www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Blade Irons Turn the motor assembly upside down and place it in one of the holes in the packaging. www.HunterFan.com Install a blade iron to the blade iron mounting plate using two blade iron assembly screws, found in the hardware bag. Repeat this process to install all five blade irons. 6 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company 1.888.830.
Light Kit www.HunterFan.com 1.888.830.1326 Light Kit Assembly Screw Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. Feed the 9-pin plug connector coming from the bottom of the motor housing through the center hole in the light kit assembly. Connect it to the plug connector found in the switch housing area of the light kit assembly.
www.HunterFan.com Light Kit (continued) Insert a third light kit assembly screw, found in the hardware bag, into place and tighten all three screws securely. Make sure the light kit assembly is securely attached to the motor housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Carefully push all switch housing components into the switch housing, then install the switch housing plate using two light kit assembly screws, found in the hardware bag.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 11 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring: Single Switch www.HunterFan.com 1.888.830.1326 Dual Switch Instructions Have a single switch? Follow these steps: gro Un Grounded White ou nd ing i pe Str Gr Blue Connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan.
Wiring: Dual Switch www.HunterFan.com 1.888.830.1326 Have dual switches? Follow these steps: Grounded ellow Green/Y Grounded White Gr ou Ungrounded (lig ht) Black ing rou nd ed Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. Un g Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 14 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Put each blade washer, found in the hardware bag, onto a blade screw, found in the hardware bag. Then secure each blade to a blade iron using the blade screws and washers. 15 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Bulbs & Globe Tab Notch Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. Position the notches in the outer rim of the globe so they line up with the tabs on the light kit assembly. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs. 16 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Pull Chains 1.888.830.1326 CONGRA T YOU’REULATIONS! DONE! Remove and discard the plastic connectors from the ends of the short pull chains coming from the sides of the light kit assembly. Connect the appropriate pull chain pendant to each of the short chains. The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. 17 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company See next page for fan operation instructions.
Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 r we o nP r Tu ON Reverse Switch Changing the bulbs - carefully remove the globe. Unscrew bulbs and replace with bulbs of the same wattage. Reinstall the globe. Changing the direction of air flow - carefully remove the globe and move the reverse switch to the opposite position. Reinstall the globe. 18 M3614-01 • 08/09/16 • © 2016 Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
