network 38 SmartStart autorun menu 44 SmartStart Scripting Toolkit 41 SmartStart, overview 44 so