Installation Guide

ManualsBrandsHunter ManualsCeiling FansChanning 54 in. LED Indoor Easy Install Brushed Nickel Ceiling Fan with HunterExpress feature set

1886

Do not discard the hardware bags or mix parts from

different bags. Make note of the symbol printed on

each hardware bag. The symbols can be used to

identify the appropriate hardware for each step.

For installing the hanger bracket and wiring the fan

For installing the blades

For installing the canopy

For installing the light xture

bag

Hunter Pro Tip:

Find a part that is missing or damaged?

Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.

bag

Spare Parts

For your convenience,

you may receive extra fasteners.

bag

Bulb

Glass

Globe Retainer

Finial Cap

Finial

Light Fixture

Blade

Canopy

Canopy Screw

Ceiling Bracket

Wood Screw

WIre Nut

Washer

Fan style may vary.

Note:

M3671-01 r122617

We recommend that you pull everything out of the box and lay it out. We have

grouped the drawn components below with the hardware you’ll need for those

parts. The screws below are drawn to scale to make it easier to identify what

piece of hardware is needed to install each component.

Here is what comes in your box:

Remote

Summary of content (9 pages)

PAGE 1
886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
PAGE 2
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
PAGE 3
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
PAGE 4
1886 Hanging the Fan S li d e c a n o p y ove NOTICE rd o wn ro d an d To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. w i re s . Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this.
PAGE 5
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
PAGE 6
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 Canopy Screw Canopy Screw bag o Fi t t h e c a n py in pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Align the three blade holes with the three blade iron posts. Squeeze the blade and the blade iron post together. The flared tops of the blade iron posts will be fully visible above the blade when properly assembled. Repeat x5 Note: Fan style may vary.
PAGE 7
1886 Assembling the Light Remove the cardboard plug guard before proceeding! Notch Push the connector and excess wire into the hole at the top of the light fixture. IMPORTANT Connect the plugs from the fan and light fixture. Make sure to line up the colored markings on the connectors. The connector and excess wiring must be pushed into the light fixture in order to successfully mount the light fixture to the fan. Pin Raise the light kit to the bottom of the fan.
PAGE 8
1886 Installing the Remote Control Cradle You have two options for installing the remote cradle. Choose which path works best for you. Option 1: Using Adhesive Strip Option 2: Using Screws Remove the cradle from the cradle bracket. Separate the lining from the back of the adhesive strip on the cradle bracket. Press the cradle bracket against the wall and hold firmly for 30 seconds. Slide the cradle onto the mounted bracket. Choose your cradle installation location.
PAGE 9
1886 Troubleshooting Fan Doesn’t Work Excessive Wobbling • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. • Check the plug connection in the switch housing.