reference guide hp StorageWorks SSL1016 tape autoloader Fourth Edition (June 2003) Part Number: 272363-004 This guide provides step-by-step instructions for installation, and is a reference for operation, troubleshooting, and upgrades.
© 2003 Hewlett-Packard Company. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright.
contents Contents About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Text Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 2 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 SCSI Bus Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 SCSI Cable and Terminator Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Transporting Tape Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storing Tape Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Write-Protect Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DLT IV Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents View Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Move Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Run Inventory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set to Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Declaration of Conformity for products marked with the FCC logo - United States only141 Canadian Notice (Avis Canadien) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Class A Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Class B Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 European Union Notice . . . . . . .
Contents 8 SSL1016 Tape Autoloader Reference Guide
about this guide About this Guide This reference guide provides information to help you: ■ Install and configure the autoloader About this Guide ■ Properly use and maintain tape cartridges ■ Operate the autoloader ■ Troubleshoot the autoloader ■ Upgrade or replace Customer Replaceable Units About this Guide topics include: ■ Conventions, page 10 ■ Rack Stability, page 12 ■ Getting Help, page 13 SSL1016 Tape Autoloader Reference Guide 9
About this Guide Conventions Conventions consist of the following: ■ Document Conventions ■ Text Symbols ■ Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases.
About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains. They have the following meanings.
About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week. Note: For continuous quality improvement, calls may be recorded or monitored. Outside North America, call technical support at the nearest location.
About this Guide 14 SSL1016 Tape Autoloader Reference Guide
1 Overview The HP StorageWorks SSL1016 Tape Autoloader provides a compact, high-capacity, low cost solution for simple, unattended data backup. The autoloader supports one DLT1, SDLT 320, or Ultrium 460 tape drive and two removable magazines. Each magazine can accommodate up to eight cartridges. Front View The mailslot, LCD, function keys, status LEDs, On/Off button, and left and right magazines are visible on the front panel of the autoloader.
Overview Mailslot The autoloader has a manual entry port, the mailslot, which allows you to load or unload a single cartridge. To maintain security, the mailslot can be password protected. Provided that the tape drive is empty, a cartridge can be inserted in the mailslot even if both magazines are completely filled. LCD The LCD allows you to use the scrolling menu to perform diagnostics and to enter commands.
Overview Status LEDs The status LEDs show autoloader and drive status information. The left, green LED shows ready status information, and the right, amber LED shows fault status information. On/Off Button The On/Off button is a soft key, which means that if the autoloader is moving any cartridges when you press the On/Off button, it finishes moving them before powering off.
Overview Rear View The fans and connection ports are visible on the back of the autoloader. 2 3 4 2 1 5 6 7 Figure 4: Autoloader rear view 1 AC power plug 5 Switches (factory use only) 2 Fan 6 SCSI connectors 3 Manual magazine eject slot 7 Manual magazine eject slot 4 Ethernet connector Cooling Fans The autoloader has a system cooling fan, plus a second fan to cool the power supply.
Overview Ethernet Connection The ethernet connection lets you connect the autoloader to a network, enabling remote administration. Via the network, the autoloader can access an SNMP server and a Simple Network Time Protocol (SNTP) time server. The ethernet connection supports File Transfer Protocol (ftp) and Hyper Text Transfer Protocol (http). You can download firmware updates using ftp and perform administrative tasks, including diagnostics, using http.
Overview Internal View Figure 5 shows the internal components of the autoloader. The picker sits behind the front panel and mailslot, and can accept and eject cartridges from the mailslot, magazines, and tape drive. The drive carrier assembly (DCA) contains the tape drive, internal power supply, controller board, and cooling fan; it can be removed and replaced as a single component.
Overview DCA The drive carrier assembly (DCA) is configured with one DLT1, SDLT 320, or Ultrium 460 tape drive, depending on the model. The DCA facilitates the easy removal of the drive. To change tape drives, you can replace the DCA without having to remove the top cover of the autoloader. Barcode Reader The barcode reader provides inventory feedback to the host application and/or LCD panel by reading the cartridge barcode labels.
Overview 22 SSL1016 Tape Autoloader Reference Guide
2 Installation and Configuration Preparation Make sure that the work area is free from conditions that could cause electrostatic discharge (ESD). See Appendix B, “Electrostatic Discharge,” for additional information. You will need a #2 Phillips screwdriver for rackmount installations.
Installation and Configuration The following cables are shipped with your autoloader: ■ 68-pin VHDCI connector to 68-pin VHDCI connector 3 foot (.092 meter) cable ■ 68-pin VHDCI connector to 68-pin VHDCI connector 6 foot (1.83 meter) cable ■ 68-pin VHDCI connector to 68-pin HD connector 6 foot (1.83 meter) cable SCSI Cable and Terminator Requirements If the autoloader is the last device on the SCSI bus you must attach a terminator to the SCSI connector on the back panel of the autoloader.
Installation and Configuration ■ Documentation CD (documents in PDF format) Installation Location Caution: To prevent damage to the tapes and the tape drives, position the autoloader so that no cooling vents are located directly in front of the unit; this helps minimize the amount of foreign debris entering the tape path.
Installation and Configuration Required Tools and Hardware for Rackmount Installation You need a Phillips screwdriver to install your autoloader into a rack. Make sure you have all the necessary parts you need before you begin installation.
Installation and Configuration To rackmount the autoloader: 1. Use the template that shipped with the library to mark the location of the clip nuts and mounting hardware on the mounting rails of the rack. Figure 6: Measuring with the rack template 2. Install two clip nuts into each front rail of the rack in the hole locations marked using the template. 3. Install two clip nuts into each back rail of the rack in the hole locations marked using the template. 4.
Installation and Configuration c. Hook the curved tabs around the rear rail of the rack 1. d. Align the rail so that the holes are over the previously installed clip nuts 2. e. Secure with two screws 3. f. Attach the other optional mounting bracket using steps b through e.
Installation and Configuration 5. Attach the two support brackets to the rear of autoloader, tightening screws until snug. Caution: Be sure the support brackets are aligned straight with the sides of the autoloader for proper installation into the U-channel brackets.
Installation and Configuration 6. Attach the two rackmount handles 1 to the front of the autoloader, tightening the studs 2 until snug.
Installation and Configuration 7. Attach one U-channel bracket to each rear rail of the rack, loosely installing the screws through the clipnuts. (Attach the side of the bracket with only two holes.) Do not tighten the screws. Figure 10: Attaching the U-channel brackets to the rack 8. Position the autoloader in the rack so that each support bracket rests on a U-channel bracket. Each support bracket slides along the lip of the U-channel bracket.
