www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches Preparation To register your fan, please visit: www.HunterFan.com/register Downrod 12 Troubleshooting ? ? ? 17 PA G E 16 PA G E 1 M0035-01 • 05/28/13 • © Hunter Fan Company PA G E 14 PA G E 13 PA G E Maintenance & Cleaning Switch Housing 5 Canopy 11 PA G E Blades 4 Wiring 8 PA G E 7 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Pliers Ladder Screwdrivers 11/32” Wrench Wire Strippers Power Drill (optional) 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M0035-01 • 05/28/13 • © Hunter Fan Company 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket www.HunterFan.com Mounting Isolator Tapered Mounting Holes Ceiling Plate Screws Ceiling Plate Ceiling Plate Gasket 1.888.830.1326 Post er w o nP r Tu OFF Flange Nuts Ceiling Plate Ceiling Bracket Remove all four mounting isolators. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
Ceiling Bracket (continued) www.HunterFan.com 1.888.830.1326 For angled ceilings, point opening toward peak. Use the wood screw to poke holes through the rubber gasket in order to install the ceiling bracket assembly to your support structure or ceiling fan-rated outlet box. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
Ceiling Bracket (continued) Preparation www.HunterFan.com 1.888.830.1326 ! KEEP DISC D AR Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 10 M0035-01 • 05/28/13 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com O FR M CEILIN Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM CEILING FR Green/Yellow Stripe Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 12 M0035-01 • 05/28/13 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com 1.888.830.1326 Remember the screws that you kept after removing the shipping blocks (page 7)? You need them for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with the blade iron armature screws, then securely tighten after both screws are attached.
Switch Housing Align the screw holes in the switch housing gasket in the motor housing. Screw two switch housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.
www.HunterFan.com Switch Housing (continued) 1.888.830.1326 er ow P n r Tu ON Screw Holes Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the plug connectors. Lift the lower switch housing until the screw holes are aligned with the screw holes in the upper switch housing. Install the three switch housing screws found in the hardware bag.
Switch Housing (continued) Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 Reverse Switch CONGRA YOU’RETULATIONS! DONE! The pull chain controls the fan: from high to off. Changing the direction of air flow - move the reverse switch to the opposite position. 16 M0035-01 • 05/28/13 • © Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Use the provided balancing kit and instructions to balance the fan. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.