Key Biscayne Installation Manual Models: 59135 Weathered Zinc 59273 Onyx Bengal Weight ±2 lbs: 25.8 lbs (11.7 kg) ©2017 Hunter Fan Co.
1886 Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Do this first! Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
1886 Installing the Downrod Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual. The ground wire attached to the downrod is approximately 8 inches. 8” & STEP 1 (not to scale) STEP 3/8” If the setscrew is not tightened securely, the fan may fall. STRIP 2 CUT STEP Hunter Pro Tip: 3 ! KEEP Hand tighten the downrod (at least 4-5 full turns) until it stops.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Place each blade between a blade arm and blade medallion. Install three blade screws, found in the hardware bag, to attach the blade medallion to the blade arm.
1886 Preparing the Light Fixture Follow these steps to prepare the light fixture for installation. x1 KEEP Fixture Screw Repeat x2 Red Flag Remove the pre-installed fixture screw and red flag from the light kit assembly. Save the screw. It will be needed for light kit installation. Carefully remove the light fixture from the light fixture hood and set the light fixture. Remove and discard the plastic connectors from the ends of the two pull chains.
1886 Installing the Light Fixture 3 of 4 Fixture Screw bag Empty Post Fixture Screw Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors and that the connectors latch. Partially install three fixture screws, found in the hardware bag, into the posts as shown, leaving the circled post empty. Keyhole Slot Align the three keyhole slots in the light kit with the three assembly screws in the posts.
1886 Installing the Pull Chains The fan pull chain controls the speed: from high to off. Feed the pull chains from the fan switch and the light switch down through the holes in the upper switch housing as shown. Attach the pull chain pendants to the light and fan pull chains. The light pull chain controls the light fixture: on and off.
1886 Reversing the Fan Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. The reversing switch is located inside the light fixture cage. It can only be accessed when the cage is removed. Slide the reversing switch to the opposite position. Restart the fan. Reverse Switch Updraft (counterclockwise rotation) creates a more indirect airflow.
1886 Limited Lifetime Warranty • ENERGY STAR® Rated Light Kits — Three-Year Limited Warranty If your ENERGY STAR rated light kit (not including glass components) fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement light kit free of charge.* Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com.