Installation and Configuration 9. Slide the autoloader in place 1 so that: a. The mounting studs on the front ears of the autoloader slide into the holes between the clip nuts. b. The front ears of the autoloader align with the front clips. c. The rear support brackets engage the locking tab on the rear U-channel brackets. 1 2 2 Figure 12: Attaching the autoloader to the front of the rack 10. Loosely install a screw in each front clip nut to attach the ears 2. 11. Verify that the autoloader is level.
Installation and Configuration Figure 13: Rear U-channel bracket screws 15. If additional products are going to be installed below the autoloader, remove the optional installation brackets: a. Remove the two screws securing each bracket to the front of the rack. b. Pull the bracket forward and down, then push back to release the rear tabs. c. Remove the rail from the rack.
Installation and Configuration Removing the Autoloader From the Rack When removing the autoloader from the rack: ■ Always use at least two people. ■ Install the optional installation brackets if there is no device installed below the autoloader. ■ Before powering off the autoloader, remove the magazines. Standalone Installation Use these instructions if you will not be installing your autoloader into a rack. Preparation To prepare your autoloader for standalone installation: 1.
Installation and Configuration 2. Install the front standalone bracket cover: a. Place the cover over the autoloader bracket. b. Place the washers over the bracket holes and secure with a screw. c. Repeat for the other side. Figure 15: Installing the front standalone bracket covers Clearance Place the autoloader on a desk, table, or other stable, horizontal surface. Make sure the fan at the rear of the autoloader is not obstructed. Allow about 6 inches (about 15 cm) from wall or solid object at the rear.
Installation and Configuration SCSI Connection The SCSI connection lets the host computer communicate with the autoloader. Note: If you do not already have a compatible and available SCSI HBA installed in the host computer, install one before proceeding. Caution: When installing cables, be careful not to damage the SCSI pins on the connectors. Damaged pins will cause the connection to fail. To make the SCSI connection: 1.
Installation and Configuration Figure 16: Attaching the cables Note: The connector on the end of the cable is offset. Make sure that you install it with the correct orientation so that you can fit a terminator or another cable in the other port. 5. If the autoloader will be the last device on the SCSI bus, install the supplied SCSI terminator to the remaining port that is on the DCA and then tighten the screws. 6.
Installation and Configuration Daisy Chaining The autoloader does not support daisy chaining with other products. You can daisy chain one additional autoloader using the 68-pin VHDCI connector to 68-pin VHDCI connector 3 foot (.092 meter) cable. You must then install a terminator on the second autoloader. Ethernet Connection Attach one end of the RJ-45 cable to the autoloader. Attach the other end to a 10/100 hub or switch.
Installation and Configuration Figure 17: Connecting the power cord Note: Do not power on the host before powering on the autoloader. To power on the autoloader: 1. Push the power switch that is on the back of the autoloader to the on position (the | is pressed). Wait while the autoloader performs its power-on sequence. During this time, the following activities occur: ■ The cooling fans begin to operate. ■ The LCD illuminates and displays power-on messages.
Installation and Configuration Verification When you first power on the autoloader, it automatically runs a Power On Self Test (POST). During the POST, the right (amber) LED flashes rapidly. After the POST, the left (green) LED illuminates steadily, and after approximately three minutes the LCD displays the HP logo and drive type. Do one of the following: ■ If the autoloader powers on successfully, continue configuring the autoloader. See “Configuration.
Installation and Configuration The Configuration submenu has the following options: Configuration SCSI ID Ethernet Set IP Dynamic (DHCP) Static Set Subnet Mask Set Gateway Set SNMP Server Set Time Server Time Set Timezone Set Date/Time Change Mode Random Mixed Sequential Seq Cycle Mode Cleaning Tape Auto Clean Tape Location Compression I/E Slot Security Security Set Password Operator Administrator System Update Figure 18: Configuration submenu Note: The autoloader ships with English firmware installed.
Installation and Configuration To configure the autoloader, you must set the following: ■ SCSI ID ■ Ethernet IP address (if you are not using DHCP) ■ SNMP server IP address (for SNMP alerts) ■ Time server IP address (or the timezone, date, and time, if configuring manually) Note: The DLT1 and SDLT autoloaders do not have a battery so if time is manually set, it is lost and needs to be reset whenever the autoloader is power cycled.
Installation and Configuration To set the SCSI ID: 1. On the main menu, scroll to Configuration. Status Commands Configuration Diagnostics Figure 19: Main menu 2. Press Enter. 3. On the Configuration submenu, scroll to SCSI ID. SCSI ID Ethernet Time Change Mode Figure 20: Select SCSI ID 4. Press Enter. 5. Scroll to the number you want to set as the autoloader SCSI ID. to change Enter to continue SCSI ID: 05 Figure 21: Set SCSI ID 6. Press Enter. 7. Reboot for the new SCSI ID to take affect. a.
Installation and Configuration Control Mode You can set the autoloader to either Random, Mixed, Sequential, or Seq Cycle Mode. The default control mode is Random. Note: If the I/E slot is enabled, the autoloader cannot be used in Mixed or Sequential Mode. The Sequential mode supports certain backup applications that do not manage media.
Installation and Configuration To set the control mode: 1. On the main menu, scroll to Configuration. Status Commands Configuration Diagnostics Figure 22: Main menu 2. Press Enter. 3. On the Configuration submenu, scroll to Change Mode. SCSI ID Ethernet Time Change Mode Cleaning Tape Figure 23: Select Change Mode 4. Press Enter. The mode options appear. A checkmark appears after the enabled mode. 3 Random Mixed Sequential Seq Cycle Mode Figure 24: Mode Options 5.
Installation and Configuration Note: When you enable the Sequential mode, LUN 1 no longer appears on the SCSI bus. Sequential Mode Operation If you enable the Sequential control mode you must use the Sequential Ops submenu under the Commands menu to operate the autoloader after it has been rebooted. ■ Start allows you to load the first cartridge. ■ Resume allows you to continue if the cycle was stopped. ■ Stop stops the cycle. To start Sequential Mode operation: 1.
Installation and Configuration 5. On the Sequential Ops submenu, scroll to Resume. 6. Press Enter. Ethernet Ethernet is the method the autoloader uses to access a network. With an Ethernet connection, you can remotely access the autoloader over the network to which it is connected.
