Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Preparation Ceiling Plate 1.888.227.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you.
Preparation www.CasablancaFanCo.com Tools Needed Ladder Screwdriver (included) Pliers Power Drill (optional) Wire Strippers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M8546-01 • 03/23/17 • © 2017 Casablanca Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step. 1.888.227.
Ceiling Plate www.CasablancaFanCo.com 1.888.227.2178 Bumper r we o nP r Tu OFF Make sure all four bumpers are still attached. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling plate and is acceptable for fan with hardware found in support of 31.
Hanging the Fan 1.888.227.2178 ALIGN www.CasablancaFanCo.com Unlock the canopy cover from the canopy ring tabs to loosen the canopy ring and lower it down to the fan body as shown. Note: Remove the canopy screws from the shipping plate inside the canopy. Discard the shipping plate but save the screws for canopy installation. Align the flat side of the control receiver with the flat side of the triangular seat. Lower the control receiver on the triangular seat.
Hanging the Fan www.CasablancaFanCo.com Connect Locate the single-pin connectors that are taped together. Connect the single-pin connectors from the control receiver to the connectors from the fan. Connect the white wires together. Connect the blue wires together. The third, loose wire will not be used for your installation. It is capped to prevent usage. DO NOT PICK THE FAN UP BY THE WIRES. Use the hanging hole on the body of the fan to hang the fan on the hook of the ceiling mounting plate.
Wiring: Single Switch Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. Have a single switch? Follow these steps: www.CasablancaFanCo.com green • Cap the blue wire from the fan. You will not need it for single switch wiring. TE Connect the white (grounded) wire from the ceiling to the white wire from the fan/receiver.
Wiring: Dual Switch Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. Have dual switches? Follow these steps: www.CasablancaFanCo.com OM CEILING FR OM CEILING FR green • Connect the second ungrounded (light) wire from the ceiling to the blue wire from the fan. TE Connect the white (grounded) wire from the ceiling to the white wire from the fan/receiver.
Canopy www.CasablancaFanCo.com Canopy Screw Partially install two of the canopy screws into screw holes on opposite corners of the ceiling plate as shown. Choose the two screw holes that are aligned with the hanging slots in the fan body. 1.888.227.2178 Hanging Slot Using both hands, lift the fan body from the hook and align the hanging slots on both sides of the fan body with the two partially installed canopy screws.
Canopy www.CasablancaFanCo.com Canopy Tab Holders Canopy Ring Tabs Before going to the next step, locate the two sets of canopy ring tabs that are on the top edge of the canopy and the two sets of canopy tab holders found at the top of the fan body near the ceiling. To install the canopy ring, lift the canopy, then rotate clockwise until the tabs are held in place by the tab holders, locking the canopy ring into place.
Blades Slide a blade into a slot located on the blade ring. Note: The blades will only fit properly over the screws holes one way. If the holes do not line up, remove the blade and turn it over. www.CasablancaFanCo.com Install the blade using three blade screws and washers, found in the hardware bag. Repeat this process for all five blades. 11 M8546-01 • 03/23/17 • © 2017 Casablanca Fan Company 1.888.227.
Glass www.CasablancaFanCo.com 1.888.227.2178 Tab Notch CONGRA T YOU’REULATIONS! DONE! Align the notches in the globe assembly with the tabs in the light kit fitter. Carefully lift the globe assembly as far as it will go, then rotate it counterclockwise until it is held into place by the three tabs. 12 M8546-01 • 03/23/17 • © 2017 Casablanca Fan Company See next page for fan operation instructions.
Wall Control For Single Switch www.CasablancaFanCo.com If you have a dual switch setup, go to page 18 for dual switch installation instructions. 1 Installing the Wall Plate Bracket 4 Wiring the Wall Control Snap the Wall Control into the Wall Plate Bracket. Turning off the power Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. n Tur 2 3 Installing the battery To access the battery compartment, slide the battery door up. er Pow OFF 1.
Wall Control For Single Switch 5 6 www.CasablancaFanCo.com 7 Installing the Wall Control Install the longer screws through the slots in the wall control into the switch box screw holes. Turning on the power IMPORTANT n Tur 8 Installing the Wall Plate Push the wall plate onto the Wall Plate Bracket. It should snap into place. 1.888.227.
Wall Control For Dual Switches www.CasablancaFanCo.com 2 To install the Casablanca Wall Control into a dual switch location, you will need a wall plate with both a standard switch and rocker switch cut-out (sold separately). If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. (Sold Separately) 1 Installing the battery To access the battery compartment, slide the battery door up. Battery Door Replace the used battery with two AAA batteries when needed. 1.888.
Wall Control For Dual Switches 4 Remove the existing wall plate 5 Remove the Casablanca Wall Control frame. www.CasablancaFanCo.com 7 Remove the existing wall plate. Save the screws. You will need them for the existing, marked light switch. 6 8 Wiring the Casablanca Wall Control 1. 2. 3. 4. Install the Wall Plate Install the wall plate that fits your setup (sold separately). 1. Use the screws you saved to reinstall into the light switch. 2. Remove the frame from the Casablanca Wall Control.
Wall Control www.CasablancaFanCo.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance or relamping. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 18 M8546-01 • 03/23/17 • © 2017 Casablanca Fan Company 1.888.227.
Troubleshooting www.CasablancaFanCo.com 1.888.227.2178 Fan doesn’t work Excessive wobbling Remote does not work LED lights will not dim • Press a fan speed button (up or down arrow. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Make sure the battery is installed correctly. • Use the provided balancing kit and instructions to balance the fan. • If the remote still does not work, you may need to pair your remote.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.