www.HunterFan.com Table of Contents 30 inches 2 Ladder Hanging the Fan Wiring Blades ? ? ? 15 PA G E 1 M0118-01 • 07/11/16 • © 2016 Hunter Fan Company 14 Troubleshooting PA G E PA G E 12 10 PA G E 9 Maintenance, Operation & Cleaning Light Kit PA G E 11 5 PA G E 7 Switch Housing 4 Motor Housing PA G E 6 3 PA G E 7 feet PA G E Save your receipt for proof of purchase. Preparation Ceiling Bracket PA G E To register your fan, please visit: www.HunterFan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you. w.
www.HunterFan.com Tools Needed Ladder Screwdrivers Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step. Power Drill (optional) 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M0118-01 • 07/11/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Ceiling Bracket 1.888.830.1326 Bumper er w o nP r Tu OFF Make sure all four bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box.
Ceiling Bracket (continued) Preparation www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0118-01 • 07/11/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Ground Wire Screw Hole While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Screw Once the motor is in the ceiling bracket, use the two locking screws found in the hardware bag to secure the motor to the ceiling bracket. Note: Fan style may vary.
Wiring: Single Switch www.HunterFan.com 1.888.830.1326 Dual Switch Instructions Have a single switch? Follow these steps: Grounded White Connect the white (grounded) wire from the ceiling to the white wire from the fan. Ungrounded w llo /Ye n e Gre Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Wiring: Dual Switch www.HunterFan.com 1.888.830.1326 Have dual switches? Follow these steps: Grounded Connect the white (grounded) wire from the ceiling to the white wire from the fan. White Str ipe w Black llo /Ye n e Gre w ipe Blue llo /Ye n e Gre Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
www.HunterFan.com Motor Housing Notch Motor Housing Screw Indentation Screw Holes Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket. The motor housing is not secured until the next step is complete. Do not leave unattended. With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag.
Blades www.HunterFan.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 10 M0118-01 • 07/11/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 11 M0118-01 • 07/11/16 • © 2016 Hunter Fan Company 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
www.HunterFan.com Light Kit 1.888.830.1326 Notch Switch Housing Screw Partially install two of the switch housing screws found in the hardware bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Want to install your fan without a light kit? Go to www.HunterFan.
www.HunterFan.com Light Kit (continued) Metal Plate Light Pull Chain 1.888.830.1326 Fan Pull Chain Globe Globe Keeper CONGRA Finial Cap YOU’RETULATIONS! DONE! Finial Install the included LED bulbs into the sockets. When necessary, replace with bulbs of same wattage. Press the globe and globe keeper flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap.
Maintenance, Operation & Cleaning r we o nP www.HunterFan.com 1.888.830.1326 Metal Plate r Tu ON Globe Globe Keeper Reverse Switch Finial Cap Finial Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Use the provided balancing kit and instructions to balance the fan. • Check to see if any of the blades are cracked.