Installation and Configuration To set a dynamic IP address: 1. On the main menu, scroll to Configuration. Status Commands Configuration Diagnostics Figure 25: Main menu 2. Press Enter. 3. On the Configuration submenu, scroll to Ethernet. SCSI ID Ethernet Time Change Mode Figure 26: Select Ethernet 4. Press Enter. 5. On the Ethernet submenu, scroll to Set IP. Set IP Set Subnet Mask Set Gateway Set SNMP Server Figure 27: Set IP 6. Press Enter. 7. Scroll to Dynamic (DHCP). Dynamic 3 Static IP 016.117.
Installation and Configuration 9. Reboot to change the IP address. a. Press and hold the power button on the front panel until Power Off appears on the LCD. b. Press the power button again to power on the autoloader. The IP address is changed. To set a permanent IP address: 1. On the main menu, scroll to Configuration. (See Figure 25.) 2. Press Enter. 3. On the Configuration submenu, scroll to Ethernet. (See Figure 26.) 4. Press Enter. 5. On the Ethernet submenu, scroll to Set IP. (See Figure 27.) 6.
Installation and Configuration 3. On the Configuration submenu, scroll to Ethernet. (See Figure 26.) 4. Press Enter. 5. On the Ethernet submenu, scroll to Set Subnet Mask. (See Figure 27.) 6. Press Enter. 7. At each position of the mask address, scroll to the correct number and press Enter to advance your cursor. Subnet Mask: 255.255.195.000 Figure 29: Setting the Subnet Mask Note: Use the Escape key to backspace to a previous text box, if necessary.
Installation and Configuration 7. At each position of the gateway address, scroll to the correct number and press Enter to advance your cursor. Default Gateway: 016.117.065.001 Figure 30: Setting the gateway address Note: Use Escape to backspace to a previous text box, if necessary. When you have set the gateway address, the autoloader displays Enter to save. 8. Press Enter. GW changed appears on the display. You do not need to reboot the autoloader. 9. Press Escape or Enter to return to the menu.
Installation and Configuration 7. At each position of the server address, scroll to the correct number and press Enter to advance your cursor. SNMP Server: 255.255.255.255 Figure 31: Setting the SNMP server address Note: Use the Escape key to backspace to a previous text box, if necessary. When you have set the server address, the autoloader displays Enter to save. 8. Press Enter. SNMP Server changed to appears on the LCD. You do not need to reboot the autoloader. 9.
Installation and Configuration 7. At each position of the server address, scroll to the correct number and press Enter to advance your cursor. Time Server: 192.005.044.041 Figure 32: Setting the time server address Note: Use the Escape key to backspace to a previous text box, if necessary. When you have set the server address, the autoloader displays Enter to save. 8. Press Enter. Time Server changed to appears on the panel display. You do not need to reboot the autoloader. 9.
Installation and Configuration 2. Press Enter. 3. On the Configuration submenu, scroll to Time. SCSI ID Ethernet Time Change Mode Figure 34: Select Time 4. Press Enter. 5. On the Time submenu, scroll to Set Timezone. Set Timezone Set Date/Time Figure 35: Select Set Timezone 6. Press Enter. The timezone screen appears. Timezone: set hrs GMT +0:00 Figure 36: Timezone screen 7. Scroll to set the number of hours difference between your local time and Greenwich Mean Time (GMT). 8. Press Enter.
Installation and Configuration A new timezone screen appears. Timezone: set mins GMT +0:00 Figure 37: New timezone screen 9. Scroll to set the number of minutes’ difference between your local time and Greenwich Mean Time (GMT). 10. Press Enter. The new timezone is set. To set the date and time: 1. On the main menu, scroll to Configuration. (See Figure 33.) 2. Press Enter. 3. On the Configuration submenu, scroll to Time. (See Figure 34.) 4. Press Enter. 5. On the Time submenu, scroll to Set Date/Time.
Installation and Configuration 7. The first four digits represent the current year. For each digit, scroll to the correct number and press Enter to advance your cursor. Note: Use the Escape key to backspace to a previous text box, if necessary. 8. The next two digits represent the current month. For each digit, scroll to the correct number and press Enter to advance your cursor. 9. The next two digits represent the current day.
Installation and Configuration 2. Press Enter. 3. On the Configuration submenu, scroll to Security. Cleaning Tape Compression I/E Slot Security Figure 41: Select Security 4. Press Enter. 5. On the Security submenu, scroll to Security. If a checkmark appears after the word, the security option is on. If no checkmark appears, the security option is off. 3 Security Set Password Figure 42: Security options 6. To change the setting, press Enter. This toggles the security option.
Installation and Configuration 5. On the Security submenu, scroll to Set Password. 3 Security Set Password Figure 43: Select Set Password 6. Press Enter. 7. To set a password at the operator level, scroll to Operator. To set a password at the administrator level, scroll to Administrator. Operator Administrator Figure 44: Select password level 8. Press Enter. The Set Password screen appears. Login as OP Enter New Password ❋❋❋❋❋❋ Figure 45: Set Password screen 9. Press Enter again.
Installation and Configuration Note: Use the Escape key to backspace to a previous text box, if necessary. When you have entered six numbers, the autoloader displays Submit Password below the asterisks. 13. Press Enter to submit the password. Password Successfully Changed appears on the LCD. 14. Press Enter. The Operator and Administrator options reappear. You can either enter another password, or press Escape or Enter to return to the main menu.
Installation and Configuration 60 SSL1016 Tape Autoloader Reference Guide
3 Tape Cartridge Usage This chapter describes the magnetic tapes and how to handle them properly. Tape Cartridges Defined The following tables list the types of media supported in each tape autoloader.
Tape Cartridge Usage Table 4: SDLT 320 Supported Media .
Tape Cartridge Usage ■ 200 GB (Ultrium 1) data cartridges are blue and provide storage capacity of up to 100 GB (native)/200 GB (compressed). Tape Cartridge Maintenance To greatly reduce the chance of problems with your tape cartridges or damage to your tape drive, use the following guidelines. Inspecting Tape Cartridges Inspect your tapes to identify any potential tape cartridge problems and prevent accidental loss of data or damage to your cartridges.
Tape Cartridge Usage 4. If you hear anything on DLT or SDLT cartridges, do not use the cartridge. a. If it doesn't rattle, check the tape leader inside the cartridge. To do this, open the door on the rear of the cartridge by releasing the door lock.
Tape Cartridge Usage b. For SDLT cartridges: The loop should stick up about an eighth of an inch when viewed from the edge; the loop must be a closed loop. If the loop is torn, bent, pulled in, or not sticking up about an eighth of an inch, do not use the tape cartridge.
