www.HunterFan.com Table of Contents Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3602-01 • 09/01/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 1.888.830.1326 DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. WARNING: This receiver cannot be installed in conjunction with any other receiver or hard-wired wall control. Doing so will void your warranty.
Wiring OM FR Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. CEILIN www.HunterFan.com Not for use in applications where the fan does not have a wall switch. G OM FR CEILIN 1.888.830.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 10 M3602-01 • 09/01/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Repeat this step for each blade assembly. 11 M3602-01 • 09/01/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Switch Housing Screw two light kit screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Thread theplug connector from the fan through the upper switch housing. Wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the upper switch housing is securely attached to the mounting plate.
www.HunterFan.com Light Kit Screw two light kit screws from the hardware bag halfway into the switch housing housing. It does not matter which two screw holes you choose. Make sure the light kit is securely attached to the mounting plate. Failure to properly secure all three assembly screws could result in the light fixture falling. Connect the the plugs from the switch housing and the light kit. Push excess wiring into the switch housing. Wrap keyhole slots around the screws and twist counterclockwise.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab Notch Install a light bulb in each socket. When necessary, replace with bulbs of the same wattage. Lift the globe and align the notches in the globe with the tabs in the light kit. Attach the globe by lifting and twisting clockwise until it rests firmly in place. 14 M3602-01 • 09/01/16 • © 2016 Hunter Fan Company CONGRA YOU’RETULATIONS! DONE! See next page for remote operation instructions.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw The remote transmitter is already paired to the receiver and ready to use. To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Note: If your need to pair your remote, remove the battery door.
www.HunterFan.com Remote Control Cradle 1.888.830.1326 You have two options to install the included remote control cradle to the wall. Choose which path works best for you. Option 1: Using Screws Option 2: Using Adhesive Strip Choose your cradle installation location. Remove the cradle from the cradle bracket. If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.
Operation, Maintenance, and Cleaning www.HunterFan.com 1.888.830.1326 Light Button Fan Button Fan Control Fan Operation: Press and quickly release the fan button on the remote control to turn the fan OFF or ON. Use the fan control directional pad to raise or lower the fan to the desired speed. Press and hold the fan button to reverse the fan direction. Light Operation: Press and quickly release the light button on the remote control to turn the light OFF or ON.
www.HunterFan.com 1 Download the app: 2 Launch the app. 3 Follow the onscreen prompts to set up your fan. 1.888.830.1326 Visit your app store and search Simpleconnect™ Wi-Fi to find the app. Note: The HomeKit identification number is located on the front cover of the English side of the Parts Guide. Fan not showing up in the list? Pull down to refresh! Need to install the app later? When ready, turn the wall switch off and then on. Wait three minutes before downloading the app.
www.HunterFan.com Troubleshooting 1.888.830.1326 Fan doesn’t work Excessive wobbling Noisy Operation Wireless Issues • Make sure power switch is on. • Make sure the blades are properly installed on the blade iron posts. • Make sure the blades are properly installed on the blade iron posts. • Turning the fan on and off at the switch can resolve some wireless issues. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
