Minikin Installation Manual Model: 50953 Brushed Nickel 50982 Fresh White Fan weight ±2 lbs: 20.0 lbs (9.1 kg) ©2021 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: You must be able to secure the fan to building structure or fan-rated outlet box. 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location.
Wiring the Fan We know wiring is hard. Let’s make it easier. 1886 Hunter Pro Tip: Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.
1886 Installing the Motor Housing 2 of 4 2 of 4 Canopy Screw bag Canopy Screw bag Align the hanging slots on both sides of the fan body with the two partially installed canopy screws. Slide the two slots on both sides of the fan body between the head of the screws and rotate the fan body counter clockwise so the screws hold the fan body firmly in place. Partially install two of the canopy screws into screw holes on opposite corners of the ceiling plate as shown.
1886 Installing the Blades x12 Blade Arm Screw bag Ridge Lightly attach the blade arms to the mounting plate with screws found in the hardware bag, then securely tighten after all screws are attached. IMPORTANT NOTE: The blade arms should be mounted with the ridge facing downward. Installing it incorrectly could result in your fan not functioning. Repeat x4 Note: Fan style may vary.
1886 Installing the Globe r we Po n r Tu ON Tab Notch Install the included bulbs into the sockets. When necessary, replace with bulbs of same wattage. Attach the globe by lifting and turning clockwise one third of a full turn of the globe until it stops. NOTE: Check to ensure proper engagement. Lift the globe and align the notches in the globe with the tabs in the light kit. WARNING GLOBE FALL HAZARD To prevent SERIOUS INJURY, make sure that globe is properly secured. Note: Fan style may vary.
1886 Reversing the Fan Reverse Switch Updraft (clockwise rotation) creates a more indirect airflow. Updraft airflow is great for moving warm air downward. Downdraft (counterclockwise rotation) creates a direct breeze and maximum cooling effect. Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. Slide the reversing switch to the opposite position.
1886 Troubleshooting Fan Doesn’t Work Excessive Wobbling • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades are properly installed on the blade iron posts. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.