Tape Cartridge Usage c. For DLTtapes: hold the tape cartridge so that the end that is inserted into the tape drive is facing you. On the left side of the tape cartridge you should see a small plastic tab. This is the left reel lock and can break if the cartridge is dropped. If you cannot see the tab, do not use the cartridge. d.
Tape Cartridge Usage Protecting Tape Cartridges To extend the life of your tape cartridges: ■ Remove dust on the outside of tape cartridges with a damp cloth. ■ Do not use adhesive labels or POST-IT notes on the top, side, or bottom of your tape cartridge. Use only the label provided with each cartridge and slide it in the label slot on the cartridge. ■ Do not use graphite pencils, water-soluble felt pens, or other debris-producing writing instruments on labels. ■ Replace — never erase — a label.
Tape Cartridge Usage Transporting Tape Cartridges To safely transport tape cartridges: ■ Always keep each tape cartridge in its protective plastic case when it is not in the tape drive. ■ When carrying tape cartridges in their cases, always orient the cases so that the grooves in the cases interlock. This prevents the cases from slipping apart and falling. ■ Do not carry cartridges loosely in a box or in any other container.
Tape Cartridge Usage Using the Write-Protect Switch All tape cartridges have a write-protect switch to prevent accidental erasure of data. When you enable write-protection, existing data on the tape cannot be overwritten, nor can additional data be appended to the tape. When you disable write-protection, existing data on the tape can be overwritten, and additional data can be appended.
Tape Cartridge Usage Table 6: Write-Protect Switch Positions Write-Protect Switch Position Write-Protected (with the hub facing down and the write-protect switch facing you as shown in Figure 49, slide the switch to the left.) Write-Enabled (with the hub facing down and the write-protect switch facing you as shown in Figure 49, slide the switch to the right.) 70 Orange Indicator Visible Not visible Result ■ Data cannot be written to the tape. ■ Existing data on the tape cannot be overwritten.
Tape Cartridge Usage SDLT 320 Cartridge Figure 50 illustrates using the write-protect switch. By moving the switch to the left 1, the cartridge is write-protected, and by moving the switch to the right 2, the cartridge is write-enabled.
Tape Cartridge Usage Ultrium Data Cartridge 1 shows the location of the right protect switch. By moving the switch on the bottom of the cartridge to the right, the cartridge is write-protected, and by moving the switch to the left, the cartridge is write-enabled.
Autoloader Operation 4 You can operate the autoloader by any of the following methods: ■ Autoloader front panel — Operate manually to insert and eject tapes and to unload magazines. ■ Ethernet Web Administration — The Ethernet connection lets you perform administrative functions remotely using Web Administration. You can also move tapes within the autoloader through the Ethernet connection. ■ Host backup software — The SCSI bus connects the autoloader to the host server and the backup software.
Autoloader Operation LEDs The LEDs display autoloader and drive status information. When the autoloader is powered on, the left, green LED gives ready status information, and the right, amber LED gives fault status information. Table 7: Indicator Activity Indicator State Operating Condition Left (green) On Slow Flash Fast Flash Autoloader and tape drive are idle. Tape drive only is active. Autoloader only is active or autoloader and tape drive are active.
Autoloader Operation Status Commands Configuration Diagnostic Tests Autoloader Eject SCSI ID Error Logs Ethernet Halt Test Status Tape to Mail Slot Set IP Self Test Version By Barcode Element Status By Location Dynamic (DHCP) Health Check From Drive Static IP Picker Test Drive Status Right Magazine Set Subnet Mask Magazine Test Version Left Magazine Set Gateway Inventory Test Set SNMP Server Drive Read Set Time Server Drive Write Ethernet Enter (Mail Slot) To Drive To Lo
Autoloader Operation The administrator password accesses all the available functionality. The operator password accesses all the functionality in the Commands and Status submenus. Front Panel Functionality For most functions, you can use either the front panel or the Web Administration tool through the Ethernet connection. Setting Passwords Many functions on the autoloader may be password-protected to ensure data integrity.
Autoloader Operation Using Data Cartridges Typically, when you first install your autoloader, you insert your cartridges into the magazines and then insert the magazines into the autoloader. However, you can insert and eject cartridges individually using the mailslot, or you can eject a magazine, manually insert and remove cartridges, then insert the magazine back into the autoloader. The autoloader automatically detects the presence of a cartridge in the mailslot and in a magazine slot.
Autoloader Operation After Load cartridge appears on the LCD, a countdown appears. You have 20 seconds to load a cartridge through the mailslot before it relocks. The autoloader automatically loads the cartridge into the tape drive. Note: Only insert the cartridge until you meet resistance. Figure 53: Inserting a cartridge into the mailslot To insert a cartridge to a magazine slot: 1. On the main menu, scroll to Commands. 2. Press Enter. 3. On the Commands submenu, scroll to Enter. 4. Press Enter. 5.
Autoloader Operation After Load cartridge appears on the LCD, a countdown appears. You have 20 seconds to load a cartridge through the mailslot before it relocks. The autoloader automatically loads the cartridge into the selected slot. Moving a Single Cartridge To move a single cartridge from one location to another inside the autoloader: 1. On the main menu, scroll to Commands. 2. Press Enter. 3. On the Commands submenu, scroll to Move. 4. Press Enter. The Move screen appears. 5.
Autoloader Operation Ejecting a Single Cartridge You can remove a single cartridge from the autoloader by specifying the desired cartridge by barcode or location, or by choosing the cartridge currently in the tape drive. To eject a cartridge by barcode: 1. On the main menu, scroll to Commands. 2. Press Enter. 3. On the Commands submenu, scroll to Eject. 4. Press Enter. 5. On the Eject submenu, scroll to Cartridge. 6. Press Enter. 7. Scroll to By Barcode. A barcode label appears. 8.
Autoloader Operation An hourglass appears on the LCD as the cartridge you want is ejected from the mailslot.Wait until the hourglass disappears from the LCD before pulling out the cartridge. To eject a cartridge from the tape drive: 1. On the main menu, scroll to Commands. 2. Press Enter. 3. On the Commands submenu, scroll to Eject. 4. Press Enter. 5. On the Eject submenu, scroll to Cartridge. 6. Press Enter. 7. Scroll to From Drive. 8. Press Enter.
Autoloader Operation You will hear a distinctive popping sound as the appropriate magazine is ejected from the autoloader. Left magazine has been ejected or Right magazine has been ejected appears on the LCD. Caution: To prevent damage to the autoloader or the magazine, use both hands when removing the magazine from the autoloader, supporting the entire length of the magazine. 7. Grasp the magazine by the handle with one hand and slide it out, supporting it underneath with the other hand.
