HP WBEM TC Document Number: P00114 Date: 10/08/2009 Version: 1.4.0 HP Base Server Physical Asset Profile © Copyright 2008, 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Contents Foreword ....................................................................................................................................................... 3 Introduction.................................................................................................................................................... 4 1 Scope ....................................................................................................................................................
Foreword The HP Base Server Physical Asset profile (P00114) was prepared by the HP WBEM TC. Version 1.4.
Introduction The information in this specification should be sufficient for a provider or consumer of this data to identify unambiguously the classes, properties, methods, and values that shall be instantiated and manipulated to represent HP Base Server Physical elements. The target audience for this specification is implementers who are writing CIM based providers or consumers of management interfaces representing the component described in this document. 4 Version 1.4.
1 Scope The HP Base Server Physical Asset profile extends the management capability of referencing profiles by adding the capability to represent base servers physical asset elements. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 2.
3.3 conditional used to indicate requirements strictly to be followed in order to conform to the document when the specified conditions are met 3.4 mandatory used to indicate requirements strictly to be followed in order to conform to the document and from which no deviation is permitted 3.5 may used to indicate a course of action permissible within the limits of the document 3.6 need not used to indicate a course of action permissible within the limits of the document 3.
5 Synopsis Profile Name: HP Base Server Physical Asset Profile Version: 1.4.0 Organization: HP WBEM TC CIM Schema Version: 2.12 Extends: DMTF DSP1011, Physical Asset profile 1.0 The HP Base Server Physical Asset profile extends DMTF DSP1011 to add the capability of modeling the physical aspects of HP systems. Table 1 – Related Profiles Profile Name DSP1011 – Physical Asset profile 6 Organization DMTF Version 1.
7 Implementation Requirements This section details the requirements related to the arrangement of instances and properties of instances for implementations of this profile. 7.1 7.1.1 HP_ComputerSystemChassis HP_ComputerSystemChassis.SerialNumber This property shall contain the serial number for the system. 7.1.2 HP_ComputerSystemChassis.Model This property shall contain the model name for the system. 7.1.3 HP_ComputerSystemChassis.
• • • • • “Cellular” “Single-node” “Multi-node” “Virtual system” “Virtual partition” The following table lists possible system configurations along with the expected string for HP_ComputerSystemChassis.ChassisTypeDescription as well as HP_ComputerSystemChassis. VendorEquipmentType properties. System HP_ComputerSystemChassis. ChassisTypeDescription or HP_ComputerSystemChassis.
(Single chassis with multiple servers) e.g T2 Spartan Virtual partition “Virtual partition” Example: - vPar Virtual system “Virtual system” Examples: - HPVM guest - Xen guest 7.1.10 HP_ComputerSystemChassis.PackageType (optional) This property shall contain value 16 (Blade) for Blade servers,.and 3 (Chassis/Frame) for other servers. 7.1.11 HP_ComputerSystemChassis.OtherPackageType (optional) This property does not need to be populated. 7.1.12 HP_ComputerSystemChassis.
8 Methods None. 8.1 Profile Conventions for Operations Support for operations for each profile class (including associations) is specified in the following subclauses. Each sub-clause includes either a statement “All operations are supported as described by DSP200 v1.2” or a table listing all the operations that are Unspecified by this profile or where the profile requires behavior other that described by DSP200.
9.1 Determine if HP Base Server Physical Asset profile has been implemented The following algorithm can be followed to determine if the HP Base Server Physical Asset profile has been implemented: • For any given autonomous profile, query for its CIM_RegisteredProfile instance in the interop namespace. For HP server system, this will typically be the DMTF Base Server profile (DSP1004).
Table 4 – Class: HP_ComputerSystemChassis Properties Requirement Notes SerialNumber M (see section 7.1.1) Model M (see section 7.1.2) ProductID C (see section 7.1.3) UserTracking O (see section 7.1.4) VirtualSerialNumber[] C (see section 7.1.5) VirtualUUID[] C (see section 7.1.6) TPMModule C (see section 7.1.7) ChassisPackageType O (see section 7.1.8) ChassisTypeDescription O (see section 7.1.9) PackageType O (see section 7.1.10) OtherPackageType O (see section 7.1.
11 Durable Names and Correlatable IDs Table 7 – Durable Names generated by this Profile Class Durable Name(s) Source ID Information Circumstances for Change HP_ComputerSy stemPackage UUID UUID from SMBIOS Chassis replacement HP_ComputerSy stemChassis SerialNumber Serial Number from SMBIOS Chassis replacement HP_ComputerSy stemChassis VirtualSerialNumber Virtual Serial Number as provided by Virtual Connect Logical server deletion / addition HP_ComputerSy stemChassis VirtualUUID Virtual UUID
ANNEX A (normative) Change Log Version Date Description 1.0 4/27/06 Initial Draft 1.1.0 1/22/08 Added HP Virtual Connect support (VirtualSerialNumber and VirtualUUID). 1.2.0 6/10/2008 Added the TPMModule property 1.3.0 7/30/2009 Added sections 7.1.8 - 7.1.14 to clarify data populated for various chassis type properties Version 1.4.
ANNEX B (informative) Acknowledgments 16 Version 1.4.
ANNEX C (informative) Included WBEM TC CR Numbers CR Number Date CR00103 6/14/06 Create HP Profile for the logical and physical base server model. CR00129 1/22/08 Added virtual connect related properties. Minor update 6/10/2008 Added the TPMModule property CR00152 7/30/2009 Added sections 7.1.8 - 7.1.14 to clarify data populated for various chassis type properties Version 1.4.
Bibliography This section contains a list of the external references and dependencies for this specification. 18 Version 1.4.