Autoloader Operation Installing a Magazine To install a magazine: Note: Be sure you are using the proper magazine for your autoloader. DLT/SDLT magazines are not compatible with the SSL1016 Ultrium 460 Autoloader. Ultrium magazines are not compatible with the SSL1016 DLT1 Autoloader or the SSL10106 SDLT 320 Autoloader. 1. Grasp the magazine by the handle with one hand and support it underneath with the other hand. 2. Slide the magazine into the magazine bay.
Autoloader Operation Inserting and Removing Cartridges The magazine must be fully removed to insert and remove cartridges. There are two gears located on both ends of the magazine. Move the slots within the magazine by using these two gears. Use the two openings along the top of the magazine and the four openings along the bottom of the magazine to insert and remove cartridges from the eight slots within each magazine. To insert a cartridge into the magazine: 1.
Autoloader Operation Manually Removing a Magazine To remove a magazine manually: 1. Power off the autoloader. 2. Place the autoloader on a flat, stable surface. 3. Locate the small rectangular opening on the back of the autoloader behind the magazine that you want to remove.
Autoloader Operation 4. Carefully insert the end of a small, sturdy tool, such as a jeweler’s screwdriver, about one inch into the opening. On a right magazine, keep the tool as far to the left as you can. On a left magazine, keep the tool as far to the right as you can. 5. On a right magazine, slide the tool to the right. On a left magazine, slide the tool to the left. You will feel resistance as the tool presses against the latch. Press hard enough to release the latch.
Autoloader Operation Changing the Orientation Any magazine can be configured to fit in the right or left magazine bay. To change the orientation of a magazine: 1. Remove the two screws that attach the handle to the front of the magazine. Figure 59: Removing the screws 2. Unsnap the handle carefully, ensuring you do not break the hinge. 3. Rotate the handle 180 degrees so that what was the top of the handle is now the bottom. 4.
Autoloader Operation 2 1 Figure 60: Removing the handle 5. Snap the handle back on the end of the magazine. 6. Install the two screws to attach the handle securely to the magazine.
Autoloader Operation Autoloader Status The autoloader status provides information about: ■ Whether a magazine is installed or not ■ SCSI connection activity ■ Ethernet connection activity To view the autoloader status: 1. On the main menu, scroll to Status. Status Commands Configuration Diagnostics Figure 61: Main menu 2. Press Enter. 3. On the Status submenu, scroll to autoloader Info. Autoloader Info Drive Info Ethernet Info Figure 62: Select Autoloader Info 4. Press Enter. 5.
Autoloader Operation A list of messages similar to the following screen appears. Magazines: L ❋ R ❋ Loader: ONLINE Drive: ONLINE Mode: Mixed Barcode Reader: ❋ Figure 64: Autoloader status message Table 8: Autoloader Status Messages Magazine L=❋ The left magazine is present. R=❋ The right magazine is present. L= (no ❋) The left magazine is not present. R= (no ❋) The right magazine is not present. Loader ONLINE The autoloader SCSI connection is active.
Autoloader Operation View Firmware Version To view the firmware version: 1. On the main menu, scroll to Status. (See Figure 61.) 2. Press Enter. 3. On the Status submenu, scroll to Autoloader Info. (See Figure 62.) 4. Press Enter. 5. On the autoloader Info submenu, scroll to Version. (See Figure 63.) 6. Press Enter. A list of messages similar to the following screen appears. Firmware: V7.
Autoloader Operation View Element Status The element status reports the status of the magazine slots. The status indicates whether a slot contains a cartridge, and which slot is allocated as the cleaning cartridge’s slot. To view an element’s status: 1. On the main menu, scroll to Status. (See Figure 61.) 2. Press Enter. 3. On the Status submenu, scroll to Autoloader Info. (See Figure 62.) 4. Press Enter. 5. On the autoloader Info submenu, scroll to Element Status. (See Figure 63.
Autoloader Operation The Element Status screen appears, displaying the barcode label for that cartridge (if an inventory has previously been run). A move command also appears on the screen. Label: DRC101 Move Slot 2 To: Slot 9 Esc to Exit Figure 68: Element status screen a. If you want to move the cartridge scroll until the location you want to move to appears under TO:, then press Enter. b. If you do not want to move the cartridge, press Escape. View Tape Drive Status To view the tape drive status: 1.
Autoloader Operation Table 10: Tape Drive Status Messages SCSI ID The number indicates the autoloader SCSI ID number. Loader LUN The number indicates the Logical Unit Number of the autoloader. Compression Indicates whether the tape drive compression is enabled or disabled. Drive Cart Indicates whether a cartridge is present in the drive. View Tape Drive Version To view the tape drive version: 1. On the main menu, scroll to Status. (See Figure 61.) 2. Press Enter. 3.
Autoloader Operation View Ethernet Information To view Ethernet information: 1. On the main menu, scroll to Status. (See Figure 61.) 2. Press Enter. 3. On the Status submenu, scroll to Ethernet Info. (See Figure 62.) 4. Press Enter. A list of messages similar to the following screen appears. MAC address: 00-e0-9e-03-0e-39 IP Address 16.116.76.
Autoloader Operation 3. On the Commands submenu, scroll to Inventory. 4. Press Enter. The autoloader scans the barcodes on all the cartridges present. Note: If no barcode label is present the autoloader checks for the presence or absence of cartridges in all locations. Set Data Compression You can set the autoloader to write data to the tape in its native (uncompressed) format or to compress it.
Autoloader Operation 4. Press Enter. If a check appears next to Compression, the compression option is enabled. If no checkmark appears, the compression option is disabled. a. To leave the compression option unchanged, press Escape. b. To change the compression option, press Enter. Update Firmware Autoloader firmware can be updated by using Library & Tape Tools (L&TT). Additional details can be obtained at: http://www.hp.
Autoloader Operation 3. On the Configuration submenu, scroll to I/E Slot. Cleaning Tape Compression I/E Slot Security Figure 75: Configure Import/Export Slot 4. Press Enter. If a check appears next to Import/Export Slot, the I/E slot is enabled. If no checkmark appears, the I/E slot is disabled. a. To leave the I/E slot unchanged, press Escape. b. To change the I/E slot, press Enter. Any change requires a power cycle of the autoloader and reconfiguration of the ISV software.
Autoloader Operation Web Administration Many of the same operations performed from the front panel can also be performed remotely using Web Administration. The following browsers are recommended for use with Web Administration: ■ Windows® — Internet Explorer 5.0, 5.5, and 6.x — Netscape 4.x and 6.x ■ Linux, Unix®, and Sun Solaris™ 8 — Netscape 4.x and 6.x After establishing a connection to the autoloader, open the HTML browser and enter the IP address of the autoloader.
Autoloader Operation Default Password The default user ID is guest. The default password is guest. See “Set Security Option” in this chapter for information on changing the user ID and password. Status information appears on the right side of the home page and every page of Web Administration. The menu headings also appear at the top of every page. To access the functionality under the menu heading, click the menu heading.
Autoloader Operation View Status Information To view status information from Web Administration, you only have to open it. You do not need to execute any command to see it because the status information appears on the right side of every page. This information is updated automatically every 10 seconds, so the status you see is real-time information. Move Tapes To move a tape: 1. On any Web Administration page, click Commands. 2.
Autoloader Operation Figure 78: Moving tapes using Web Administration 102 SSL1016 Tape Autoloader Reference Guide
Autoloader Operation Run Inventory The autoloader automatically runs an inventory when you power it back on or insert a magazine. If you need to run an inventory in addition to this, you can use Web Administration to do it remotely. To run an inventory: 1. On any Web Administration page, click Commands. 2. On the Commands page, click Inventory.
Autoloader Operation Run Diagnostic Tests If the status information indicates an error, view the event log. To view the event log: 1. On any Web Administration page, click Diagnostics. Figure 79: Diagnostic page 2. Click View Log. Note: See Chapter 6, “Troubleshooting,” for a list of error messages. When an error message appears in the status information, you may need to run a diagnostic test. To run a diagnostic test: 1. On any Web Administration page, click Diagnostics. 2.
Autoloader Operation 4. While the test is running, you can view the status of the test by clicking View Status. To refresh the status information, click the Back button on your browser, and then click the View Status button again. 5. To save the report, click File, Save As, then navigate to the directory where you want it saved. Set the System Time If your autoloader is not connected to a time server, you can set the time manually with Web Administration.
Autoloader Operation Figure 80: Setting system time To set the date and time: 1. On any Web Administration page, click Configurations. 2. From the month drop-down list, select the current month. 3. From the day drop-down list, select the current day. 4. From the year drop-down list, select the current year. 5. In the hour text box, type the current hour, in 24-hour format. 6. In the minute text box, type the current minute. 7. Click submit.
Autoloader Operation Change the SCSI ID If you need to change the autoloader’s SCSI ID, you can do so from the Web Administration tool. To change the SCSI ID: 1. On any Web Administration page, click Configurations. 2. From the drop-down list under SCSI ID, click the number to which you want to set the ID. Figure 81: Setting the SCSI ID 3. Click submit. You must reboot the autoloader before the new SCSI ID takes effect.
Autoloader Operation Set the Control Mode To set the control mode: 1. On any Web Administration page, click Configurations. Under Mode, the current mode is selected. Figure 82: Setting the Control Mode 2. To change the mode, click a different option. 3. Click submit. You must reboot the autoloader before the new mode takes effect.
Autoloader Operation Set the Compression Note: Typically you will want to leave this option enabled unless you are backing up data that is already compressed. Attempting to compress compressed data can reduce performance and increase data size. To set the compression: 1. On any Web Administration page, click Configurations. 2. If a checkmark appears in the box next to Compression, compression is enabled. To disable compression, click the box to remove the checkmark. 3.
Autoloader Operation Set the Cleaning Mode To enable the Auto Clean function, you must have a slot designated for the cleaning tape cartridge. If you or another user have already designated a slot, that slot’s number appears next to Cleaning Cartridge Location. If a slot has not been designated, the box is empty. Note: Auto Clean is not supported on Windows 2000 removable storage. To set the cleaning tape slot: 1. On any Web Administration page, click Configurations. 2.
Autoloader Operation To set Auto Clean: 1. On any Web Administration page, click Configurations. 2. If a checkmark appears in the box next to Enable Auto Clean, the option is enabled. To disable Auto Clean, click the box to remove the checkmark. If no checkmark appears in the box next to Enable Auto Clean, the option is disabled. To enable Auto Clean, click the box to enter a checkmark. 3. Click submit. Note: A cleaning tape should be present in the cleaning tape slot to configure Auto Clean.
Autoloader Operation Set the Import/Export Slot To set the I/E slot: 1. On any Web Administration page, click Configurations. 2. If a checkmark appears in the box next to I/E Slot, the I/E slot is enabled. 3. If no checkmark appears in the box next to I/E Slot, the I/E slot is disabled. 4. Click submit. Figure 85: Import/Export Slot Any change requires a power cycle of the autoloader and reconfiguration of the ISV software.
Autoloader Operation Set Ethernet Configurations When you originally installed the autoloader, you set the Ethernet connections through the front panel. However, you can change them through the Web Administration tool. To change the Ethernet configurations: 1. On any Web Administration page, click Configurations. 2. On the secondary menu, click Networking. The current settings appear on the screen. Figure 86: Networking options 3.
Autoloader Operation 5. To set the IP address from a permanent address to a dynamic address, click the box next to DHCP, and delete the IP address from the IP address fields. 6. To change the IP address of the subnet mask, gateway, SNMP server, or the time server: a. Click the box to left of the address you want to change to enter a checkmark. b. Type in the new address, using your Tab key to move from box to box. 7. Click submit.
Autoloader Operation Set Security Option When you enable the security option, users must enter a password to access the autoloader’s functionality. A password allows either administrator-level access or operator-level access. (For more information on levels of password-protection, see “Security.”) To set the security option: 1. On any Web Administration page, click Configurations. 2. On the secondary menu, click Security. Figure 87: Security option 3.
Autoloader Operation Set Passwords When you enter your password on the autoloader front panel, there is no associated username. However, when you click any menu heading on the Web Administration’s home page, Web Administration prompts you for a username and password. In Web Administration, you can set up to four usernames and IDs, which can include both alpha and numeric characters. Usernames and IDs must be between four and seven characters long. To set a password: 1.
Autoloader Operation Update the Firmware To update the firmware: 1. On any Web Administration page, click Updates. Figure 88: Get system updates 2. Click Browse. 3. Navigate to the location of the firmware update. 4. Click Submit. The autoloader automatically uploads the new code and updates the firmware. Note: A message displays on the LCD to indicate that the update is complete. Do not power cycle the autoloader until this message displays.
Autoloader Operation 118 SSL1016 Tape Autoloader Reference Guide
Tape Drive Cleaning 5 Your tape drive read/write head should be cleaned periodically. When cleaning is needed, the drive automatically requests the backup software to perform a cleaning operation. However, you can also initiate cleaning from the front panel as needed. Use a cleaning tape to clean your tape drive. ■ The DLT1 tape cleaning tape looks just like a DLTtape IV cartridge, except that its shell is beige and has a stop next to the door hinge to prevent insertion in a non-compatible drive.
Tape Drive Cleaning 9. Press Enter. The selected slot has a ! next to the slot number. 10. To deconfigure the slot, press Enter again. The selected slot no longer has a ! next to the slot number. Inserting the Cleaning Tape There are two methods for inserting the cleaning tape: ■ Load the cleaning tape directly into an ejected magazine and then reload the magazine. ■ Insert the cleaning tape through the mailslot. To insert the cleaning tape through the mailslot: 1. On the main menu, scroll to Command.
Tape Drive Cleaning ■ If the Auto Clean function is enabled, the autoloader can move the cleaning tape from the magazine slot to the tape drive and, after the cleaning cycle, return it to its slot. ■ If backup software cleaning function is enabled, the software can move the cleaning tape from the magazine slot to the tape drive and, after the cleaning cycle, return it to its slot (for more information, see your backup software’s documentation). To store the cleaning tape: 1.
Tape Drive Cleaning 7. Press Enter to unload the cleaning tape from the drive. The autoloader moves the tape to its new location. Ejecting the Cleaning Tape You need to eject the cleaning tape from the autoloader under the following conditions: ■ If you do not want to store the cleaning tape in a magazine slot after manually cleaning the tape drive. ■ If the cleaning tape has expired. A cleaning tape cartridge can be used for 20 cleanings. To eject a cleaning tape: 1.
Tape Drive Cleaning Caution: Because the cleaning cartridge is abrasive, you should not use it unless the cleaning message appears. To clean the tape drive manually: 1. On the main menu, scroll to Command. 2. Press Enter. 3. On the Command submenu, scroll to Cleaning Tape. 4. Press Enter. 5. Log in as Operator. 6. On the Cleaning Tape submenu, scroll to Load to Drive. 7. Press Enter. The autoloader moves the cleaning tape from its slot to the tape drive and then cleans the drive with it.
Tape Drive Cleaning Auto Clean Note: Auto Clean is not supported on Windows 2000 removable storage. The Auto Clean function permits the autoloader to perform the cleaning process automatically without interrupting normal operation. The Auto Clean feature is turned off by default. With Auto Clean enabled, the autoloader monitors the cleaning requirements of the tape drive.
Tape Drive Cleaning 6. On the Cleaning Tape submenu, scroll to Auto Clean On/Off. If Auto Clean is enabled, the menu item appears as Auto Clean On. If Auto Clean is disabled, it appears as Auto Clean Off. 7. To change the setting, press the up or down scroll key once. 8. Press Enter. Software Set the cleaning option in your software application (if available) so that the software monitors drive cleaning.
Tape Drive Cleaning 126 SSL1016 Tape Autoloader Reference Guide
6 Troubleshooting Before Contacting Technical Support Before you contact technical support, use the information in this chapter to try and resolve the problem. Problems with the autoloader can occur in the following forms: ■ Operational Problems ■ Error Messages Operational Problems Operational problems can range from compatibility issues with the operating system to failure of the front panel. Table 13 describes the probable cause and suggested action for each operational problem you may encounter.
Troubleshooting Table 13: Suggested Actions for Operational Problems Problem Real Time Clock keeps getting reset/cleared. 128 Probable Cause Suggested Action Backup server isn't capable of sending data to the drive fast enough. For the SDLT and Ultrium drives, the backup server needs to have lots of memory, processing power, a dedicated SCSI bus and a fast file system. Network issues. Most networks aren't capable of sending data fast enough to the SDLT and Ultrium drives.
Troubleshooting Table 13: Suggested Actions for Operational Problems Problem Autoloader does not power up. Probable Cause Suggested Action The power cord or source is malfunctioning or the autoloader is incorrectly configured. Check all outlets and power cords for proper connection. The power switch on the back of the autoloader is set to 0. Flip the power switch on the back of the autoloader back to the | position and, if necessary, press the power button on the front of the autoloader.
Troubleshooting Understanding Error Messages When a failure first occurs, a two-digit error message appears on the front panel of the autoloader. See Table 14 for the error description and suggested repair. When viewing the error log from the front panel, the text that appears is similar to the following: Task: Picker Error: 02b9202f Contxt: 03ac/00400100 POC: 00022 POH: 00000:07:41: #14 Find the eight characters following “Error:” in the second line of the block of text.
Troubleshooting . Table 14: Error Messages Error Message 00 - 25 26 27 28 29 Description Suggested Repair General software flags ■ Power cycle the autoloader and run the Health test. ■ Check HP website for firmware updates. Message Send ID error ■ Check SCSI Bus cables and terminators. ■ Make sure the host bus adapter is installed, detected, and configured properly. ■ Power cycle autoloader. Repeat checks after power cycle. ■ Check SCSI bus cables and terminators.
Troubleshooting Table 14: Error Messages Error Message 2A 2B-2F Description Invalid element status Firmware tables and stacks invalid Suggested Repair ■ Check host device driver. ■ Make sure the software application is supported, has the autoloader correctly configured, and has the latest patches installed. ■ Power cycle autoloader. Repeat checks after power cycle. ■ Power cycle the autoloader and run the Health test. ■ Update firmware.
Troubleshooting Table 14: Error Messages Error Message 3C Description Over temp Suggested Repair ■ ■ ■ ■ ■ Verify that room temperature is within specifications. Check that there is adequate clearance for airflow. Clear debris from any openings of the autoloader, both in the front and the back. Verify that both fans are working. If fans are bad, contact HP customer support. Power off the autoloader and allow it to cool. 3D Drive error Try a different piece of media.
Troubleshooting Table 14: Error Messages Error Message A5 A6 A7 134 Description Source element empty Source magazine missing Destination magazine missing Suggested Repair ■ Verify that the expected source really does have a cartridge. ■ Run the Health test. ■ If the source is a magazine, replace the cartridge in that slot with a different cartridge and try again. If error continues, replace the magazine. ■ If source is the tape drive, verify the tape drive has a cartridge and it was ejected.
Troubleshooting Table 14: Error Messages Error Message A8 Description Destination element full Suggested Repair ■ Verify the expected destination really does not have a cartridge. ■ If destination is a magazine, install and remove a cartridge from the selected slot and try again. If error continues, replace the magazine. ■ If destination is the tape drive verify the tape drive does not have a cartridge.
Troubleshooting Table 14: Error Messages Error Message AD Description Mail slot solenoid error Suggested Repair ■ Insert a cartridge into the autoloader via the mail slot. ■ Power cycle the autoloader. AE Unknown servo error Run the Health test. AF Error log information event No action required. B0 - BF Error events related to the picker not rotating or translating correctly. C0 D0 Unknown motor error Magazine solenoid bad ■ Run the Picker test. ■ Run the Health test.
Troubleshooting Table 14: Error Messages Error Message D2 - D4 D5 - DE DF Description Position sensor bad Cartridge flags located on the magazine may be bad or the sensor to detect the flags may have a problem Jammed cartridge Suggested Repair ■ Remove and insert each magazine. ■ Try a different magazine, if possible. ■ Power cycle the autoloader. ■ Remove and insert each magazine. ■ Try a different magazine, if possible. ■ Power cycle the autoloader.
Troubleshooting Diagnostic Tests Table 15 lists the diagnostic tests. Table 15: Diagnostic Tests Test Description Halt Cancels any currently running test. Self ■ Checks the ability of the picker to properly rotate and translate. ■ Verifies that installed magazines function correctly. ■ Verifies picker movement. ■ Verifies magazine movement. ■ Updates inventory. ■ Verifies ability to move cartridge to and from each magazine element.
Regulatory Compliance Notices A Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Regulatory Compliance Notices Declaration of Conformity for products marked with the FCC logo United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Regulatory Compliance Notices European Union Notice Products bearing the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Regulatory Compliance Notices Japanese Notice SSL1016 Tape Autoloader Reference Guide 143
Regulatory Compliance Notices 144 SSL1016 Tape Autoloader Reference Guide
Electrostatic Discharge B To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: ■ Avoid hand contact by transporting and storing products in static-safe containers.
Electrostatic Discharge Grounding Methods There are several methods for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: ■ Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum of 1 megohm ± 10 percent resistance in the ground cords. To provide proper grounding, wear the strap snug against the skin.
C Specifications Physical Specifications Table 16: Physical Specifications Height 3.5 inches (8.89 cm) Width 17.6 inches (44.70 cm) Length 27.67 inches (70.28 cm) Weight (without media) 50 lb (22.
Specifications Power Specifications Table 18: Power Specifications 148 Line Voltage 60 Hz system: 90 to 265 VAC; 50 Hz system: 90 to 135 VAC Line frequency 47 Hz to 63 Hz AC input current 60 Hz system: 6.0A (RMS) for 115VAC; 50 Hz system: 3.
Specifications Environmental Specifications Table 19: Environmental Specifications Temperature Range (Dry Bulb) Operating +10ºC to +35ºC (+50ºF to +95ºF) Non-operating - 35ºC to + 65ºC (-31ºF to +149ºF) Temperature Variation Operating 10ºC (50ºF) per hour Non-Operating 20ºC (68ºF) per hour Humidity Operating 20% to 80% non-condensing Non-Operating 10% to 90% non-condensing Gradient 10% per hour Wet Bulb Operating 26ºC (78.8ºF) max Non-Operating 29ºC (84.
Specifications Safety and Regulatory The autoloader carries the following Regulatory Agency product safety certifications.
Upgrading or Replacing the DCA D This appendix describes how to upgrade or replace the drive carrier assembly (DCA). Configuration and Tools If you replace or upgrade the autoloader DCA, you need to check settings for the DCA and the SCSI bus. You will need a Phillips screwdriver to replace a DCA. Removing a DCA Before you replace the autoloader DCA, you must make sure the tape drive does not contain a cartridge.
Upgrading or Replacing the DCA To remove the DCA: 1. Power off the autoloader. 2. Disconnect all cords and cables from the back of the DCA. 3. Remove the four screws anchoring the DCA to the chassis.
Upgrading or Replacing the DCA 4. With one hand, grasp the DCA handle and slide it backward to remove. Being careful not to touch the exposed board on the bottom of the DCA, place your other hand under the DCA to support it and prevent it from falling. Figure 91: Removing the DCA Caution: Avoid touching the exposed board on the bottom of the DCA. See Figure 92.
Upgrading or Replacing the DCA Figure 92: Bottom of DCA 154 SSL1016 Tape Autoloader Reference Guide
Upgrading or Replacing the DCA Installing a DCA To install a DCA: 1. Put on ground wrist strap and connect to appropriate ground. 2. Grasp the DCA by the handle with one hand and support it underneath with the other hand. Caution: Avoid touching the exposed PCBA on the bottom of the DCA. 3. Slide the DCA into the DCA bay 1. Make sure you position DCA correctly; it should slide smoothly. 1 2 2 Figure 93: Installing the DCA 4. Install the four screws that secure the DCA to the chassis 2. Tighten firmly.
Upgrading or Replacing the DCA 156 SSL1016 Tape Autoloader Reference Guide
index A conventions document 10 equipment symbols 11 text symbols 10 cooling fans 18 altitude 149 authorized reseller, HP 13 auto clean 124 autoloader front view 15 internal view 20 IP address 47 rear view 18 status 89 status messages 90 D SSL1016 Tape Autoloader Reference Guide Index cartridges ejecting 80 inserting into mailslot 78 inserting single 77 moving 79 using 77 cleaning auto 124 manual 122 cleaning tape ejecting 122 inserting 120 storing 120 configuration menu 41 control mode, setting 44
Index F fans, cooling 18 firmware updating 97 view version 91 front panel components 73 default password 76 function keys 16, 73 G getting help 13 H handles, rackmount, installing 30 height rackmount 147 help, obtaining 13 HP authorized reseller 13 storage website 13 technical support 13 humidity 149 I installation location 25 preparation 23 rackmount 27 SCSI bus requirements 23 standalone 34 verification 40 IP address dynamic, setting 48 setting permanent 49 158 IP gateway 50 L LCD 16, 74 LEDs defin
Index S SCSI bus requirements 23 cable requirements 24 connection 36 connector 19 ID setting 42 switch 42 terminator requirements 24 security, configuring 56 sequential mode operation 46 set compression 96, 97 SNMP server 51 status information 88 subnet mask 49 symbols in text 10 symbols on equipment 11 T tape cartridges inspecting 63 protecting 67 storing 68 transporting 68 tape drive cleaning 122 status 93 SSL1016 Tape Autoloader Reference Guide version 94 technical support, HP 13 temperature non-oper
Index 160 SSL1016 Tape Autoloader Reference Guide
